BP90 Owner's Manual-English - Digitech

More documents

Recommendations

Info

32 Expression assignments available are as follows: No Assignment OF Volume Pr (Output Level Pre Delay) Volume PS (Output Level Post Delay) Wah AH (Expression Pedal acts as a Wah pedal) Amp A (Expression Pedal controls the Amp Gain) Chorus SP (Speed) LE (Level) Flanger SP (Speed) LE (Level) Phaser SP (Speed) LE (Level) Tremolo SP (Speed) dP (Depth) Panner SP (Speed) dP (Depth) Vibrato SP (Speed) dP (Depth) Octavider OL (Octavider level) Envelope Filter ES (Sensitivity) YaYa Pd (Expression Pedal acts as a YaYa TM Effect when engaged) AutoYa SP (Speed) dP (Depth) Detune LE (Level of the Detuned signal) Pitch Shift LE (Level of the Pitch Shifted signal) Whammy HY (Expression Pedal acts as a DigiTech ® Whammy TM pedal) Delay dL (Delay Level) dF (Delay Feedback) Reverb rL (Reverb Level)
Drum Machine The BP90 features a built-in drum machine, which is enabled by pressing the Drums button. Select patterns, tempo, and level with the Edit Up/Down buttons. Change their values with the Value Up/Down buttons. The drum machine has the following parameters Drum Patterns 1-40 Drum Tempo 1-99 (equivalent of 40 – 240BPM) Drum Level 0-99 Drum machine settings are globally set and not individually stored with each of the BP90’s user presets. Factory Reset This function resets the BP90 to its original factory settings. This procedure erases all custom User presets. ATTENTION: Performing this function will erase all user-programmed data. All such data will be lost forever! Be sure you want to erase the memory and return the BP90 to its factory default state before continuing with this procedure. The procedure for performing a Factory Reset is as follows: 1. Press and hold the Store button while powering up the BP90. 2. When the display prompts you with FR, release the Store button. 3. Press and hold the Store button for 3 seconds until RS appears in the display and release. The Factory Reset procedure takes approximately 10 seconds. 4. Once the factory reset has finished you will need to calibrate the Expression Pedal. Follow steps 2-4 on the next page to complete calibration. 33
Page 1 and 2: Modeling Bass Processor Professiona
Page 3 and 4: Manufacturer’s Name: DigiTech Man
Page 5 and 6: Table of Contents Section One - Int
Page 7 and 8: Section 1 - Introduction Getting Ac
Page 9 and 10: up. The right 6 red LEDs indicate t
Page 11 and 12: Value Buttons NOISE GATE EQUALIZER
Page 13 and 14: 1. Footswitches These two Footswitc
Page 15 and 16: 4. Value Up/Down The Value Up/Down
Page 17 and 18: 4. Headphones Connect a pair of ste
Page 19 and 20: Stereo Operation For stereo operati
Page 21 and 22: Applying Power Before applying powe
Page 23 and 24: Anytime a stored value within a pre
Page 25 and 26: Section Three - Models and Effects
Page 27 and 28: Compressor A Compressor is used to
Page 29 and 30: Distortion Models f1-f9 DigiFuzz Fu
Page 31 and 32: Chorus A Chorus adds a short delay
Page 33 and 34: Detune A Detuner makes a copy of yo
Page 35 and 36: Delay Variation OF Delay effect is
Page 37: Section Four - Other Functions Expr
Page 41 and 42: Section 5 - Appendix Specifications
Page 43 and 44: Tone Library Display Name Display N
Page 48: DigiTech ® 8760 South Sandy Parkwa

BP90 Owner's Manual-English - Digitech

Create successful ePaper yourself

Delete template?

Save as template?