2017 Dirt Freak Catalogue
Contains a great range of DRC, ZETA and more from Dirt Freak and only available in Australia from Steve Cramer Products.
Contains a great range of DRC, ZETA and more from Dirt Freak and only available in Australia from Steve Cramer Products.
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Orange<br />
Smoke<br />
Clear<br />
29<br />
32<br />
TYPE-602 LED FLASHER<br />
68 19<br />
23<br />
14<br />
M8 P=1.25<br />
( mm )<br />
MOTO<br />
LED 602 LED FLASHER<br />
- Flexible flasher stays to prevent breakage upon impact.<br />
- Lens colors available: orange, smoke and clear.<br />
- Terminals and nuts are included for installation.<br />
- Comes in pairs. Works on 12 V AC / DC.<br />
Part number<br />
D45-60-207<br />
D45-60-208<br />
D45-60-209<br />
Color<br />
Orange<br />
Smoke<br />
Clear<br />
Replacement lens<br />
Part number<br />
D45-60-287<br />
D45-60-288<br />
D45-60-289<br />
Color<br />
Orange<br />
Smoke<br />
Clear<br />
MOTO LED flashers may not work properly without optional parts.<br />
MOTO<br />
LED INDICATOR WIRING KIT<br />
This kit is required when flasher operates like hazard indicators after the IC relay installation.<br />
Place these harnesses in-between the wires from the pilot lamp and the wires from the chassis.<br />
* Some models ( *3 ) require this kit for proper operation.<br />
*3 ----- XR230, KSR110, KLX250, D-TRACKER-`07 etc.<br />
Part number D45-91-051<br />
MOTO<br />
LED RESISTOR WIRE<br />
When standard bulb flasher is replaced by LED flasher, electric consumption becomes low and<br />
stock flasher relay does not work correctly. This Resistor wire helps stabilize the electric power<br />
to the LED flasher from stock flasher relay.<br />
: Electric power consumption level is the same as with stock flasher.<br />
: Easy installation.<br />
: One resistor per flasher.<br />
* Some models ( * 2 ) require 2 resistors.<br />
: This harness will produce heat when used. Please install in areas where heat is not a problem.<br />
* 2 ----- XR230, DR250R, DRZ400S/SM etc.<br />
Part number D45-90-710<br />
MOTO<br />
LED IC RELAY for DC<br />
Stock flasher relay is designed to work with standard bulb flashers. When the stock flasher is<br />
changed to LED flashers, the stock flasher relay does not work properly due to the difference in<br />
power consumption between the stock flasher bulb and the LED flasher. This IC Relay enables<br />
LED flashers to work in any configuration.<br />
* Some models require the use of the stock IC relay along with this IC relay. ( *1 )<br />
: Reduced electrical power usage.<br />
: Some technical skills required for installation.<br />
: One IC relay required for each bike.<br />
: Flasher pilot light can not be used with position light when installed on XR250.<br />
: If the flasher operates like hazard indicators after installation, Indicator lamp wiring kit is required.<br />
: Works on 12V DC.<br />
Can not be used with WR250F/450F<br />
*1----- RMX250S, DRZ400S/SM etc.<br />
Part number D45-69-830<br />
Installation of the LED flashers requires special knowledge and technique.<br />
Please contact your local dealer if you have any question upon installation.<br />
Important note for using LED flasher<br />
LED flashers have very low consumption and the stock flasher relay may not work properly. The most frequent problem, is that the LED may<br />
flash at a quick rate using stock flasher relays. Please refer to the chart below to choose our IC relay or Resistor wire for your installation.<br />
Electric consumption Difficulty of installation Parts cost AC or DC<br />
IC Relay Low Skills required Cheap DC<br />
Resistor wire kit Same as stock Easy Reasonable DC/AC<br />
* DRC IC Relay can not be used with motorcycles ( XR50/100M, XLR250, WR250F/WR450F, XR650 etc ) due to the AC power design.<br />
Please use Resister wire kit for AC power motorcycle.<br />
129
Change language