Template BA B168xH238

ENGLISH
If you want to abort the process:
▶ Briefly press the P button.
The display shows nn.
Note:
There is a danger of being locked out if no fingerprints are
stored in the finger-scan.
8.3.4 Menu 20: Assign relay
Each stored fingerprint can be assigned to one of the two
relays.
This function is not called up if no fingerprints have been
stored and you go directly back to the nn display.
1. Select menu 20.
The display for the first occupied memory
space will appear (e.g. 0.0).
2. Select the desired memory space using
the ñ ò buttons.
This will only show the occupied memory
spaces.
As standard, the memory space is assigned
to relay 1. This is indicated by an illuminated
decimal point in the left 7-segment display.
3. Press the P button and hold it for 4 seconds.
The relay is changed.
If relay 2 is assigned, this is indicated by an
illuminated decimal point in the right
7-segment display (e.g. 00.).
If you want to abort the process:
▶ Briefly press the P button.
The display shows nn.
8.3.5 Menu 21: Impulse duration relay 1
The length of the control impulse for relay 1 can be set by
selecting menu 21.
1. Select menu 21.
The decimal point on the left 7-segment
display is illuminated.
2. Select the desired impulse length using the
buttons ñ ò (see table).
3. Press the P button and hold it for 4 seconds.
The selected value is confirmed.
Display Impulse duration FS
d.0 0.5 seconds (delivery condition)
d.1 1 second
d.2 2 seconds
d.3 5 seconds
d.4 10 seconds
d.5 20 seconds
d.6 30 seconds
d.7 45 seconds
d.8 60 seconds
d.9 90 seconds
If you want to abort the process:
▶ Briefly press the P button.
The display shows nn.
8.3.6 Menu 22: Impulse duration relay 2
The length of the control impulse for relay 2 can be set by
selecting menu 22.
1. Select menu 22.
The decimal point on the right 7-segment
display is illuminated.
2. Select the desired impulse length using the
buttons ñ ò (see table).
3. Press the P button and hold it for 4 seconds.
The selected value is confirmed.
Display Impulse duration FS
d0. 0.5 seconds (delivery condition)
d1. 1 second
d2. 2 seconds
d3. 5 seconds
d4. 10 seconds
d5. 20 seconds
d6. 30 seconds
d7. 45 seconds
d8. 60 seconds
d9. 90 seconds
If you want to abort the process:
▶ Briefly press the P button.
The display shows nn.
8.3.7 Menu 30: Security setting
You can select between the security settings Standard and
High with menu 30.
Standard is the factory setting and is indicated
by the S0 display.
The High setting is indicated by the S1 display.
The High setting demands a very high agreement
in the comparison with the stored fingerprint.
Change security setting:
▶ Press the P button and hold it for 4 seconds.
The security setting has been changed and is shown
accordingly.
If you want to exit the menu or abort the process:
▶ Briefly press the P button.
The display shows nn.
8.3.8 Menu 31: Activate/change access code
The 4-digit access code can be activated/deactivated or
changed by selecting menu 31.
In the delivery condition, the access code is deactivated,
i.e. set to 0000. When the access code is 0000, unimpeded
access to the menu selection and function settings is
possible. If an access code is set that is different from 0000,
you must first enter this PIN before you can make a menu
selection.
Note:
If you have forgotten your access code, the finger-scan can
only be made functional again at the factory through a
so-called factory reset.
TR30G008-D RE / 12.2009 17