Rompevirutas Torneado - korloy

Match DrillsGMSD-P/M/K/NTerminologiaRecubrimientoP M KNCarburo cementadoTolerancia(Diametro Broca)Tolerancia(Dam. zanco)h7h6Angulo punta 140° 135°Angulo de giroReduccionRefrigerante30°X TipoExternoP Acero M Acero Inoxidable K Fundicion N Metales No-ferrosos(mm)CódigoØDØd3P,M,K,N 5P,M,K,N 7P,M,K,NL L LMSD113- P,M,K,N114- P,M,K,N115- P,M,K,N116- P,M,K,N117- P,M,K,N118- P,M,K,N119- P,M,K,N120- P,M,K,N121- P,M,K,N122- P,M,K,N123- P,M,K,N124- P,M,K,N125- P,M,K,N126- P,M,K,N127- P,M,K,N128- P,M,K,N129- P,M,K,N130- P,M,K,N131- P,M,K,N132- P,M,K,N133- P,M,K,N134- P,M,K,N135- P,M,K,N136- P,M,K,N137- P,M,K,N138- P,M,K,N139- P,M,K,N140- P,M,K,N141- P,M,K,N142- P,M,K,N143- P,M,K,N144- P,M,K,N145- P,M,K,N146- P,M,K,N147- P,M,K,N148- P,M,K,N149- P,M,K,N150- P,M,K,N151- P,M,K,N152- P,M,K,N153- P,M,K,N154- P,M,K,N155- P,M,K,N156- P,M,K,N11.311.411.511.611.711.811.912.012.112.212.312.412.512.612.712.812.913.013.113.213.313.413.513.613.713.813.914.014.114.214.314.414.514.614.714.814.915.015.115.215.315.415.515.612.012.012.012.012.012.012.012.013.013.013.013.013.013.013.013.013.013.014.014.014.014.014.014.014.014.014.014.015.015.015.015.015.015.015.015.015.015.016.016.016.016.016.016.06060606060606060656565656565656565657070707070707070707075757575757575757575808080808080118118118118118118118118125125125125125125125125125125132132132132132132132132132132139139139139139139139139139139146146146146146146909090909090909098989898989898989898105105105105105105105105105105108108108108108108108108108108112112112112112112148148148148148148148148158158158158158158158158158158167167167167167167167167167167172172172172172172172172172172178178178178178178114114114114114114114114124124124124124124124124124124133133133133133133133133133133138138138138138138138138138138144144144144144144172172172172172172172172184184184184184184184184184184195195195195195195195195195195202202202202202202202202202202210210210210210210Brocas SolidasBrocas Código de pedido : MSD-Material (P,M,K,N) × Largo de flarta - Largo toral L × diámerto de zanco SEx.1) Material : SM45C, Diámetro a maquinar : Ø10.1mm, Largo de flauta : 60mm, Largo total : 80mm, Diámetro de zanco : Ø11MSD101-P × 60 - 80L × 11SEx.2) Material : STS303, Diámetro a maquinar : Ø10.12mm, Largo de flauta : :60mm, Largo total : 80mm, Diámetro de zanco : Ø11MSD1012 - M × 60 - 80L × 11SG37