Views
5 years ago

HEMPEL HEMPEL'S EPOXY KNIFING FILLER 355SA

HEMPEL HEMPEL'S EPOXY KNIFING FILLER 355SA

HEMPEL'S EPOXY KNIFING FILLER 355SA SURFACE The surface must be sound and free from dust, loose paint, oil/grease and other contaminants. PREPARATION: Metal: Remove oil and grease, etc. with suitable detergent. Remove salt and other contaminants by (high pressure) fresh water cleaning. Abrasive blasting, power tool cleaning or sanding, depending on material and condition of the surface. Finally clean the area with HEMPEL’S THINNER 08450. Priming after abrasive blast cleaning, but prior to filling, can be done with a thin layer of e.g. HEMPADUR 15590. Concrete: Remove slip agent and other possible contaminants by emulsion washing followed by high pressure hosing with fresh water. Remove scum layer and loose matter to a hard, rough and uniform surface, preferably by abrasive blasting, possibly by other mechanical treatment or acid etching. Seal surface with suitable sealer, e.g. HEMPADUR SEALER 05990, prior to filling. APPLICATION Use only where application and curing can proceed at temperatures above 5°C/41°F. CONDITIONS: The temperature of the substrate should also be above this limit. Apply only on a dry and clean surface with a temperature above the dew point to avoid condensation. PRECEDING None, or according to specification. COAT: SUBSEQUENT According to specification. COAT: REMARKS: Mix and stir the two components thoroughly until an even colour is achieved, whereafter the filler is ready for use. Do not mix more than is necessary for use within the pot life. If the maximum recoating interval is exceeded, roughening of the surface is necessary to ensure intercoat adhesion. May be sanded after 20 hours (20°C/68°F). Note: HEMPEL’S EPOXY KNIFING FILLER 355SA is for professional use only. ISSUED BY: HEMPEL PAINTS (SAUDI ARABIA) W.L.L. - 355SA3010SSA004 This Product Data Sheet supersedes those previously issued. For explanations, definitions and scope, see “Explanatory Notes” in the HEMPEL Book. Data, specifications, directions and recommendations given in this data sheet represent only test results or experience obtained under controlled or specially defined circumstances. Their accuracy, completeness or appropriateness under the actual conditions of any intended use of the Products herein must be determined exclusively by the Buyer and/or User. The Products are supplied and all technical assistance is given subject to HEMPEL's GENERAL CONDITIONS OF SALES, DELIVERY AND SERVICE, unless otherwise expressly agreed in writing. The Manufacturer and Seller disclaim, and Buyer and/or User waive all claims involving, any liability, including but not limited to negligence, except as expressed in said GENERAL CONDITIONS for all results, injury or direct or consequential losses or damages arising from the use of the Products as recommended above, on the overleaf or otherwise. Product data are subject to change without notice and become void five years from the date of issue. Issued: January 2005 Page 2 of 2 2/2 Product Data Sheet

A Challenge for the Steel Builder and Paint Applicator ... - Hempel
A journey through Hempel's - Hempel World
Marine colour card - Hempel
Code of Conduct - Hempel
Newsletter in English.pdf - Hempel
Coating Reference Handbook - Hempel
WATERBORNE COATING SYSTEMS - Hempel
Hempel's Globic Antifouling System - ShipServ
Hempel Colour Chart.pdf - Mailspeed Marine
Hot air knife - Maag
The Blinding Knife (Lightbringer) (Brent Weeks)
Win a trip to New York New Intumescent coatings from Hempel
Brazing filler metals • Soft solder alloys Copper filler metals
Epoxy Application Guide - Loctite.ph
CERAMENT™|BONE VOID FILLER - Bonesupport
Hempel and the Environment - C3P
Who's got the Best Riving Knife? - Shark Guard
Filler Parts PDF - Rubber Fab Mold and Gasket
Pollen: A Novel, Biorenewable Filler for Polymer ... - Meredith Group
Expert Tips to Clean and Maintain Epoxy Floors
See what you are doing and leave a dry field! - SWISS KNIFE
Code of Conduct - Hempel
HEMPADUR EM 35740 - Hempel
The universal vacuum filler RS 105 Insaccatrice universale RS 105
BascoPrime 2-component filler, colourless 53-0007 ... - Finres Group