GENERAL SPECIFICATIONS BINDER - Paint for professionals

More documents

Recommendations

Info

MAStER SpEciFicAtioNS iNtERioR FiNiSHiNG 1. SYStEM FoR GYpSuM BoARd cEiLiNGS, GYpSuM pANELS ANd pouREd coNcREtE Apply one coat of latex primer-sealer such as Sico Expert 870-799, CGSB 1.119 and MPI-50 approved. VOC: 147 g/L. Apply two coats of flat finish latex for ceilings such as Sico Expert 871-116, Type MPI-53. VOC: 87 g/L. Gloss (60°): 0 to 5%. 2. SYStEM FoR GYpSuM BoARd WALLS, GYpSuM pANELS ANd pouREd coNcREtE Apply one coat of latex primer-sealer such as Sico Expert 870-799, CGSB 1.119 and MPI-50 approved. VOC: 147 g/L. AlKYD fInIsh Apply two coats of velvet finish alkyd such as Sico Expert 883-series, CGSB 1.202 Type I approved. Gloss (60°): 5 to 12%. Apply two coats of pearl finish alkyd such as Sico Expert 886-series, CGSB 1.202 Type II approved. Gloss (60°): 20 to 30%. Apply two coats of semi-gloss finish alkyd such as Sico Expert 887-series, CGSB 1.57 approved. Gloss (60°): 35 to 45%. lAtex fInIsh Apply two coats of low VOC eggshell finish latex such as Sico Expert 872-series, compliant with the Green Seal GS-11 standard. VOC: 40 g/L. Gloss (60°): 0 to 5%. Apply two coats of low VOC velvet finish 100% acrylic latex such as Sico Expert 873-series, compliant with the Green Seal GS-11 standard and CGSB 1.209 and MPI-44 approved. VOC: 125 g/L. Gloss (60°): 5 to 12%. Apply two coats of satin finish latex such as Sico Design Chamois 712-series (washable satin finish), compliant with the Green Seal GS-11 standard. VOC: 0 g/L. Gloss (60°): 4 to 10%. Apply two coats of low VOC platinum finish 100% acrylic latex such as Sico Expert 874-series, compliant with the Green Seal GS-11 standard and CGSB 1.209 and MPI-52 approved. VOC: 137 g/L. Gloss (60°): 10 to 20%. Apply two coats of low VOC melamine finish 100% acrylic latex such as Sico Expert 875-series. VOC: 147 g/L. Gloss (60°): 20 to 30%. Apply two coats of low VOC semi-gloss finish latex such as Sico Expert 877-series, compliant with the Green Seal GS-11 standard and CGSB 1.195 approved. VOC: 138 g/L. Gloss (60°): 35 to 45%. Apply two coats of flat finish latex such as Sico Design Cashmere 711-series (washable flat finish), compliant with the Green Seal GS-11 standard. VOC: 0 g/L. Gloss (60°): 0 to 5%. Apply two coats of semi-gloss finish latex such as Sico Design Shantung 715-series (washable semi-gloss finish), compliant with the Green Seal GS-11 standard. VOC: 0 g/L. Gloss (60°): 20 to 30%. . SYStEM FoR coNcREtE BLocK WALLS Apply one coat of primer-block filler for concrete block such as Sico Expert 675-115, CGSB 1.188 and MPI-4 approved. VOC: 94 g/L. Apply two coats of gloss epoxy ester enamel such as Sico Expert 603-series, CGSB 1.59 approved. Gloss (60°): +80% OR – Select a finish listed in No. 2. OR – Apply two coats of 100% acrylic latex/urethane such as Sico 261-series, CGSB 1.154 approved. VOC: 137 g/L. Gloss (60°): 20 to 30%. p. 6 4. SYStEM FoR Wood SuRFAcES to BE pAiNtEd (dooRS oR WoodWoRK) Seal knots or sap streaks with a coat of shellac such as Sico 205-112. Apply one coat of alkyd primer such as Sico Expert 880-114, CGSB 1.38 and MPI-46 approved, and two finishing coats (selected according to the list in No. 2). OR – Apply two coats of 100% acrylic latex/urethane such as Sico 261-series, CGSB 1.154 approved. VOC: 137 g/L. Gloss (60°): 20 to 30%. 5. SYStEM FoR WoodWoRK to BE StAiNEd WitH ALKYd Apply one coat (or more if required) of pigmented alkyd stain such as Sico 206-series, MPI-90 approved. Apply three coats of urethane varnish such as Sico Expert 901-101 (gloss), MPI-56 approved. Gloss (60°): 85 to 95%. OR – Apply three coats of urethane varnish such as Sico Expert 901-106 (semi-gloss), MPI-57 approved. VOC: 137 g/L. Gloss (60°): 25 to 30%. 