FRESAS i_Xmill

More documents

Recommendations

Info

HOLDERS STRAIGHT NECK TYPE MILL SHANK NECK LENGTH OVERALL DIAMETER EDP No. DIAMETER DIAMETER BELOW SHANK LENGTH LENGTH TYPE WRENCH SCREW (Ø D1) (Ø D2) (Ø D3) (L2) (L3) Unit : mm Ø 12 Ø 16 Ø 20 Ø 25 Ø 30, Ø 32 ZBS1201120 ZBS1202120 ZBS1601160 ZBS1602160 ZBS2001200 ZBS2002200 ZBS2501250 ZBS2502250 ZBS3001320 ZBS3002320 12 16 20 25 32 10.5 14.5 18 22.5 27 35 55 35 65 40 75 45 90 55 110 90 110 95 125 110 145 125 170 140 195 Short Regular Short Regular Short Regular Short Regular Short Regular T10 T15 T20 T25 T30 TX3512T10 TX4016T15 TX5020T20 TX6025T25 TX8030T30 TOOL STEEL HOLDER ADVANTAGES 1. Premium alloy steel with excellent strength. 2. Precise shank, Tolerance (h6). 3. Black oxide treated, to prevent corrosion and improve lubricity. 6 • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:yg1@yg1.kr
CUTTING CONDITION ASSEMBLY OF ◀ Make sure to clean the insert and insert seat. ◀ Slide the drill insert into the slot of the holder. After confirming the insert is pressed down to the bottom of the slot, tighten the screw using anti-seize compound. SIZE (Ø D) Ø 8 Ø 10 Ø 12 Ø 16 Ø 20 Ø 25 Ø 30, Ø 32 - clamping torque CLAMPING TORQUE [ N· m ] 1.0 1.5 2.5 3.5 5.0 6.0 6.5 CUTTING CONDITION RPM = revolution per minute (rev/min) Vc = surface meter per minute (M/min) Dia. = diameter of insert (mm) Vf = feed rate (mm/rev) De = effective tool diameter (mm) ap = axial depth of cut (mm) ae = radial depth of cut (mm) Vc [M/min] = (RPM) • (π) • (Dia.) 1000 Vf [mm/min] = (RPM) • (Feed) RPM [rev/min] = (Vc) • (1000) (π) • (Dia.) De [mm] = 2 (ap) • (Dia.-ap) WORK MATERIAL CARBON & ALLOY STEELS CARBON & ALLOY STEELS DIE TOOL STEELS PRE-HARDENED HARDENED STEELS HB HARDNESS HRc i-<strong>Xmill</strong> TYPE CUTTING SPEED (Normal ~ Finish) Vc [M/min] CUTTING CONDITION Feed (Vf) [mm/rev] ~280 280~380 380~480 480~ ~30 30~40 40~50 50~60 XMB110A XMB110A XMB110A, XMB120C XMB120C 160~400 120~380 100~320 180~250 ae [mm] ap [mm] Feed (Vf) [mm/rev] ae [mm] ap [mm] Feed (Vf) [mm/rev] ae [mm] ap [mm] Feed (Vf) [mm/rev] ae [mm] ap [mm] CUTTING CONDITION Ø 8 Ø 10 Ø 12 Ø 16 Ø 20 Ø 25 Ø 30, Ø 32 0.30~0.50 0.30~0.50 0.40~0.60 0.50~0.70 0.50~0.80 0.50~1.00 0.80~1.00 0.20~0.10 0.25~0.10 0.30~0.10 0.80~0.10 1.00~0.10 1.25~0.10 1.50~0.10 0.80~0.25 1.00~0.25 1.20~0.30 1.60~0.30 2.00~0.40 2.50~0.40 3.00~0.40 0.30~0.50 0.30~0.50 0.40~0.60 0.50~0.70 0.50~0.80 0.50~1.00 0.80~1.00 0.20~0.10 0.25~0.10 0.30~0.10 0.80~0.10 1.00~0.10 1.25~0.10 1.50~0.10 0.80~0.25 1.00~0.25 1.20~0.30 1.60~0.30 2.00~0.40 2.50~0.40 3.00~0.40 0.20~0.30 0.25~0.35 0.25~0.40 0.30~0.50 0.35~0.55 0.40~0.60 0.40~0.80 0.20~0.10 0.25~0.10 0.30~0.10 0.80~0.10 1.00~0.10 1.25~0.10 1.50~0.10 0.80~0.25 1.00~0.25 1.20~0.30 1.60~0.30 2.00~0.40 2.50~0.40 3.00~0.40 0.20~0.30 0.25~0.35 0.25~0.40 0.30~0.50 0.35~0.55 0.40~0.60 0.40~0.80 0.20~0.10 0.25~0.10 0.30~0.10 0.80~0.10 1.00~0.10 1.25~0.10 1.50~0.10 0.80~0.20 1.00~0.20 1.20~0.25 1.60~0.25 2.00~0.35 2.50~0.40 3.00~0.40 ▶ Recommend to reduce the feed rate to 70 ~ 85% when you use long tools. 7 • phone:+82-32-526-0909, fax:+82-32-526-4373, www.yg1.kr, E-mail:yg1@yg1.kr
Page 1 and 2: INSERTS & HOLDERS Ball
Page 3 and 4: TEST REPORT 2 Cutting Condition Too
Page 5: HOLDERS TAPER NECK TYPE Unit : mm M

FRESAS i_Xmill

Create successful ePaper yourself

Delete template?

Save as template?