Stober 3 MGS Speed Reducers

More documents

Recommendations

Info

KSS Series: RIGHT ANGLE — Solid Shaft/Hollow Output Input HP 1750 RPM Input Output Torque (lb-in) Nominal Ratio Overhung Load Output Shaft 1) (lbs) Part Number Codes (in blue) Base Module Motor Adapter Compatible NEMA C-Frame 2) with Designated Motor Adapter 27 RPM Output (Approximate) 0.78 1,772 66.027 1,229 KSS203_0660 MS2R050 56C 1.38 3,100 65.499 1,465 KSS303_0650 MS3R050 MS3R140 56C 143/145TC 1.32 3,016 66.346 2,298 KSS403_0660 MS4R050 56C 2.10 4,872 67.298 2,309 KSS403_0670 2.16 4,872 65.499 2,288 KSS403_0650 25 RPM Output (Approximate) MS4R050 MS4R140 MS4R050 MS4R140 56C 143/145TC 56C 143/145TC 0.25 616 70.029 1,064 KSS102_0700 MS1R050 56C 0.75 1,772 68.419 1,244 KSS203_0680 MS2R050 56C 1.35 3,100 66.868 1,473 KSS303_0670 1.35 3,283 69.338 2,332 KSS402_0690 22 RPM Output (Approximate) MS3R050 MS3R140 MS4R050 MS4R140 56C 143/145TC 56C 143/145TC 0.65 1,772 79.615 1,308 KSS203_0800 MS2R050 56C 1.15 3,100 78.410 1,532 KSS303_0780 1.81 4,872 78.095 2,426 KSS403_0780 19 RPM Output (Approximate) MS3R050 MS3R140 MS4R050 MS4R140 56C 143/145TC 56C 143/145TC 0.57 1,772 90.787 1,350 KSS203_0910 MS2R050 56C 1.00 3,100 90.061 1,575 KSS303_0900 1.57 4,872 90.061 2,520 KSS403_0900 16 RPM Output (Approximate) MS3R050 MS3R140 MS4R050 MS4R140 56C 143/145TC 56C 143/145TC 0.47 1,772 109.471 1,350 KSS203_1090 MS2R050 56C 0.84 3,100 107.814 1,575 KSS303_1080 1.32 4,872 107.381 2,520 KSS403_1070 MS3R050 MS3R140 MS4R050 MS4R140 1) Overhung Load is measured at the center of the shaft extension. Hollow output units are not intended to support overhung loads. If a load rating is required, use 50% of the published overhung load. 2) Motor HP for TEFC NEMA C-Frame @ 1750 RPM C-Frame 56C 143/145TC 182/184 HP 1/4 to 1-1/2 1 to 2 3 to 5 56C 143/145TC 56C 143/145TC 22 MGS ® Speed Reducers V.29 800.711.3588 • www.stober.com
Selection Data IP69K/STAINLESS STEEL Input HP 1750 RPM Input Output Torque (lb-in) Nominal Ratio Overhung Load Output Shaft 1) (lbs) Part Number Codes (in blue) Base Module Motor Adapter Compatible NEMA C-Frame 2) with Designated Motor Adapter 13 RPM Output (Approximate) 0.38 1,772 135.335 1,350 KSS203_1350 MS2R050 56C 0.67 3,100 134.292 1,575 KSS303_1340 MS3R050 56C 1.05 4,872 134.399 2,520 KSS403_1340 10 RPM Output (Approximate) MS4R050 MS4R140 56C 143/145TC 0.28 1,772 181.048 1,350 KSS203_1810 MS2R050 56C 0.50 3,048 178.737 1,575 KSS303_1790 MS3R050 56C 0.77 4,737 179.056 2,520 KSS403_1790 MS4R050 56C 8 RPM Output (Approximate) 0.19 1,407 217.538 1,350 KSS203_2180 MS2R050 56C 0.13 1,172 271.923 1,350 KSS203_2720 MS2R050 56C 0.51 3,752 215.391 2,520 KSS403_2150 MS4R050 56C 6 RPM Output (Approximate) 0.19 1,407 217.538 1,350 KSS203_2180 MS2R050 56C 0.13 1,172 271.923 1,350 KSS203_2720 MS2R050 56C 1) Overhung Load is measured at the center of the shaft extension. Hollow output units are not intended to support overhung loads. If a load rating is required, use 50% of the published overhung load. 2) Motor HP for TEFC NEMA C-Frame @ 1750 RPM C-Frame 56C 143/145TC 182/184 HP 1/4 to 1-1/2 1 to 2 3 to 5 KSS Series: RIGHT ANGLE — Solid Shaft / Hollow Output 800.711.3588 • www.stober.com MGS ® Speed Reducers V.29 23
Page 1 and 2: MGS ® Speed Reducers Geared to a h
Page 3 and 4: Geared to a higher standard Conten
Page 5 and 6: Geared to a higher standard Servic
Page 7 and 8: Wobble Free Bushing Design KSS F K
Page 9 and 10: Overview Selection At-a-Glance IRON
Page 11 and 12: Application Specific Sizing Determi
Page 13 and 14: Overview IP69K/STAINLESS STEEL KSS
Page 15 and 16: Selection Data IP69K/STAINLESS STEE
Page 21: Selection Data IP69K/STAINLESS STEE
Page 25 and 26: Dimensional Data IP69K/STAINLESS ST
Page 33 and 34: Overview K/KL Ordering Options At-a
Page 35 and 36: Overview K Output and Housing Confi
Page 37 and 38: Overview K Mounting Position Option
Page 39 and 40: Overview K/KL Sizing/Selection: 1.
Page 41 and 42: Selection Data 1750 RPM Input Part
Page 49 and 50: Selection Data Input HP 1750 RPM In
Page 61 and 62: Selection Data Input HP 1750 RPM In
Page 67 and 68: Dimensional Data KL Series with “
Page 69 and 70: Dimensional Data KL Series (KL202 o
Page 71 and 72: Dimensional Data Torque Arm Mountin
Page 73 and 74:
Dimensional Data Table 1 K Series U
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Dimensional Data Table 1 Flange Dim
Page 89 and 90:
Overview C Ordering Options At-a-Gl
Page 91 and 92:
Overview C Mounting Position Option
Page 93 and 94:
Selection Data C Sizing/Selection:
Page 95 and 96:
Selection Data 1750 RPM Input Part
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Selection Data Input HP 1750 RPM In
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Dimensional Data Optional Output Fl
Page 123 and 124:
Dimensional Data Table 1 C Series U
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Overview F Ordering Options At-a-Gl
Page 133 and 134:
Overview F Series Output Options BL
Page 135 and 136:
Selection Data F Sizing/Selection:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Selection Data “A” Hollow Outpu
Page 145 and 146:
Dimensional Data Table 3 F Series U
Page 147 and 148:
Dimensional Data “V” Shaft Outp
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Technical Reference C Series Solid
Page 155 and 156:
Technical Reference Motor Adapter C
Page 157 and 158:
Returns Policy Return Delivery Note
Page 159 and 160:
Other Products from STOBER ServoSto
show all

Stober 3 MGS Speed Reducers

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?