SMSB-M21T-AB - Elbro AG

More documents

Recommendations

Info

SMSB-M21T-ABManual Switch ButtonThe operation of this button depends on the functions activated.Function Operation Relay status LEDNoneThe relay changes status from OFF to ON and vice versaRED: OFFGREEN: ONAUTO: ONThe device deactivates the automatic function and the RED: OFFrelay outputFROST: ONThe device switches from antifreeze to automatic andvice versaFlashing red light: ANTIFREEZEFlashing green light: AUTOMATICRMODE: PULSE The device emits the pulse RED: OFFGREEN: ONCommand SMSThe device has a series of setup and control commands that may be sent by SMS. The command message is protectedby a password (see the system password section).The command message has the following format:[PASSWORD]#[COMMAND] for example: 0000#1 (turn relay on)Where:the password always has 4 characters; #: hash is an obligatory separator (only the dot character may be used as an alternative).The table below contains a list of the standard commands available together with their description, for example:Command Description Example Response0 Turns off the relay output (disables AUTO) 0000#0 OFF1 Turn on the relay output (disables AUTO) 0000#1 ON? Finds out the current status 0000#? Current statusATurns on the AUTO function.0000#A Th: 20CAdopts the previous threshold value; 20°C by defaultA[1-50] Enables the AUTO function and sets the threshold. 0000#A25 Th: 25CFEnables the FROST function.0000#F Tf: 8CAdopts the previous threshold value; 8°C* by defaultThe table below lists the advanced commands available (without having to use the software) together with their description,for example:Command Description Example ResponseF0 Disables FROST function 0000#F0F[1-49] Enables the FROST function and sets the threshold. 0000#F6 Tf: 6CI Shows the status of the contact of the input 0000#IN[0-1] 0: disables antifreeze notification0000#N0NOTIFY: OFF1: enables antifreeze notification0000#N1NOTIFY: ONP Changes the system password 0000#P1234 new password 1234S[1-2]? Shows the text of the current message 0000#S1?S1: Modifies the text of input no.1 contact opening 0000#S1:input 1 openedS2: Modifies the text of input no. 1 contact closure 0000#S2:input 1 closedT[0-1] 0: disables the temperature1: enables internal sensor only0000#T00000#T1T+Calibrates the sensor: only with TMODE=10000#T+1T-0000#T-3U? Shows the list of previous administrator users 0000#U?U[1-6]- Removes a user from the list 0000#U2-U[1-6]:[num] Adds or modifies the specified user 0000#U1:+3912345678* Warning: Do not use this device as a safety device frostTMODE: OFFTMODE: INTUpdated status16
SMSB-M21T-ABQuick CommandsThe device has a series of quick commands without any need for a password, which may be sent exclusively byadministrator users. These commands are listed in the table below:Command Description Example ResponseOFF Turns the relay output off (disables AUTO) OFF OFFON Turns the relay output on (disables AUTO) ON ONSTATUS Finds out the current status STATUS Current statusAUTO Activates the AUTO function at the threshold programmed previouslyAUTO Th: 20CNote: the commands sent must consist exclusively of capital letters and with no spaces.TroubleshootingIf a fault arises, the error signalling LED will flash red. Count the number of flashes to identify the error code as indicatedin the table below:Flashing codeDescription1 System error: try restarting the device2 The SIM card is protected by a PIN code3 The SIM card is not presentLED OFFSystem error: try restarting the device. If the problem persists, call the technical serviceNameplate DataGSM Section Dual-band mode 900Mhz ,1800MHzPower suppy Supply voltage: 12V DC (9-24V) Current: Imax = 1000mA The device must be powered by a power source limited to 24VA. Power supply protected against reversed polarityOutput 1 Relay SPDTo 0,5A, 250V AC (Resistive);o 1A, 30V DC.Input 1 digital input (VCC)Main characteristics Degree of infiammability: UL94V-0 Protection degree: IP20 Standard operating temperature: -5°C to +45°C Max conductor size: 2,5mm 2 USB programming portCertificationsCurrent drawn(typical values)Health and Safety: EN 62311 (2008)Electromagnetic Compatibility: EN 301489-1 V1.8.1 (2008)Effective use of radio spectrum: EN 301511 V9.02 (2003)Standby 40mASending\Receiving SMS 200mA EN 60950-1 (2006) + A11 (2009) EN 301489-7 V1.3.1 (2005)Software RequirementsThe following table lists the operating systems supported by the software SMSB-M21T-AB.Operating systemNOTEWindows XP SP3Windows Vista SP2Windows 7The .NET Framework Client Profile is not supported on IA-64-based (Itanium) systems.For all platforms, we recommend that you upgrade to the latest Windows Service Pack and critical updates availablefrom the Windows Update Web site to ensure the best compatibility and security.17
Page 1 and 2: SMSB-M21T-AB Bedienungsanleitung Ma
Page 3 and 4: 186,0 mm77,5 mm106,1 mm5,0 mm5,0 mm
Page 5 and 6: SMSB-M21T-ABEinbauplan5
Page 7 and 8: SMSB-M21T-ABDie Programmiersoftware
Page 9 and 10: SMSB-M21T-AB#: das Rautenzeichen is
Page 11 and 12: SMSB-M21T-ABSafety Information Do n
Page 13 and 14: SMSB-M21T-ABInserting the SIM cardB
Page 15: SMSB-M21T-ABAlarm InputThe device h
Page 19 and 20: SMSB-M21T-ABSchéma d'installation1
Page 21 and 22: SMSB-M21T-ABProgrammation par l’i
Page 23 and 24: SMSB-M21T-ABBouton de commutation m
Page 25 and 26: SMSB-M21T-ABInformazioni per la sic
Page 27 and 28: SMSB-M21T-ABInserimento della sim c
Page 29 and 30: SMSB-M21T-ABIngresso di allarmeIl d
Page 31: SMSB-M21T-ABComandi rapidiIl dispos

SMSB-M21T-AB - Elbro AG

Create successful ePaper yourself

Delete template?

Save as template?