6. SYStEM FoR WoodWoRK otHER tHAN FLooRS to BE StAiNEd WitH LAtEX Apply one coat (or more if required) of pigmented latex stain such as Sico 118-series. VOC: 111 g/L. Apply three coats of clear latex varnish such as Sico 194-090 (gloss), MPI-130 approved. VOC: 201 g/L. Gloss (60°): +80%. OR – Apply three coats of clear latex varnish such as Sico 194-100 (semi-gloss), MPI-128 approved. VOC: 182 g/L. Gloss (60°): 35 to 45%. 7. SYStEM FoR GiViNG A NAtuRAL FiNiSH to WoodWoRK otHER tHAN FLooRS Apply three coats of urethane varnish such as Sico Expert 901-101 (gloss), MPI-56 approved. Light sanding between each coat is recommended. Gloss (60°): 85 to 95%. OR – Apply three coats of urethane varnish such as Sico Expert 901-106 (semi-gloss), MPI-57 approved. Light sanding between each coat is recommended. Gloss (60°): 25 to 30%. OR – Apply the latex system with three coats of Crystalex clear varnish such as Sico 194-090 (gloss), MPI-130 approved. Light sanding between each coat is recommended. VOC: 201 g/L. Gloss (60°): +80%. OR – Apply the latex system with three coats of Crystalex clear varnish such as Sico 194-100 (semi-gloss), MPI-128 approved. Light sanding between each coat is recommended. VOC: 182 g/L. Gloss (60°): 35 to 45%. 8. SYStEM FoR coNcREtE FLooRS Apply one coat of alkyd floor enamel such as Sico Expert 603-series, CGSB Type 1.73, to which 10 – 15% of Sico 875-104 thinner, CGSB 1.4 approved is added. Apply two coats of alkyd floor enamel such as Sico Expert 603-series, CGSB Type 1.73. 9. SYStEM FoR pRiMEd oR uNpRiMEd FERRouS MEtAL SuRFAcES Apply one coat of zinc phosphate primer for metal such as Sico Expert 922-260, MPI-135 approved (for primed surfaces, touch up any bare spots). Apply two coats of pearl finish alkyd enamel such as Sico Expert 886-series, CGSB 1.202 approved, Type II; OR – two coats of gloss finish enamel such as Sico Expert 603-series, CGSB 1.59 approved; OR – two coats of rust-resistant paint for metal such as the Sico 635-series Corrostop Ultra.
10. SYStEM FoR ziNc-coAtEd oR GALVANizEd MEtAL SuRFAcES Treat the surface with a metal cleaner and rust remover such as Sico 635-104. Pressure rinse with clear water. Apply one coat of latex primer for galvanized metal such as Sico 635-045. VOC: 148 g/L. Apply two coats of finish according to the list in No. 2. 11. SYStEM FoR LARGE StEEL dEcK cEiLiNGS ANd StEEL BRidGiNG According to the manufacturer’s specifications, apply dry fall spray paint such as Sico Expert 881-series (flat finish). VOC: 335 g/L. Gloss (60°): 0 to 5%. OR – According to the manufacturer’s specifications, apply dry fall spray paint such as Sico Expert 882-125 series (eggshell finish). VOC: 423 g/L. Gloss (60°): 0 to 5%. OR – According to the manufacturer’s specifications, apply dry fall spray paint such as Sico Expert 871-140, MPI-118 approved. VOC: 11 g/L. Gloss (60°): 0 to 6%. EXtERioR FiNiSHiNG 1. SYStEM FoR Wood SuRFAcES to BE pAiNtEd Apply one coat of exterior alkyd primer such as Sico Expert 980-110, CGSB Type 1.189. Apply two coats of flat finish exterior acrylic latex such as Sico Expert 971-series, CGSB 1.138 approved; OR – semi-gloss 977-series; OR – gloss 978-430 (white only). 