Anneaux DE (DIN 6799) A montage radial, externes, dim<strong>en</strong>sions métriques Les trois bossages de cet anneau sont <strong>en</strong> contact avec le fond de la gorge pour une rét<strong>en</strong>tion efficace de l'élém<strong>en</strong>t. Dim<strong>en</strong>sions de l'anneau Avec Section B-B Diamètre de l'Arbre Dim<strong>en</strong>sions de la Gorge Arrondi et Chanfrein maximum Diamètre de tolérance Monté dans la Gorge *Marge latérale (Y) Le rayon (arrondi) "R" du cote de la charge ne doit pas exceder 0,1T ANNEAU TAILLE ARBRE TAILLE DE GORGE TAILLE & POIDS DE L'ANNEAU TOLERANCE DONNEES COMPLEMENTAIRES REF. NOM. DIAMETRE LARGEUR EPAISSEUR ECARTEMENT POID DIAM. MONTE MARGE ANNEAU CHARGE R.ARRONDIS CHARGE LIMITES DIAMETRE *** LIBRE DS LATER- DE AXIALE & CHANFREINS MAX. DE (mm) LA ALE CHARGE (SUR Ds’ ADMISSIBLES AVEC VITESSE GORGE AXIALE ARBRE) ARR./ DE CHANF. ROTATION Ds MAX. Dg De A Dg Tol. W Tol. T Tol. A Tol. Kg/ G L2 Y Pr Pg Ds' R/Ch P'r 1000 Ref. Max. Min. kN kN Max. kN DE-0,8 0,8 1 1,4 0,8 -0,04 0,24 +0,04 0,2 0,58 0,003 1,95 2,25 0,4 0,08 0,03 1,2 0,3 0,04 50000 DE-1,2 1,2 1,4 2,0 1,2 0,34 -0,00 0,3 1,01 0,009 2,9 3,25 0,6 0,12 0,04 1,5 0,4 0,06 47000 DE-1,5 1,5 2,0 2,5 1,5 -0,06 0,44 0,4 1,28 ±0,04 0,021 3,9 4,25 0,8 0,22 0,07 2,0 0,6 0,11 42000 DE-1,9 1,9 2,5 3,0 1,9 0,54 0,5 1,61 0,040 4,40 4,8 1,0 0,35 0,10 2,5 0,7 0,17 40000 DE-2,3 2,3 3,0 4,0 2,3 0,64 0,6 1,94 0,069 5,90 6,3 1,0 0,50 0,15 3,0 0,9 0,24 38000 DE-3,2 3,2 4,0 5,0 3,2 0,64 0,6 ±0,02 2,70 0,088 6,90 7,3 1,0 0,65 0,22 4,0 0,9 0,32 35000 DE-4 4,0 5,0 7,0 4,0 -0,075 0,74 +0,05 0,7 3,34 0,158 8,85 9,3 1,2 0,95 0,25 5,0 1,0 0,47 32000 DE-5 5,0 6,0 8,0 5,0 0,74 -0,00 0,7 4,11 ±0,048 0,236 10,85 11,3 1,2 1,15 0,90 7,0 1,0 0,60 28000 DE-6 6,0 7,0 9,0 6,0 0,74 0,7 5,26 0,255 11,8 12,3 1,2 1,35 1,10 8,0 1,1 0,70 25000 DE-7 7,0 8,0 11,0 7,0 0,94 0,9 5,84 0,474 13,8 14,3 1,5 1,80 1,25 9,0 1,3 1,00 22000 DE-8 8,0 9,0 12,0 8,0 -0,09 1,05 1,0 6,52 0,660 15,75 16,3 1,8 2,50 1,42 10,0 1,5 1,25 20000 DE-9 9,0 10,0 14,0 9,0 1,15 1,1 7,63 ±0,058 1,090 18,20 18,8 2,0 3,00 1,60 11,0 1,6 1,50 17000 DE-10 10,0 11,0 15,0 10,0 1,25 1,2 8,32 1,250 19,70 20,4 2,0 3,50 1,70 12,0 1,8 1,75 15000 DE-12 12,0 13,0 18,0 12,0 -0,11 1,35 +0,08 1,3 ±0,03 10,45 1,630 22,7 23,4 2,5 4,70 3,10 15,0 1,9 2,30 13000 DE-15 15,0 16,0 24,0 15,0 1,55 -0,00 1,5 12,61 ±0,07 3,370 28,70 29,4 3,0 7,80 7,00 20,0 2,2 3,30 11000 DE-19 19,0 20,0 31,0 19,0 1,80 1,75 15,92 6,420 36,50 37,6 3,5 11 10,00 25,0 2,5 3,60 7600 DE-24 24,0 25,0 38,0 24,0 -0,13 2,05 2,00 21,88 ±0,084 8,550 43,50 44,6 4,0 15 13,00 30,0 3,0 4,00 5500 DE-30 30,0 32,0 42,0 30,0 2,55 2,50 25,80 13,50 51,3 52,6 4,5 23,00 16,50 36,0 3,5 5,30 4200 *BUTEE A ANGLE VIF. ***POUR DES ANNEAUX GALVANISES, AJOUTEZ 