Instruction Manual - Service - Black & Decker

More documents

Recommendations

Info

• Allow the tool to build up speed before plunging down into the workpiece. When the depth stop bar has been contacted, operate the plunge lock lever (5). • Carry out the operation by applying a constant force both downwards and in the direction of cut. Retain a firm grip on the handles and be prepared for a possible reaction force if the router bit suddenly stalls e.g. following contact with a knot. • On completion of the operation, release the plunge lock lever and control the upwards movement of the tool back to its original position. When the tool has returned to its original position, it can be switched off. Be aware that the base is springloaded and that the tool will jump upwards if not controlled. Routing speed The operating speed of the tool can be varied to affect the level of finish. The correct speed selection will depend upon the level of finish required, the type of material being machined, the diameter and shape of the router bit. • Prepare the tool to make a practice cut on a piece of scrap material. Make a preliminary adjustment of the speed control selecting a high speed for small diameter router bits and a low speed for large diameter router bits. • When the routing operation is completed, withdraw the tool from the workpiece, switch off the tool and inspect the level of finish. Adjust the speed control knob (4) and repeat until an optimum level of finish is obtained. Warning! Do not release the handles to adjust the speed when the tool is locked down and operating in the workpiece. 14 ENGLISH Hints for optimum use • When working on outside edges, move the tool counterclockwise (fig. N). When working on inside edges, move the tool clockwise. • Use HSS router bits for softwood. • Use TCT router bits for hardwood. • You can use the tool without a guide (fig. O). This is useful for signwriting and creative work. Only make shallow cuts. • Refer to the table below for common types of router bits. KW1600EA - Router bits (fig. P) Description Application Straight bit (1) Grooves and rebates Trimming bit (2) Trimming laminates or hardwood; accurate profiling using a template Rebating bit (3) Rebates on straight or curved workpieces V-grooving bit (4) Grooves, engraving and edge bevelling Core box bit (5) Fluting, engraving and decorative edge moulding Cove bit (6) Decorative edge moulding Ogee moulding bit (7) Decorative edge moulding Rounding over bit (8) Rounding over edges Dovetail bit (9) Dovetail joints Chamfer bit (10) Chamfer edges
Maintenance Your tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning. Warning! Before performing any maintenance, switch off and unplug the tool. • Regularly clean the ventilation slots in your tool using a soft brush or dry cloth. • Regularly clean the motor housing using a damp cloth. Do not use any abrasive or solvent-based cleaner. Mains Plug Replacement If a new mains plug needs to be fitted: • Safely dispose of the old plug. • Connect the brown lead to the live terminal of the new plug. • Connect the blue lead to the neutral terminal. • If the product is class l (earthed), connect the green / yellow lead to the earth terminal. Warning! If your product is class ll double insulated (only 2 wires in the cord set), no connection is to be made to the earth terminal. Follow the fitting instructions supplied with good quality plugs. Any replacement fuse must be of the same rating as the original fuse supplied with the product. Technical Data ENGLISH Input voltage VAC KW1600E TYPE1 220-240 Power input W 1,600 No-load speed min-1 11,000 - 28,000 Collet size 1/2" (12.7)/ 1/4" (6.35)/ 8 mm / 6 mm Max. diameter of router bit mm 42 Max. depth of cut mm 60 Weight kg 5.1 15
Page 1 and 2: www.blackanddecker.ae KW1600
Page 3 and 4: 6 7 17 18 18 A B 11 23 13 C D 20 19
Page 5 and 6: 9 29 I J 34 30 31 9 29 K L 34 30 31
Page 7 and 8: Intended use Your Black & Decker ro
Page 9 and 10: • Hold the power tool by the insu
Page 11 and 12: Fitting a router bit (fig. A) • R
Page 13: • Turn the depth stop screw (35)
Page 17 and 18: 11 5 4 3 6 10 9 8 7 ARABIC 1 2 3 17
Page 19 and 20: E F 26 27 14 G H 16 21 28 ARABIC 15
Page 21 and 22: M N O P ARABIC 1 2 3 4 5 6 7 8 9 10
Page 23 and 24: QÉ«àdG Qó°üe øY »FÉHô¡µ
Page 25 and 26: Iõ¡LC’G ≈∏Y äÉ≤°ü∏
Page 27 and 28: á∏eÉc áØd .(34) §Ñ°†dG
Page 29 and 30: πãeC’G ΩGóîà°SÓd íFÉ°
Page 31 and 32: ¿Éª°†dG OGƒŸG ‘ Ö«Y Ö
Page 33 and 34: 6 7 17 18 18 A B 11 23 13 C D 20 19
Page 35 and 36: 9 29 I J 34 30 31 9 29 K L 34 30 31
Page 37 and 38: Utilisation prévue Votre fraiseuse
Page 39 and 40: • Tenez l'outil uniquement par le
Page 41 and 42: Mise en place d’une fraise (fig.
Page 43 and 44: • Tournez la vis de butée de pro
Page 45 and 46: Entretien Votre outil a été conç
Page 47 and 48: Garantie Lorsqu’un appareil Black
Page 49: YOUR NAME/ YOUR ADDRESS POSTCODE DA

Instruction Manual - Service - Black & Decker

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?