USD 2159 AVL - Filtra

SUPRAdisc AKS
Technical Specifications
Operating Characteristics*
Maximum Operating 80°C (176°F) in Polypropylene design
Temperature 160°C (320°F) in Polyamide design
Maximum Operating Pressure 2.4 bard (35 psid)
* With compatible fluids, which do not soften, swell or adversely affect the products
or its material of construction.
3
Plastic Parts of Construction of SUPRAdisc Modules
SUPRAdisc Components Polypropylene (Standard version)
Polyamide (High temperature version)
O-rings Silicone elastomer
Filter Media Configurations
Code Filter
Type
See Above Table
New York - USA
+1 516 484 5400 phone
+1 516 801 9548 fax
pharmafilter@pall.com e-mail
Portsmouth - Europe
+44 (0)23 9230 3303 phone
+44 (0)23 9230 2506 fax
BioPharmUK@europe.pall.com e-mail
Sterilization
Steam in Place 125°C (257°F) for 30 minutes
at 0.3 bard (4.3 psid) maximum.
Nominal Dimensions
Nominal Total Length
Double O-ring 332 mm (13.1 in)
Flat Gasket 272 mm (10.7 in)
Nominal Diameter 284 mm (11.2 in) (1)
(1) Filter area codes 205, 209, 214 and 215.
(2) Filter area code 416 only.
Code Gasket
Material
410 mm (16.1 in) (2)
Code Depth Filter Mass per Unit Ash Content Extractable Ions Soluble in Acetic Acid
(For Part Number Structure)
Type Area (g/m 2 ) in % (5%) (mg/m 2 )
Part Numbering and Ordering Information
Code Module
Version
00 Standard
01 High
temperature
30 Increased
cell
distance
Code Adapter
S Double
O-ring
C Flat
Gasket
Code Filter
Area
205 0.5 m 2 (5.4 ft 2 )*
209 1.0 m 2 (10.7 ft 2 )
214 1.5 m 2 (16.1 ft 2 )**
215 1.7 m 2 (18.2 ft 2 )***
416 3.7 m 2 (39.8 ft 2 )
* Only available with double
O-ring.
** Only AKS 5 and AKS 6
*** Only AKS4
Ca Fe Al
XAK4 AKS 4 1050 13 2000 100 100
XAK5 AKS 5 1400 < 1 550 20 15
XAK6 AKS 6 1400 < 1 1000 25 10
S Silicone
elastomer
Other gaskets available on
request
Code Plastic Parts
P Polypropylene
A Polyamide (2)
(2) High Temperature only.
Visit us on the web at www.pall.com/biopharmaceutical
Pall Corporation has offices and plants throughout the world in locations including:
Argentina, Australia, Austria, Belgium, Brazil, Canada, China, France, Germany, India,
Indonesia, Ireland, Italy, Japan, Korea, Malaysia, Mexico, the Netherlands,
New Zealand, Norway, Poland, Puerto Rico, Russia, Singapore, South Africa, Spain,
Sweden, Switzerland, Taiwan, Thailand, United Kingdom, the United States and Venezuela.
Distributors are located in all major industrial areas of the world.
Because of developments in technology these data or procedures may be subject to change. Consequently we advise
users to review their continuing validity annually.
, Pall, SUPRAdisc and SUPRAdur are trade marks of Pall Corporation.
Filtration. Separation. Solution. is a service mark of Pall Corporation.
Part Numbers quoted above are protected by the Copyright of Pall Europe Limited.
® indicates a trademark registered in the USA.
© 2004, Pall Europe Limited.
10.2004