0,05 A L'EPAISSEUR MAXIMUM INDIQUEE. L'EPAISSEUR MAXIMUM DES ANNEAUX SERA INFERIEURE DE 0,005 AU MINIMUM PAR RAPPORT A LA LARGEUR DE GORGE MINIMUM (W) INDIQUEE. TOUTES LES DIMENSIONS SONT EN MILLIMETRES GAMMES DE DURETÉS : ANNEAUX EN ACIER INOXYDABLE (PH-15-7MO) TYPE D'ANNEAU TAILLES ÉCHELLE DURETÉ ROCKWELL 0,8-1,9 15N 82.5-86* DE 2,3-6 30N 63-69.5 7-30 C 44-51 *LA DURETE NE PEUT PAS ETRE MESUREE AVEC UNE QUELCONQUE PRECISION DIRECTEMENT SUR CES ANNEAUX. GAMMES DE DURETÉS : ANNEAUX EN CUPRO-BERYLLIUM TYPE D'ANNEAU TAILLES ÉCHELLE DURETÉ ROCKWELL 0,8-1,9 15N 79-82* DE 2,3-6 30N 56.5-62 7,30 C 37-43 *LA DURETE NE PEUT PAS ETRE MESUREE AVEC UNE QUELCONQUE PRECISION DIRECTEMENT SUR CES ANNEAUX. GAMMES DE DURETÉS : ANNEAUX EN ACIER INOXYDABLE (PH-15-7MO) TYPE D'ANNEAU TAILLES HV HRC DE 0,8-30 435-530 44-51 GAMMES DE DURETÉS : ANNEAUX EN CUPRO-BERYLLIUM TYPE D'ANNEAU TAILLES HV HRC DE 0,8-30 360-415 37-43 GAMMES DE DURETÉS : ANNEAUX EN ACIER AU CARBONE (SAE 1060-1090) TYPE D'ANNEAU TAILLES HV HRC DE 0,8-30 460-580 46-54 GAMMES DE DURETÉS : ANNEAUX EN ACIER AU CARBONE (SAE 1060-1090) TYPE D'ANNEAU TAILLES ÉCHELLE DURETÉ ROCKWELL 0,8-1,9 15N 83.5-87.5* DE 2,3-6 30N 65-72 7-30 C 46-54 *LA DURETE NE PEUT PAS ETRE MESUREE AVEC UNE QUELCONQUE PRECISION DIRECTEMENT SUR CES ANNEAUX. 40 Pour les dernières mises à jour de spécifications, les devis <strong>en</strong> ligne et les demandes d'échantillons, veuillez visiter le site rotorclip.com
A montage radial, externes, dim<strong>en</strong>sions métriques Idéal pour les applications à faible jeu où les installations radiales sont préférées. Anneaux DC Diamètre et dim<strong>en</strong>sions de l'anneau à l'état libre avec Section B-B Diamètre de l'Arbre Dim<strong>en</strong>sions de la Gorge Arrondi et Chanfrein admissibles Diamètre de tolérance Monté dans la Gorge Marge latérale (Y) *Le rayon (arrondi) "R" du cote de la charge ne doit pas exceder 0,1T ANNEAUARBRE TAILLE DE GORGE TAILLE & POIDS DE L'ANNEAU TOLERANCE DONNEES COMPLEMENTAIRES REF. DIAM DIAMETRE LARGEUR PROF. EPAISSEUR DIAMETRE SEC. POIDS DIAM. MONTE MARGE FORCE FORCE R.ARRONDIS CHARGE MAX. LIMITES (mm) *** ETAT LIBRE MAX. LIBRE DS LATER- DE DE & CHANFREINS AVEC ARR. MAX. DE LA ALE BUTEE BUTEE ADMISSIBLES OU CHANF. MAX. VITESSE GORGE ( lbs.) DE Ds Dg Tol. W d T Tol. Df Tol. S max Kg/ G L2 Y Pr Pg R/Ch P'r ROTATION Min. Ref. 1000 Ref. Max. Min. kN kN Max. kN DC-3 3 2,3 0,44 0,35 0,40 2,18 ±0,06 0,90 0,02 3,98 4,1 1,0 0,50 0,24 0,40 0,40 95000 DC-4 4 3,2 -0,07 0,44 0,40 0,40 3,00 1,00 0,04 5,00 5,2 1,2 0,50 0,37 0,40 0,40 90000 DC-5 5 4,0 0,64 0,50 0,60 -0,05 3,80 1,20 0,08 6,20 6,4 1,5 1,10 0,58 0,60 0,70 88000 DC-6 6 5,0 0,74 0,50 0,70 4,80 ±0,08 1,30 0,11 7,40 7,6 1,5 1,65 0,72 0,70 1,10 80000 