MU_STRATOS_ENG_HI

More documents

Recommendations

Info

6. Installation of the system THREADED PIPE 1. Apply a sealing paste for pipes or Teflon tape on all male threaded pipes. 2. Tighten all threaded connections. CPVC PLASTIC PIPE 1. Clean, prepare and glue all joints according to the manufacturer’s instructions. OTHER Please follow the instructions from the pipes’ manufacturer when using other types of pipes and fixtures approved for drinking water. INSTALLATION OF THE DRAIN Measure and cut the necessary length, and then connect the drain line of ½” to the accessory for the drain connection of the water softener. Fasten the hose with a clamp. NOTE: Hook the hose of the drain to the underground drain. Tighten the drain hose. This will prevent any pipe whip during regenerations. HOW TO INSTALL THE ELBOW OF THE OVERFLOW DRAIN OF THE SALT TANK This programmers will provide you with information concerning the operation of the system, as well as allowing you to set up all parameters. MAIN FEATURES: User-friendly and intuitive programming. Multicolour interactive digital display. Holiday Mode Here the desired regeneration can be chosen by time, delayed, immediate or mixed. MULTICOLOUR LCD DISPLAY: It shows the information concerning the state of the system. Depending on each moment, the display will show different types of messages: Service: It offers information concerning the operation of the system. 15:57 Last Regen. : jul. 01, 2012 Mode: Meter Override Capacity Remaining Flow Rate Regeneration: It shows the regeneration stage of the system and the remaining time. It shows as well the current time. 21:02 Connect the overflow drain elbow from the system to a near drain. This drain intake must be at a lower height than the overflow drain. Advancing to Backwash NOTE: The overflow hose must be installed in such way that water cannot return from the drain hose. 6.3 STRATOS Programmer Programming: It shows the internal parameters and allows its modification. DESCRIPTION OF THE PROGRAMMER All systems have a built-in state-of-the-art electronic programmer with a multicolour interactive display. This advanced controller allows to fully monitor the operation of the system. The display is installed on the upper part of the compact cabinet. Time Holiday Mode Region & Language Advanced Settings Hardness & People System Information 16
6. Installation of the system Time Holiday Mode Date and Time Region & Language 15:57 jul. 22 , 2013 Advanced Settings Hardness & People System Information ‘MENU’ BUTTON: Press this button to go to the menus and submenus. Once inside, you can go back through the programming process. ‘SET/REGEN’ BUTTON: Press this button to trigger immediate or delayed regenerations. When programming, it allows to select the parameter as well as to confirm it. ‘+ and -’ BUTTON: Press this button to select and modify the parameter. HOW TO LOCK THE PROGRAMMER: : If no button is pressed during certain time, the programmer gets locked for security reasons, and shows the message below when any button is pressed. 15:57 Last Regen. : jul. 01, 2012 Mode: Meter Override Capacity Key Locked, Press and Remaining Hold “MENU” Key for 3 Flow Seconds to Unlock Rate To unlock the programmer, press the ‘MENU’ button during 3 seconds. IMPORTANT: When connecting the system the following message may appear: 15:57 Last Regen. : jul. 01, 2012 Mode: Meter Override Capacity Advancing to Service RemainingWait Please Flow Rate This means that the system is entering the service mode. If two minutes have gone by, and this message is still showing, please contact your distributor. 2. Press the ‘MENU’ button for 3 seconds to get into the internal program of the system. At this point you may have access to the following parameters: Time Holiday Mode Region & Language Advanced Settings Hardness & People System Information Time: The current date and time can be configured. 6.4 How to Program the System STRATOS systems are configured to carry out delayed regenerations at 2 a.m. USER PROGRAMMING: 1. Connect the supplied transformer with the electrical connector located on the rear part of the system. The programmer must be in service and show a message similar to that in the previous section. Time Holiday Mode Date and Time Region & Language 15:57 jul. 22 , 2013 Advanced Settings Hardness & People System Information 17
Page 1: Household Water Softener STRATOS Se
Page 5 and 6: Content 1. Presentation Page 01. PR
Page 7 and 8: 1. Presentation 2. INTRODUCTION The
Page 9 and 10: 2. Introduction TANK FILLING: The n
Page 11 and 12: 3. Technical Specifications 3. TECH
Page 13 and 14: 5. Previous warnings • If inlet p
Page 15: 6. Installation of the system RECOM
Page 19 and 20: 7. Start-Up System information: Thi
Page 21 and 22: 8. Maintenance / Hygienisation 7.3
Page 23 and 24: 9. Guide for the identification and
Page 25 and 26: 10. Maintenance service book NAME,
Page 27 and 28: THIS SHEET MUST BE FULFILLED BY THE

MU_STRATOS_ENG_HI

Create successful ePaper yourself

Delete template?

Save as template?