KOMET KUB Pentron™ - Solid drilling to 5 × D - komet group

More documents

Recommendations

Info

KOMET KUB Pentron Inserts W80..01 (SOGX) Application range Solid drilling BK84 5: Allrounder, steel, stainless steel, cast iron BK 7 0: Stainless steel BK64 5: steel, stainless steel BK6115: Cast iron, steel, stainless steel HPC type BK7710: Non ferrous metals BK6115 BK64 5 BK 7 0 BK7710 BK84 5 l R H __ Carbide grades ISO-Code Order No. CVD PVD coated coated enter carbide code 6115 6425 2730 7710 8425 SOGX 060 06-01 W80 18010.06.. G G G G G 6, 0,6 SOGX 07T 08-01 W80 20010.08.. G G G G G 7,1 0,8 SOGX 080 08-01 W80 24010.08.. G G G G G 8,0 0,8 Mild steel / tool steel P Order example: Stainless and acid-resistant steel M Grey cast iron, spheroidal cast iron K Non ferrous metals N Heat-resistant steels S ISO-Code SOGX 060 06-01 Carbide grade BK64 5 Order No. Hardened tool steel H W80 18010.0664 5 Alternative Inserts for higher cutting speed 10 xD 18,5 – 0,0 0,5 – ,0 ,5 – 6,0 $ § § $ § § § § $ $ $ § $ $ $ W80 18010.066425 W80 18010.066115 W80 20010.086425 W80 20010.086115 W80 24010.086425 W80 24010.086115 R Cutter geometry Note: Insert W80..01 in BK6115 is NOT suitable for use as an internal cutting edge for solid drilling. for higher cutting speed Order No. ISO-Code size Note: Only use this insert with KUB Pentron TM as an external cutting edge: SOGX ... -01 (geometry 01) in BK6115 SOGX 060 06-01 BK64 5 SOGX 060 06-01 BK6115 SOGX 07T 08-01 BK64 5 SOGX 07T 08-01 BK6115 SOGX 080 08-01 BK64 5 SOGX 080 08-01 BK6115 l P M K N S H $ $ $ $ $ $ Topography Inscribed circle
KOMET KUB Pentron Technical Notes 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 1 2 3 Starting on uneven surfaces (cast surfaces) - when inserting and withdrawing the drill, reduce the feed rate by approx. 0-50% (depending on component stability, clamping and surface quality) Starting on angled surfaces / angled bore exit - when inserting the drill, reduce the feed rate by approx. 0-60% until full diameter is reached - when withdrawing the drill after interruption to the cut, reduce the feed rate by approx. 0-60% - use tough insert and stable corner radius Starting on cambered surfaces - when inserting the drill, reduce the feed rate by approx. 0-60% until full diameter is reached - when withdrawing the drill after interruption to the cut, reduce the feed rate by approx. 0-60% (depending on component stability and clamping). Drilling through a cross bore - when inserting and withdrawing the drill, reduce the feed rate by approx. 0-50% (depending on component stability, clamping and surface quality) - in the vicinity of the cross bore, reduce the feed rate by 50% - watch for chip jamming around tool - use tough insertand stable corner radius Drilling a chamber - first bore Nos. 1 + , then bore No. - check distribution is symmetrical - avoid chip jams - use tough insertand stable corner radius - Continuous drilling: when inserting the drill, reduce the feed rate by approx. 0-60% (depending on component stability and clamping) - Interruption to cut: when drilling the cut interruption, reduce the feed rate by approx. 50-60% Starting on a groove or large centering bore - when inserting the drill, reduce the feed rate by approx. 0-50% until centring depth is reached - reduce feed rate - use tough insert for internal cutting edge - spot face if required Starting on an edge - when inserting and withdrawing the drill, reduce the feed rate by approx. 0-50% (depending on component stability, clamping and surface quality) - use tough insert and stable corner radius Starting on a welded seam - when inserting the drill, reduce the feed rate by approx. 0-60% until full diameter is reached - when withdrawing the drill after interruption to the cut, reduce the feed rate by approx. 0-60% (depending on component stability and clamping). Drilling through stacked plates - good workpiece clamping required - max. gap = 1 mm Roughing - not possible adjustable - when inserting and withdrawing the drill reduce the feed rate by approx. 0-50% until full bore diameter is reached (depending on component stability and clamping). - use tough insert and stable corner radius Note: The application details shown depend on the environmental and application conditions (e.g. machine, ambient temperature, use of lubricant/coolant and the machining result required). These are subject to correct operating conditions, correct application and compliance with the spindle speed limits given for the tools. 11
Page 1 and 2: KOMET KUB Pentron Solid drilling to
Page 3 and 4: KOMET KUB Pentron TM continuous dri
Page 5 and 6: xD -0,1/+0, 4×D 5×D $ $ & $ X $ $
Page 7 and 8: xD -0,1/+0, 4×D 5×D $ $ & $ X $ $
Page 9: 4×D 5×D x18,5- 19,0 x19,1- 0,0 x

KOMET KUB Pentron™ - Solid drilling to 5 × D - komet group

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?