2. SYStEM FoR pRiMEd oR uNpRiMEd FERRouS MEtAL SuRFAcES Apply one coat of zinc phosphate alkyd primer such as Sico Expert 922-260 (for primed surfaces, touch up any bare surfaces). Apply two coats of alkyd enamel such as Sico Expert 603-series, CGSB 1.59 approved. OR – Apply two coats of rust-resistant paint for metal such as Sico 635-series Corrostop Ultra. . SYStEM FoR ziNc-coAtEd oR GALVANizEd MEtAL SuRFAcES Treat the surface with Sico 635-104 cleaner and rust remover for metal. Pressure rinse with clear water. Apply one coat of latex primer for galvanized metal such as Sico 635-045. Apply two coats of alkyd enamel such as Sico Expert 603-series, CGSB 1.59 approved. OR – Apply two coats of acrylic latex such as Sico Expert 977-series (except for roofs). OR – Apply two coats of rust-resistant paint for metal such as Sico 635-series Corrostop Ultra. 4. SYStEM FoR MASoNRY, coNcREtE ANd FiBRE cEMENt SuRFAcES Apply two coats of flat acrylic latex such as Sico Expert 971-series, CGSB 1.138 approved. OR – Apply two coats of textured acrylic latex such as Sico Expert 651 (1-GP-162). MAStER SpEciFicAtioNS FoR zERo Voc iNtERioR FiNiSHiNG Green Seal certified (GS-11) 1. SYStEM FoR GYpSuM BoARd cEiLiNGS, GYpSuM pANELS ANd pouREd coNcREtE Apply one coat of zero VOC latex primer-sealer such as Sico Ecosource 850-130, Green Seal GS-11 approved. Apply two coats of zero VOC flat latex for ceilings such as Sico Ecosource 851-116 (white), Green Seal GS-11 and MPI-143 approved. Gloss (60°): 0 to 5%. 2. SYStEM FoR GYpSuM BoARd WALLS, GYpSuM pANELS, pouREd coNcREtE ANd coNcREtE BLocK Apply one coat of zero VOC latex primer-sealer such as Sico Ecosource 850-130, Green Seal GS-11 approved. Apply two coats of zero VOC velvet finish 100% acrylic latex such as Sico Ecosource 853-series, Green Seal GS-11 and MPI-144 approved. Gloss (60°): 5 to 12%. OR – Apply two coats of zero VOC melamine finish 100% acrylic latex such as Sico Ecosource 855-series, Green Seal GS-11 approved. Gloss (60°): 20 to 30%. OR – Apply two coats of flat finish latex such as Sico Design Cashmere 711-series (washable flat finish), compliant with the Green Seal GS-11 standard. Gloss (60°): 0 to 5%. OR – Apply two coats of satin finish latex such as Sico Design Chamois 712-series (washable satin finish), compliant with the Green Seal GS-11 standard. Gloss (60°): 4 to 10%. OR – Apply two coats of semi-gloss finish latex such as Sico Design Shantung 715-series (washable semi-gloss finish), compliant with the Green Seal GS-11 standard. Gloss (60°): 20 to 30%. . SYStEM FoR Wood SuRFAcES to BE pAiNtEd (dooRS oR WoodWoRK) Seal knots or sap streaks with a coat of shellac such as Sico 205-112. Apply one coat of low VOC latex primer such as Sico Expert 870-177, Green Seal GS-11 approved. Apply two coats of zero VOC melamine finish 100% acrylic latex such as Sico Ecosource 855-series, Green Seal GS-11 approved. Gloss (60°): 20 to 30%. OR – Apply two coats of zero VOC semi-gloss finish 100% acrylic latex such as Sico Ecosource 857-series, Green Seal GS-11 approved. Gloss (60°): 35 to 45%. Note: For work that must meet more stringent requirements for physical and chemical resistance, see the Sierra line of zero VOC coatings by Rust-Oleum. Consult your technical representative for further information. For more details, visit www.sicopro.ca. p. 7
Page 1: General specifications binder
Page 4 and 5: EcoSouRcE EXpERt our GREEN SEAL cer
Page 6 and 7: e) COnCrete Concrete shall have cur
Page 10 and 11: WALLBoARdS (Gypsum) Wood p. 8 suBst
Page 12 and 13: coNcREtE tHERMAL iNSuLAtioN coLd Ro
Page 14 and 15: coNcREtE ANd MASoNRY ASpHALt pRE-Fi
Page 16 and 17: otHER SuRFAcES p. 14 suBstrAte Cera
Page 18: p. 16 CODe BrAnD Green seAl 882-125

GENERAL SPECIFICATIONS BINDER - Paint for professionals

Create successful ePaper yourself

Delete template?

Save as template?