sharp_ar-5618_5620_5623
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Main<br />
code<br />
Sub<br />
code<br />
Contents<br />
44 01 Toner density control Enable/<br />
Disable (ON/OFF) setting<br />
Details of operation<br />
Setting is made whether the toner density control is performed or not.<br />
When this simulation is executed, the current code number is displayed on the 7-seg display. (1=ON<br />
[Enable], 0=OFF [Disable])<br />
Enter a code number and press [START] key, and the setting is settled and saved into the EEPROM<br />
and the machine goes into the sub code input standby mode.<br />
Switching can be made with [AUTO/TEXT/PHOTO] key, and the set value of the selected mode is<br />
displayed on the copy quantity display section.<br />
The entered value at that time is written into the EEPROM.<br />
LED Setting mode Default<br />
AUTO indicator<br />
TEXT indicator<br />
AUTO indicator & PHOTO indicator<br />
TEXT indicator & PHOTO indicator<br />
AUTO indicator & TEXT indicator &<br />
PHOTO indicator<br />
Print ration correction<br />
Life correction<br />
Drip infusion<br />
Purge process<br />
Unconditional toner supply<br />
1<br />
18/20cpm machine: 0<br />
23cpm machine:1<br />
0<br />
0<br />
1<br />
<br />
Print ratio correction<br />
In this correction, the toner supply interval is determined according to the print ratio, and an<br />
overtoner is prevented.<br />
Life correction<br />
When the life of any consumable p<strong>ar</strong>t approached the end, this correction prevents against<br />
undertoner.<br />
Note for items m<strong>ar</strong>ked with<br />
Drip infusion and Purge process <strong>ar</strong>e simulations for analysis, and do not set them to "Enable=1" in<br />
the m<strong>ar</strong>ket.<br />
If these items <strong>ar</strong>e set to "Enable=1", the toner density rises or falls extremely, resulting in developer<br />
fall and toner dispersion.<br />
If they <strong>ar</strong>e set to "Enable=1", developer must be replaced and the machine inside and the process<br />
unit must be cleaned.<br />
16 Toner density control data check<br />
and toner density control<br />
correction amount display<br />
Unconditional toner supply<br />
When the DV unit and the drum unit run idle, a small quantity of toner is consumed. To supply this<br />
consumption, toner is supplied according to the rotation time of the DV unit.<br />
The output value of the ATC sensor is checked and the toner density control correction value is<br />
displayed on the 7-seg display.<br />
The display mode can be switched by pressing [AUTO/TEXT/PHOTO] key.<br />
When [Interrupt] key is pressed, the machine goes into the sub code input standby mode. When [CA]<br />
key is pressed, the machine goes out of the simulation mode.<br />
LED<br />
AUTO indicator<br />
TEXT indicator<br />
Display content<br />
The current output value of the ATC sensor is displayed.<br />
The correction value according to the progress of life is added to the<br />
current output value of the ATC sensor and the sum is displayed.<br />
34 Transfer current setting Used to set the transfer current for the front surface and that for the back surface. When this<br />
simulation is executed, the current set value is displayed on the 7-seg display. Select the set value<br />
with the zoom [Zoom] keys and press the [START] key, and the set content is written into the<br />
EEPROM and the machine goes into the sub code input standby mode. Press the [AUTO/TEXT/<br />
PHOTO] key to select each setting mode. At that time, the setup content is written into the EEPROM.<br />
The set range is 90uA ~ 360uA in the increment of 10uA.<br />
LED<br />
AUTO indicator<br />
TEXT indicator<br />
AUTO indicator & PHOTO indicator<br />
TEXT indicator & PHOTO indicator<br />
AUTO & TEXT & PHOTO indicator<br />
* Small size paper must be Letter R (A4R) or smaller.<br />
* For the special size of tray, use the normal size width.<br />
Setting mode<br />
Normal size width: Front<br />
Normal size width: Back(Duplex model only)<br />
Small size width: Front<br />
Small size width: Back(Duplex model only)<br />
Bypass tray<br />
AR-<strong>5618</strong>S SIMULATIONS 7-14