LED_Catalogue_EN

LED Drivers
Linear / area fixed output
Specific technical data
Type
LC 75W 100–400mA flexC lp EXC
Output Min.
2) 4)
current
forward
voltage
Max. forward
voltage
Max. output
power
Typ. power consumption
(at 230 V, 50 Hz, full load)
Typ. current consumption
(at 230 V, 50 Hz, full load)
tc point
max.
Ambient
temperature ta max.
I-select 2
resistor value 3)
100 mA 60 V 220 V 22.0 W 24.3 W 114 mA 75 °C -25 ... +65 °C open
125 mA 50 V 220 V 27.5 W 30.3 W 139 mA 75 °C -25 ... +65 °C 40.0 kΩ
150 mA 50 V 220 V 33.0 W 34.3 W 156 mA 75 °C -25 ... +65 °C 33.3 kΩ
175 mA 50 V 220 V 38.5 W 41.9 W 188 mA 75 °C -25 ... +65 °C 28.6 kΩ
200 mA 50 V 220 V 44.0 W 48.4 W 215 mA 80 °C -25 ... +60 °C 25.0 kΩ
225 mA 50 V 220 V 49.5 W 53.8 W 238 mA 80 °C -25 ... +60 °C 22.2 kΩ
250 mA 50 V 220 V 55.0 W 58.8 W 260 mA 80 °C -25 ... +60 °C 20.0 kΩ
275 mA 50 V 220 V 60.5 W 64.8 W 285 mA 80 °C -25 ... +60 °C 18.2 kΩ
300 mA 50 V 220 V 66.0 W 70.7 W 311 mA 75 °C -25 ... +55 °C 16.7 kΩ
325 mA 50 V 220 V 71.5 W 76.5 W 336 mA 75 °C -25 ... +55 °C 15.4 kΩ
350 mA 50 V 214 V 75.0 W 80.6 W 353 mA 75 °C -25 ... +55 °C 14.3 kΩ
375 mA 50 V 200 V 75.0 W 80.9 W 355 mA 75 °C -25 ... +55 °C 13.3 kΩ
400 mA 50 V 188 V 75.0 W 80.6 W 354 mA 75 °C -25 ... +55 °C short circuit (0 Ω)
1)
Depending on the selected output current.
2)
The table only lists a number of possible operating points but does not cover each single point. The output current can be set within the total value range in 1-mA-steps.
3)
Not compatible with I-select (generation 1).
4)
Output current is mean value.
ACCES-
SORIES
I-SELECT 2 PLUG PRE / EXC
Product description
• Ready-for-use resistor to set output current value
• Compatible with LED Driver featuring I-select 2 interface;
not compatible with I-select (generation 1)
• Resistor is base isolated
• Resistor power 0.25 W
• Current tolerance ± 2 % additional to output current tolerance
• Compatible with LED Driver series PRE and EXC
Example of calculation
• R [kΩ] = 5 V / I_out [mA] x 1000
• Resistor value tolerance ≤ 1 %; resistor power ≥ 0.1 W;
base isolation necessary
• When using a resistor value beyond the specified range, the
output current will automatically be set to the minimum value
(resistor value too big), respectively to the maximum value
(resistor value too small)
Ordering data
9
5,5 4,5
xxxx
xxxx
Type Article number Colour Marking Current
7,5
13,5
3,5
Packaging
bag
Weight
per pc.
I-SELECT 2 PLUG 125MA BL 28001101 Blue 0125 mA 125 mA 10 pc(s). 0.001 kg
I-SELECT 2 PLUG 150MA BL 28001102 Blue 0150 mA 150 mA 10 pc(s). 0.001 kg
I-SELECT 2 PLUG 175MA BL 28001103 Blue 0175 mA 175 mA 10 pc(s). 0.001 kg
I-SELECT 2 PLUG 200MA BL 28001104 Blue 0200 mA 200 mA 10 pc(s). 0.001 kg
I-SELECT 2 PLUG 225MA BL 28001105 Blue 0225 mA 225 mA 10 pc(s). 0.001 kg
I-SELECT 2 PLUG 250MA BL 28001106 Blue 0250 mA 250 mA 10 pc(s). 0.001 kg
I-SELECT 2 PLUG 275MA BL 28001107 Blue 0275 mA 275 mA 10 pc(s). 0.001 kg
I-SELECT 2 PLUG 300MA BL 28001108 Blue 0300 mA 300 mA 10 pc(s). 0.001 kg
I-SELECT 2 PLUG 325MA BL 28001109 Blue 0325 mA 325 mA 10 pc(s). 0.001 kg
I-SELECT 2 PLUG 350MA BL 28001110 Blue 0350 mA 350 mA 10 pc(s). 0.001 kg
I-SELECT 2 PLUG 375MA BL 28001111 Blue 0375 mA 375 mA 10 pc(s). 0.001 kg
I-SELECT 2 PLUG 400MA BL 28001112 Blue 0400 mA 400 mA 10 pc(s). 0.001 kg
I-SELECT 2 PLUG MAX BL 28001099 Blue MAX MAX 10 pc(s). 0.001 kg
264
www.tridonic.com
Catalogue 2017