DC-7 7 6,0 0,85 0,50 0,80 5,80 1,40 0,13 8,60 8,8 1,5 2,20 0,85 0,80 1,30 69000 DC-8 8 7,0 -0,09 0,85 0,50 0,80 6,80 1,60 0,17 10,00 10,2 1,5 2,20 0,98 0,80 1,30 67000 DC-9 9 8,0 1,10 0,50 1,00 7,80 ±0,09 1,70 0,22 11,20 11,4 1,5 3,50 1,10 1,00 2,00 58000 DC-10 10 9,0 1,10 0,50 1,00 8,75 1,70 0,26 12,15 12,4 1,5 3,70 1,24 1,00 2,00 50000 DC-11 11 10,0 1,10 0,50 1,00 9,65 1,80 0,29 13,20 13,6 1,5 4,00 1,35 1,00 2,00 40000 DC-12 12 10,9 1,10 0,55 1,00 10,55 1,90 0,32 14,35 14,7 1,7 4,20 1,65 1,00 2,00 35000 DC-13 13 11,8 1,10 0,60 1,00 11,40 2,00 0,36 15,40 15,8 1,8 4,50 1,90 1,00 2,00 30000 DC-14 14 12,7 1,10 0,65 1,00 12,30 2,00 0,40 16,30 16,7 2,0 5,00 2,20 1,00 2,00 27000 DC-15 15 13,6 -0,11 1,10 0,70 1,00 13,20 ±0,18 2,10 0,46 17,40 17,8 2,1 5,50 2,60 1,00 2,00 25000 DC-16 16 14,5 1,10 0,75 1,00 14,10 2,20 0,54 18,50 18,9 2,3 5,80 3,00 1,00 2,00 24000 DC-17 17 15,4 1,10 0,80 1,00 14,90 2,25 0,64 19,40 19,9 2,4 6,00 3,40 1,00 2,00 23000 DC-18 18 16,3 1,30 0,85 1,20 15,80 2,30 0,72 20,40 20,9 2,6 8,50 3,70 1,20 2,80 21000 DC-19 19 17,2 1,30 0,90 1,20 16,70 2,40 0,80 21,50 22,0 2,7 9,00 4,30 1,20 2,80 21000 DC-20 20 18,1 1,30 0,95 1,20 -0,06 17,55 2,55 0,87 22,65 23,2 2,9 9,40 4,70 1,20 3,00 20000 DC-22 22 19,9 1,30 1,05 1,20 19,40 2,80 1,10 25,00 25,5 3,2 10,00 5,70 1,20 3,00 17000 DC-23 23 20,8 1,30 1,10 1,20 20,20 2,90 1,15 26,00 26,6 3,3 10,50 6,20 1,20 3,20 15000 DC-24 24 21,7 1,30 1,15 1,20 21,10 3,00 1,52 27,10 27,7 3,5 11,00 6,80 1,20 3,20 15000 DC-25 25 22,6 -0,21 1,30 1,20 1,20 22,00 ±0,21 3,15 1,74 28,30 28,9 3,6 11,50 7,50 1,20 3,20 15000 DC-26 26 23,5 1,30 1,25 1,20 22,90 3,25 1,88 29,40 30,0 3,8 12,00 8,00 1,20 3,20 15000 DC-28 28 25,2 1,60 1,40 1,50 24,60 3,50 2,32 31,60 32,2 4,2 16,50 9,70 1,50 5,50 13000 DC-30 30 27,0 1,60 1,50 1,50 26,30 3,70 2,43 33,70 34,4 4,5 17,00 11,00 1,50 5,60 13000 DC-32 32 28,8 1,60 1,60 1,50 28,10 4,00 3,02 36,10 36,8 4,6 18,00 12,50 1,50 5,80 13000 DC-35 35 31,5 1,60 1,75 1,50 30,80 4,30 3,30 39,40 40,1 5,3 20,00 15,00 1,50 5,80 11000 DC-36 36 32,4 1,85 1,80 1,75 31,70 ±0,25 4,40 4,40 40,50 41,2 5,4 25,00 16,00 1,75 8,30 10000 DC-38 38 34,2 1,85 1,90 1,75 33,40 4,60 4,62 42,60 43,4 5,7 26,00 17,50 1,75 8,50 10000 DC-40 40 36,0 1,85 2,00 1,75 35,20 4,90 5,05 45,00 45,8 6,0 27,50 20,00 1,75 8,80 9000 DC-42 42 37,8 -0,25 1,85 2,10 1,75 37,00 5,10 5,46 47,20 48,0 6,3 28,00 21,50 1,75 8,90 9000 DC-45 45 40,5 1,85 2,25 1,75 39,60 5,50 5,98 50,60 51,5 6,8 30,00 25,00 1,75 9,00 8000 DC-48 48 43,2 1,85 2,40 1,75 42,30 ±0,39 5,90 7,82 54,10 55,0 7,2 32,00 28,00 1,75 9,00 8000 DC-50 50 45,0 2,15 2,50 2,00 44,00 6,20 8,85 56,40 57,4 7,5 39,50 31,00 2,00 12,00 7000 DC-52 52 47,0 2,15 2,50 2,00 -0,07 46,00 6,30 9,33 58,60 59,6 7,5 41,00 32,00 2,00 12,00 7000 DC-55 