Product Data Sheet - Hempel

Description:
Recommended use:
Availability:
PHYSICAL CONSTANTS:
Product Data
HEMPEL'S WATER GLIDE 74500
HEMPEL'S WATER GLIDE 74500 is a fast drying, thin-film antifouling product containing high amount
of copper and TecCel which assures a smooth surface reducing the friction for maximum speed. It is an
ideal product for yachting (regatta).
It is possible to launch shortly after painting.
As an antifouling for power, speed and racing boats of glass fibre, wood and steel.
Do not use on aluminium or light alloy metals due to risk of corrosion in case of direct contact.
Not suitable for Mediterranean region.
Part of European Yacht assortment. Local availability subject to confirmation.
Shade nos/Colours:
Finish: Flat
Volume solids, %: 10 ± 1
Theoretical spreading rate: 10 m2 51560*/ Copper
/l [401 sq.ft./US gallon] - 10 micron/0.4 mils
Flash point:
25 °C [77 °F]
Specific gravity:
1.2 kg/litre [10.1 lbs/US gallon]
Dry to touch: 20 minute(s) (approx.) at 20°C/68°F
40 minute(s) (approx.) at 10°C/50°F
VOC content:
764 g/l [6.3 lbs/US gallon]
-
-
*other shades according to assortment list.
APPLICATION DETAILS:
Application method: Conventional spray Brush/Roller
Thinner (max.vol.): 08081 (20%) 08081 (10%)
Nozzle orifice: 0.047 - 0.063 "
Nozzle pressure: 4.5 bar [65.2 psi]
Cleaning of tools:
The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.
HEMPEL'S THINNER 08081
Indicated film thickness, dry: 10 micron [0.4 mils] see REMARKS overleaf.
Indicated film thickness, wet: 90 micron [3.6 mils]
Recoat interval, min: According to specification.
Recoat interval, max: According to specification.
Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,
consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.
Date of issue: March 2012
-
Page: 1/2
Product Data Sheet

HEMPEL'S WATER GLIDE 74500
SURFACE PREPARATION: Existing thin film antifouling: Wash thoroughly with fresh water (light wet grinding if necessary). Allow
the surface to dry. Apply 3 coats of the product.
Existing old antifouling: Wet grinding the surface to remove loose material. Wash thorougly with fresh
water. Allow the surface to dry. Apply 3 coats of the product.
Old self-polishing antifouling and Glide Speed: Remove old antifouling with HEMPEL'S PAINT
STRIPPER 99540/ wet grinding followed by (high pressure) fresh water pressure. Allow the surface to
dry before coating. Apply 1-2 coats HEMPEL'S LIGHT PRIMER 45551 depending on condition of
existing primer.Apply 3 coats of the product.
Not treated surface: Remove oil and grease with suitable detergent. Wash thoroughly with fresh water.
Allow the surface to dry. Apply: HEMPEL'S LIGHT PRIMER 45551. According to separate
APPLICATION INSTRUCTIONS. Apply 3 coats of the product.
APPLICATION CONDITIONS: The surfaces to be treated must be clean and dry and free from grease and oil. Apply only on a dry and
clean surface with a temperature above the dew point to avoid condensation. Do not apply in direct
sunlight.
In confined spaces provide adequate ventilation during application and drying.
PRECEDING COAT According to specification. Recommended systems are: HEMPEL'S LIGHT PRIMER 45551
REMARKS: This product contains heavy particles. Stir well before use.
Film thicknesses/thinning: Keep thinning to a minimum to ensure that correct film thickness is obtained.
Undocking:
Can be launched after minimum 2 hours drying at 23°C.
After painting, the product can be left out of water for up to: 6 months. Discolouration may occur.
Recoating note: Recommended number of coats: 3 coats approximately 30 micron dry film thickness
Care must be taken to apply material in order to achieve the specified dry film thickness.
Note:
HEMPEL'S WATER GLIDE 74500 The information given in the Product Data Sheet is intended for
commercial use.
ISSUED BY: HEMPEL A/S 7450051560
This Product Data Sheet supersedes those previously issued.
For explanations, definitions and scope, see “Explanatory Notes” available on www.hempel.com. Data, specifications, directions and recommendations given in this data sheet represent only test results
or experience obtained under controlled or specially defined circumstances. Their accuracy, completeness or appropriateness under the actual conditions of any intended use of the Products herein
must be determined exclusively by the Buyer and/or User.
The Products are supplied and all technical assistance is given subject to HEMPEL's GENERAL CONDITIONS OF SALES, DELIVERY AND SERVICE, unless otherwise expressly agreed in writing.
The Manufacturer and Seller disclaim, and Buyer and/or User waive all claims involving, any liability, including but not limited to negligence, except as expressed in said GENERAL CONDITIONS for all
results, injury or direct or consequential losses or damages arising from the use of the Products as recommended above, on the overleaf or otherwise. Product data are subject to change without notice
and become void five years from the date of issue.
Date of issue: March 2012
-
Page: 2/2
Product Data Sheet