grEAsE gUns - Smarowniczki.pl

■ Umeta grease Fittings ACCORDING TO SAE J-534
VERSIONS
In general, our grease fittings according to SAE are made of steel, case
hardened, zinc-plated, passivated and featured with a special surface
treatment. For safety reasons and in order to avoid abrasion wear, the
standard for SAE-grease fittings demands a specific surface hardness
of 83 HR15 N minimum according to Rockwell hardness test procedure.
G R E ASE FI T T I N G S
ACCORDING TO SAE J-534
SPECIAL INFORMATION
For a better overview we added the international
Alemite-reference numbers to our grease fittings.
A general comparison of the relevant types you
will find on page 78.
Umeta HYDraULiC-tYPe grease Fittings ACCORDING TO SAE J-534
The SAE-standard for hydraulic-type grease fittings requires a tapered thread.
The standard head-Ø is 6.6 (+/- 0.3) mm / 0.26" (+/- 0.012").
Type H1
Hydraulic-type grease Fittings
· according to SAE J-534
· straight version A/180°
· standard versions according to SAE
are made of steel, hardened, zinc
plated, passivated and top coated
· salt spray resistance > 72 hours
GW 1/8" PtF
Ref.- No.:
L1 L2 L3 SW Steel SST303 Alemite
11/16" 5/32" 19/64" 7/16"HEX 5546006 1610-BL
9/16" 5/32" 15/64" 7/16"HEX 5546008 1644-B
1 1/4" 5/16" 25/32" 7/16"HEX 5546010 1607-B
1 3/4" 5/16" 1 17/64" 7/16"HEX 5546012 1669-B
2 5/8" 5/16" 2 3/16" 3/8"HEX 5546014 1684-B
3/4" 3/16" 5/16" 7/16"HEX 5546086 1961-S
1" 9/32" 5/16" 1/2"HEX *1) 5546016 1618-B
GW 1/4" PtF
Ref.- No.:
L1 L2 L3 SW Steel SST303 Alemite
7/8" 15/64" 27/64" 9/16"HEX 5546028 1627-B
7/8" 25/64" 27/64" 15 mm HEX 5546154 -
GW 1/4" - 28 sae-Lt
Ref.- No.:
L1 L2 L3 SW Steel SST303 Alemite
35/64" 7/64" 3/16" 5/16"HEX 5546030 1641-B
11/16" 13/64" 23/64" 5/16"HEX 5546032 1652-B
31/32" 13/64" 5/8" 5/16"HEX 5546034 1680-B
1 1/8" 13/64 25/32" 5/16"HEX 5546036 1698-B
1 5/8" 13/64" 1 9/32" 5/16"HEX 5546038 3014-B
17/32" 7/64" 3/16" 5/16"HEX 5546087 1966-S
OPERATING INSTRUCTIONS
As suitable lubricating nozzle for our hydraulic-type fittings, we recommend
our hydraulic couplers.
GW = thread
L1 = overall length
L2 = thread length
L3 = shank length
SW = HEX size
GW 1/4" - 28 UnF-2a
Ref.- No.:
L1 L2 L3 SW Steel SST303 Alemite
33/64" 5/64" 5/32" 9/32"HEX 5546106 1792-B
GW 3/8" - 18 nPtF
Ref.- No.:
L1 L2 L3 SW Steel SST303 Alemite
20 mm 8 mm 17 mm HEX *2) 5547001
GW 6/40" UnF-2a
Ref.- No.:
L1 L2 L3 SW Steel SST303 Alemite
1/2" 7/64" 1/8" 1/4"HEX *3) 5546507 3018
GW 10/32" UnF-2a
Ref.- No.:
L1 L2 L3 SW Steel SST303 Alemite
1/2" 7/64" 1/8" 1/4"HEX *3) 5546503 3016
type H1 Hydraulic-type grease Fitting with pin valve, leakproof
GW 1/8" PtF
Ref.- No.:
L1 L2 L3 SW Steel SST303 Alemite
3/4" 17/64" 5/16" 7/16"HEX 5546110 1650
*1) female thread
*2) molybdenum-surface finish
*3) no ball check
71