OM, 2348 LS, (CA), 96043004900, 2008-03, Ride Mower - Husqvarna

More documents

Recommendations

Info

SERVICE AND ADJUSTMENTS TO LEVEL MOWER Make sure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly. VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig. 24) • With all tires properly inflated and if your lawn appears unevenly cut, determine which side of mower is cutting lower. • With a 3/4" or adjustable wrench, turn lift link adjustment nut (A) to the left to lower LH side of mower, or, to the right to raise LH side of mower. Turn nut right to raise mower NOTE: Each full turn of adjustment nut will change mower height about 3/16". • Test your adjustment by mowing some uncut grass and visually checking the appearance. Readjust, if necessary, until you are satisfied with the results. PRECISION SIDE-TO-SIDE ADJUSTMENT (See Fig. 25) • With all tires properly inflated, park tractor on level ground or driveway. CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth. • Raise mower to its highest position. • At both sides of mower, position blade at side and measure the distance (A) from bottom edge of blade to the ground. The distance should be the same on both sides. A 02948 A FIG. 24 02966 FIG. 25 Turn nut left to lower mower A 21 • If adjustment is necessary, see step in Visual Adjustment instructions above. • Recheck measurements, adjust if necessary until both sides are equal. FRONT-TO-BACK ADJUSTMENT (See Figs. 26 and 27) IMPORTANT: Deck must be level side-to-side. To obtain the best cutting re sults, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position. CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth. • Raise mower to highest position. • Position any blade so the tip is pointing straight forward. Measure distance (B) to the ground at front and rear tip of the blade. • If front tip of blade is not 1/8" to 1/2" lower than the rear tip, go to the front of tractor. B B FIG. 26 • With an 11/16" or adjustable wrench, loosen jam nut A several turns to clear adjustment nut B. • With a 3/4" or adjustable wrench, turn front link adjustment nut (B) clockwise (ltighten) to raise the front of mower, or, counterclockwise (loosen) to lower the front mower. Tighten adjust nut B to raise mower 02950 FIG. 27 NOTE: Each full turn of the adjustment nut will change mower height about 1/8". • Recheck measurements, adjust if necessary until front tip of blade is 1/8" to 1/2" lower than the rear tip. • Hold adjustment nut in position with wrench and tighten jam nut securely against adjustment nut. B Loosen jam nut A first 02548 A Loosen adjust nut B to lower mower
K L P R SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT(See Fig. 28) MOWER DRIVE BELT REMOVAL • Park tractor on a level surface. En gage parking brake. • Lower attachment lift lever to its lowest position. • Disengage belt tension rod (K) from lock bracket (L). CAUTION: Belt tension rod is spring loaded. Have a firm grip on rod and release slowly. • Remove screws (P) from mandrel covers (Q) and remove covers. • Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface. • Remove belt from electric clutch pulley (M), both mandrel pulleys (R) and all idler pulleys (S). R S Q M R FIG. 28 22 MOWER DRIVE BELT INSTALLATION • Install belt around all mandrel pulleys (R) and around idler pulleys (S) as shown. • Install belt onto electric clutch pulley (M). IMPORTANT: Check belt for proper routing in all mower pulley grooves. • Reassemble mandrel covers (Q). Securely tighten all screws. • Engage belt tension rod (K) on locking bracket (L). CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly. • Raise attachment lift lever to highest position. P Q
Page 1: Ride Mower 2348 LS (CA) 96043004900
Page 4 and 5: III. CHILDREN Tragic accidents can
Page 6 and 7: Key (2) Keys UNASSEMBLED PARTS (1)
Page 8 and 9: OPERATION These symbols may appear
Page 10 and 11: OPERATION The operation of any trac
Page 12 and 13: TO OPERATE MOWER (See Fig. 9) Your
Page 14 and 15: PURGE TRANSMISSION CAUTION: Never e
Page 16 and 17: TRACTOR Always observe safety rules
Page 18 and 19: NOTE: Although multi-viscosity oils
Page 20 and 21: 02965 02965 SERVICE AND ADJUSTMENTS
Page 24 and 25: SERVICE AND ADJUSTMENTS TO REPLACE
Page 26 and 27: SERVICE AND ADJUSTMENTS REPLACING B
Page 28 and 29: TROUBLESHOOTING POINTS PROBLEM CAUS
Page 30 and 31: TRACTOR - - MODEL NUMBER 2348LS (96
Page 46 and 47: 1. Fold this page along dotted line
Page 48 and 49: SERVICE NOTES 47
Page 50: starter ropes and tiller tines; (2)

OM, 2348 LS, (CA), 96043004900, 2008-03, Ride Mower - Husqvarna

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?