Rompevirutas Torneado - korloy

GMatch DrillsMSD-P/M/K/NTerminologiaRecubrimientoP M KNCarburo cementadoTolerancia(Diametro Broca)Tolerancia(Dam. zanco)h7h6Angulo punta 140° 135°Angulo de giroReduccionRefrigerante30°X TipoExternoP Acero M Acero Inoxidable K Fundicion N Metales No-ferrosos(mm)CódigoØDØd3P,M,K,N 5P,M,K,N 7P,M,K,NL L LBrocas SolidasBrocasMSD157- P,M,K,N158- P,M,K,N159- P,M,K,N160- P,M,K,N161- P,M,K,N162- P,M,K,N163- P,M,K,N164- P,M,K,N165- P,M,K,N166- P,M,K,N167- P,M,K,N168- P,M,K,N169- P,M,K,N170- P,M,K,N171- P,M,K,N172- P,M,K,N173- P,M,K,N174- P,M,K,N175- P,M,K,N176- P,M,K,N177- P,M,K,N178- P,M,K,N179- P,M,K,N180- P,M,K,N181- P,M,K,N182- P,M,K,N183- P,M,K,N184- P,M,K,N185- P,M,K,N186- P,M,K,N187- P,M,K,N188- P,M,K,N189- P,M,K,N190- P,M,K,N191- P,M,K,N192- P,M,K,N193- P,M,K,N194- P,M,K,N195- P,M,K,N196- P,M,K,N197- P,M,K,N198- P,M,K,N199 - P,M,K,N200- P,M,K,N15.715.815.916.016.116.216.316.416.516.616.716.816.917.017.117.217.317.417.517.617.717.817.918.018.118.218.318.418.518.618.718.818.919.019.119.219.319.419.519.619.719.819.920.016.016.016.016.017.017.017.017.017.017.017.017.017.017.018.018.018.018.018.018.018.018.018.018.019.019.019.019.019.019.019.019.019.019.020.020.020.020.020.020.020.020.020.020.08080808085858585858585858585858585858585858585858888888888888888888890909090909090909090146146146146151151151151151151151151151151153153153153153153153153153153157157157157157157157157157157160160160160160160160160160160112112112112120120120120120120120120120120120120120120120120120120120120124124124124124124124124124124130130130130130130130130130130178178178178186186186186186186186186186186188188188188188188188188188188193193193193193193193193193193200200200200200200200200200200144144144144153153153153153153153153153153162162162162162162162162162162171171171171171171171171171171180180180180180180180180180180210210210210220220220220220220220220220220230230230230230230230230230230240240240240240240240240240240250250250250250250250250250250G38 Código de pedido : MSD-Material (P,M,K,N) × Largo de flarta - Largo toral L × diámerto de zanco SEx.1) Material : SM45C, Diámetro a maquinar : Ø10.1mm, Largo de flauta : 60mm, Largo total : 80mm, Diámetro de zanco : Ø11MSD101-P × 60 - 80L × 11SEx.2) Material : STS303, Diámetro a maquinar : Ø10.12mm, Largo de flauta : :60mm, Largo total : 80mm, Diámetro de zanco : Ø11MSD1012 - M × 60 - 80L × 11S