55 50,0 2,15 2,50 2,00 48,50 6,50 10,40 61,50 63,0 7,5 43,00 34,00 2,00 12,00 7000 ***POUR DES ANNEAUX GALVANISES, AJOUTEZ 0,05 A L'EPAISSEUR MAXIMUM INDIQUEE. L'EPAISSEUR MAXIMUM DES ANNEAUX SERA INFERIEURE DE 0,005 AU MINIMUM PAR RAPPORT A LA LARGEUR DE GORGE MINIMUM (W) INDIQUEE. TOUTES LES DIMENSIONS SONT EN MILLIMETRES GAMMES DE DURETÉS : ANNEAUX EN ACIER INOXYDABLE (PH-15-7MO) TYPE D'ANNEAU TAILLES ÉCHELLE DURETÉ ROCKWELL 3-4 15N 82.5-86 DC 5-19 30N 63-69.5 20-55 C 44-51 GAMMES DE DURETÉS : ANNEAUX EN ACIER INOXYDABLE (PH-15-7MO) TYPE D'ANNEAU TAILLES HV HRC DC 3-55 435-530 44-51 GAMMES DE DURETÉS : ANNEAUX EN ACIER INOXYDABLE (PH-15-7MO) TYPE D'ANNEAU TAILLES ÉCHELLE DURETÉ ROCKWELL 3-4 15N 82.5-86 DC 5-19 30N 63-69.5 20-55 C 44-51 GAMMES DE DURETÉS : ANNEAUX EN ACIER AU CARBONE (SAE 1060-1090) TYPE D'ANNEAU TAILLES HV HRC DC 3-55 485-545 48-52 Pour les dernières mises à jour de spécifications, les devis <strong>en</strong> ligne et les demandes d'échantillons, veuillez visiter le site rotorclip.com 41
- Page 1 and 2: TABLE DES MATIÈRES Index des Produ
- Page 3 and 4: INDEX DES PRODUITS (CONT.) CIRCLIPS
- Page 5 and 6: CODES D'ARTICLES ET CONDITIONNEMENT
- Page 7 and 8: otorclip.com/rotorclamp.com DEMANDE
- Page 9 and 10: PRODUITS, FAITS, INFORMATION ÉLECT
- Page 11 and 12: PROCESSUS ET INGÉNIERIE SUPÉRIEUR
- Page 13 and 14: MATRICES POUR FILS / MATRIÇAGE SP
- Page 15 and 16: PROCÉDURES D'INSPECTIONS LIMITATIO
- Page 17 and 18: TREMPE BAINITIQUE DURETÉ ET MÉTHO
- Page 19 and 20: TESTS LES PROCÉDURES DE TESTS ET L
- Page 21 and 22: APPLICATIONS Un anneau interne Ho r
- Page 23 and 24: SECTION CONSTANTE ET SECTION ÉVOLU
- Page 25 and 26: Circlips à Section Évolutive, Dim
- Page 27 and 28: À montage axial, internes, dimensi
- Page 29 and 30: À montage axial, internes, dimensi
- Page 31 and 32: A montage axial, internes, dimensio
- Page 33 and 34: A montage axial, externes, dimensio
- Page 35 and 36: À montage axial, externes, dimensi
- Page 37 and 38: À montage axial, externes, dimensi
- Page 39: À montage axial, externes, dimensi
- Page 43 and 44: Autobloquants, internes, dimensions
- Page 45 and 46: Circlips à Section Évolutive, à
- Page 47 and 48: À montage axial, internes Une fois
- Page 49 and 50: À montage axial, internes Une fois
- Page 51 and 52: À montage axial, internes Une fois
- Page 53 and 54: A montage axial, externes Une fois
- Page 55 and 56: A montage axial, externes Une fois
- Page 57 and 58: A montage axial, externes Une fois
- Page 59 and 60: A montage axial, internes La positi
- Page 61 and 62: A montage axial, externes La positi
- Page 63 and 64: A montage axial, externes Cet annea
- Page 65 and 66: A montage axial, externes Cet annea
- Page 67 and 68: A montage axial, internes, cintrés
