Dat air ITA GB 05 2003 - Frigomaster - Idee in grado di cambiare il ...
Dat air ITA GB 05 2003 - Frigomaster - Idee in grado di cambiare il ...
Dat air ITA GB 05 2003 - Frigomaster - Idee in grado di cambiare il ...
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Il vent<strong>il</strong>atore dell’unità è attivo, la valvola a<br />
tre vie si trova <strong>in</strong> posizione <strong>di</strong> chiusura<br />
mentre <strong>il</strong> compressore è attivo per v<strong>in</strong>cere<br />
<strong>il</strong> carico termico ambiente.<br />
4. Refrigeratore d’acqua spento (ovvero non<br />
c’è presenza <strong>di</strong> acqua refrigerata o la<br />
temperatura dell’acqua è superiore ad un<br />
certo valore impostato) e set <strong>di</strong> temperatura<br />
sod<strong>di</strong>sfatto. In questo caso entrambe le<br />
sorgenti <strong>di</strong> freddo sono <strong>di</strong>sattivate e solo i<br />
vent<strong>il</strong>atori risultano <strong>in</strong> funzione.<br />
Nel caso <strong>di</strong> unità HH, l’azione <strong>di</strong><br />
deumi<strong>di</strong>fica viene svolta solo dalla<br />
sorgente fredda attiva <strong>in</strong> quel momento.<br />
Rispetto all’unità tipo *ED* con allestimento<br />
base sono presenti i seguenti componenti<br />
aggiuntivi:<br />
• batteria ad acqua refrigerata<br />
• valvola a tre vie <strong>di</strong> tipo modulante tramite<br />
segnale elettrico 0 ÷ 10 Vdc<br />
• un flussostato a paletta ed una sonda <strong>di</strong><br />
temperatura tipo NTC<br />
In queste unità, per qualunque tipologia CO<br />
CH o HH, viene sempre <strong>in</strong>stallato <strong>il</strong> controllo<br />
a microprocessore DATALOGIC 2 .<br />
Unità RP<br />
Le unità con allestimento RP sono <strong>di</strong> tipo<br />
OVER (mandata verso l’alto) con ripresa<br />
posteriore anziché frontale. Sono<br />
particolarmente <strong>in</strong><strong>di</strong>cate per essere ut<strong>il</strong>izzate<br />
quando l’aria <strong>di</strong> ripresa proviene da canali.<br />
In this mode, the unit fan is active, the 3way<br />
valve <strong>in</strong>hibits ch<strong>il</strong>led water flow<br />
through the co<strong>il</strong> wh<strong>il</strong>e the compressor is<br />
activated to meet the ambient thermal load.<br />
4. water ch<strong>il</strong>ler off (i.e. no ch<strong>il</strong>led water<br />
present or water temperature is greater<br />
than sett<strong>in</strong>g) and temperature sett<strong>in</strong>g<br />
reached.<br />
In this mode, both cool<strong>in</strong>g sources are<br />
deactivated, fans only are operat<strong>in</strong>g.<br />
For “HH” version units, dehumi<strong>di</strong>fication is<br />
only carried out by the cool<strong>in</strong>g source<br />
activated at the time.<br />
With respect to *ED* type units <strong>in</strong> the basic<br />
configuration, the follow<strong>in</strong>g equipment is present:<br />
• ch<strong>il</strong>led water co<strong>il</strong><br />
• three-way valve modulated by an 0 - 10<br />
Vdc signal<br />
• vane flowswitch and NTC temperature<br />
probe<br />
In these units, irrespective of type (CO, CH<br />
or HH), the DATALOGIC 2 microprocessor<br />
controller is always <strong>in</strong>stalled.<br />
RP Units<br />
Units with RP configuration are of the OVER<br />
type (with upward <strong>air</strong> delivery) with rear <strong>air</strong><br />
<strong>in</strong>take rather than front <strong>air</strong> <strong>in</strong>take.<br />
These units are particularly suitable for use <strong>in</strong><br />
<strong>in</strong>stallations where the <strong>in</strong>take <strong>air</strong> is ducted.<br />
AIR BLUE .17