The Paint Manual - Hempel

More documents

Recommendations

Info

Clean & Shine Concentrated wash and wax that effectively cleans, shines and leaves a protective coating in one application. For use on all surfaces. Dilute 1 part Clean & Shine with 10 parts fresh or sea water for heavy cleaning. Up to 50 parts for general cleaning. Apply with a sponge, soft brush or cloth, rinse with fresh water. Minimum application temperature: 5°C/40°F Gelcoat Cleaning Spray Quick and easy-to-use foaming cleaner spray, for removing marks and stains over large areas. Use only on gelcoat and painted surfaces. Particularly good for cleaning deposits from the waterline. Chemical process avoids the need to rub or scrub the surface. Spray foam onto surface and leave for 10 to 15 minutes, wash off with freshwater. Use Cleaning Gel for tough stubborn stains. Minimum application temperature: 5°C/40°F Gelcoat Cleaning Gel High strength, non-abrasive cleaning gel for removing rust & exhaust stains, waterline deposits, fender and other marks over small/local areas. Use only on gelcoat and painted surfaces. Does not run when applied to vertical surfaces. Chemical process avoids the need to rub or scrub the surface. Apply by brush, leave for 15 to 30 minutes, wash off with freshwater, brushing if necessary. Minimum application temperature: 5°C/40°F Gelcoat Cleaning Powder Strong, fine abrasive cleaning powder for removing tough deposits, stains and yellowing. Use only on gelcoat surfaces. Removes hull discolouration from soil deposits in fresh or brackish water. Particularly suitable for cleaning large areas such as non-slip decks where dirt accumulates. Mix Gelcoat Cleaning Powder with enough freshwater to make a paste. Apply evenly onto gelcoat which has been wetted with fresh water. Leave for 10-20 minutes. Use a soft brush to clean while paste is still moist.Thoroughly hose down with fresh water before the paste hardens. comes with a trigger New name New name 1 ltr 500 ml 500 ml 750 ml 67 Boatcare
68 Boatcare Rubbing Liquid Fine abrasive rubbing compound to remove oxidisation and light scratch marks from most surfaces, including aluminium. Restores and renews the gloss and colour to gelcoat and painted surfaces. Apply with a soft cloth, rub by hand or with a polishing machine, wipe away any residue with a clean cloth. Minimum application temperature:: 5°C/40°F. WaxTecCel High performance liquid wax with TecCel technology, for a long lasting, deep gloss, tough protective finish on gelcoat, painted and varnished surfaces. Apply with a soft cloth, polish by hand or with a polishing machine, allow to dry for 5–10 minutes, polish away any residue with a clean cloth leaving a high gloss mirror like finish. Minimum application temperature: 5°C/40°F. Wax Liquid wax for use on gelcoat, painted and varnished surfaces, leaving an extremely glossy UV protective finish. Apply with a soft cloth, polish by hand or with a polishing machine, allow to dry for 5–10 minutes, polish then wipe away any residue with a clean cloth leaving a high gloss finish. Minimum application temperature: 5°C/40°F. New name New name New name 500 ml 500 ml 500 ml
Page 2 and 3:
Contents Thank you for choosing Hem
Page 4 and 5:
Preparing to paint • Planning the
Page 6 and 7:
Temperature and humidity Our paints
Page 8 and 9:
Hearing Body Feet Head What are the
Page 10 and 11:
2. Cleaning and degreasing Good sur
Page 12 and 13:
Wet Abrading Due to the lubricating
Page 14 and 15:
Application methods and tools There
Page 16 and 17:
An important part of choosing the r
Page 18 and 19: Painting advice and specifications
Page 20 and 21: Fill along boottop Fairing any defe
Page 22 and 23: Repainting all substrates Maintaini
Page 24 and 25: Painting substrates Glassfibre Glas
Page 26 and 27: Ferrocement Ferrocement is a specia
Page 28 and 29: Steel - single pack/conventional Pr
Page 30 and 31: Varnishing wood Wood is a naturally
Page 32 and 33: Wood - single pack system/conventio
Page 34 and 35: Wood - varnish Product No of coats
Page 36 and 37: Keels Keels are made from steel, ca
Page 38 and 39: Outdrives Product No of coats Recoa
Page 40 and 41: Osmosis • What is osmosis and how
Page 42 and 43: Osmosis protection When to use an o
Page 44 and 45: Osmosis treatment When to use an os
Page 46 and 47: Using Gel/High Protect How to apply
Page 48 and 49: Our products • Primers and underc
Page 50 and 51: Antifouling Primer A single compone
Page 52 and 53: SUBSTRATE SUBSTRATE PRIMERS Glassfi
Page 54 and 55: Antifoulings and bottom coats Fouli
Page 56 and 57: Applying antifouling Applying Hard
Page 58 and 59: Tiger Xtra Self polishing, erodible
Page 60 and 61: What antifouling should I use? Type
Page 62 and 63: MultiCoat A single component semi-g
Page 64 and 65: Dura-Gloss Varnish/Dura-Satin Varni
Page 66 and 67: Thinners It’s important you only
Page 70 and 71: RIB Clean Powerful, concentrated, s
Page 72: Mildew Remover An easy-to-use produ
Page 75 and 76: 74 Calculating areas to be overcoat
Page 77 and 78: 76 Health and safety Health and Saf
Page 79 and 80: 78 Trouble shooting Fault Causes Wh
Page 81 and 82: 80 Technical terms Levelling Abilit
show all

The Paint Manual - Hempel

Create successful ePaper yourself

Delete template?

Save as template?