- Page 69 and 70: A montage axial, externes, cintrés
- Page 71 and 72: A montage axial, internes Un bord b
- Page 73 and 74: A montage axial, internes Un bord b
- Page 75 and 76: A montage axial, externes Un bord b
- Page 77 and 78: A montage axial, externes Un bord b
- Page 79 and 80: Circlips à section évolutive, à
- Page 81 and 82: A montage axial, externes Les trois
- Page 83 and 84: A montage axial, externes Une versi
- Page 85 and 86: A montage axial, externes Idéal po
- Page 87 and 88: A montage radial, externes Les deux
- Page 89 and 90: A montage radial, externes L'anneau
- Page 91 and 92:
Externes, pour absorption de jeu Un
- Page 93 and 94:
Externes, pour absorption de jeu De
- Page 95 and 96:
Circlips autobloquants, à section
- Page 97 and 98:
Externes, autobloquants L'anneau ex
- Page 99 and 100:
Externes, autobloquants Les griffes
- Page 101 and 102:
À montage radial, externes, dimens
- Page 103 and 104:
Circlips à Section évolutive, dim
- Page 105 and 106:
À montage axial, internes, dimensi
- Page 107 and 108:
À montage axial, internes, dimensi
- Page 109 and 110:
A montage axial, externes, dimensio
- Page 111 and 112:
A montage axial, externes, dimensio
- Page 113 and 114:
A montage axial, externes, dimensio
- Page 115 and 116:
A montage radial, externes, dimensi
- Page 117 and 118:
A montage radial, externes, dimensi
- Page 119 and 120:
A montage radial, externes, dimensi
- Page 121 and 122:
Modèles Optionnels de Coupures, à
- Page 123 and 124:
Procédures d'Inspection des anneau
- Page 125 and 126:
Interne, pour roulements à aiguill
- Page 127 and 128:
Interne, à encoches UHO à Section
- Page 129 and 130:
Interne UHB à Section Constante Ma
- Page 131 and 132:
Externe, pour roulements à aiguill
- Page 133 and 134:
Externe, pour roulements à aiguill
- Page 135 and 136:
Externe, à section ronde RHC/RLC -
- Page 137 and 138:
Interne, pour roulements standards
- Page 139 and 140:
Externe, pour roulements standards
- Page 141 and 142:
Externe, fils plat, dimensions mét
- Page 143 and 144:
Interne, fils plat, dimensions mét
- Page 145 and 146:
Externe, pour roulements, dimension
- Page 147 and 148:
Interne, fils rond, dimensions mét
- Page 149 and 150:
Outils pour Colliers de Serrage MON
- Page 151 and 152:
HW Colliers de Serrage - Brides min
- Page 153 and 154:
CTB Colliers de Serrage Pour Boyaux
- Page 155 and 156:
Formules CALCUL DE LA MARGE LATÉRA
- Page 157 and 158:
Assemblage Automatisé pour anneaux
- Page 159 and 160:
Pinces Les spécifications concerna
- Page 161 and 162:
Pinces à Cliquet DESSINS TECHNIQUE
- Page 163 and 164:
Fourchettes de Pose Pour circlips C
- Page 165 and 166:
Distributeurs Pour les distributeur
- Page 167 and 168:
Kits de Pinces pour Circlips Kits d