HWA 1001 INOX HWA 1300 F - AL-KO Garten + Hobby
HWA 1001 INOX HWA 1300 F - AL-KO Garten + Hobby
HWA 1001 INOX HWA 1300 F - AL-KO Garten + Hobby
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
During the first operation the pump automatically<br />
switches off after approx. 10 sec.<br />
Afterwards the button "RESET“(28) must<br />
be pressed so long until the pump delivers<br />
water. If the button "RESET" is released<br />
before the pump delivers water, the pump<br />
switches off automatically due to safety<br />
reasons. Should the suction process last<br />
longer than 2 min. refill the pump and<br />
suction hose once again, check screw<br />
connections for tightness and repeat the<br />
process.<br />
• As soon as the flow of water is cleared of air<br />
bubbles trapped in the line, close the pressure<br />
line. When the pressure has fallen and<br />
the reservoir is full, the pump will automatically<br />
in approx. 15 sec. switch off. Your domestic<br />
water system is now ready for operation.<br />
Switching off the system<br />
• Switch the system off by unplugging the<br />
electric cable from the socket.<br />
Operating the system<br />
Put the system into operation as described<br />
above (Setting up and operating the system).<br />
The domestic water system is electronically<br />
controlled and works automatically after the initial<br />
operation.<br />
Manual restart<br />
• After malfunction or when no water is delivered<br />
during the initial operation, the pump<br />
must be started manually.<br />
• Check the suction side of the system and<br />
water level.<br />
• Start the pump by pressing the button<br />
"RESET“ (28).<br />
• When water is not delivered after several<br />
unsuccessful trials, check the screw connections<br />
for tightness and refill the pump.<br />
• With regard to WHA <strong>1300</strong> F check for the<br />
correct seat of the transparent cover (9) of<br />
the filter.<br />
Operating state indicators<br />
The states of operation are with the help of<br />
warning lights (LED).<br />
Warning light "Power" (25)<br />
Shows whether or not the system is connected to<br />
the mains<br />
Warning light "Failure" (26)<br />
Shows that a fault has occurred<br />
Warning light "On" (27)<br />
Shows that the pump is in operation<br />
Maintenance and Cleaning<br />
Before beginning any maintenance or<br />
cleaning work, make sure that the device<br />
has been unplugged and take precautions<br />
to ensure that it cannot be switched on<br />
during work!<br />
Cleaning the system<br />
If you have used your domestic water system to<br />
pump chlorine water (swimming pool water) or<br />
liquids which leave a residue, flush your pump<br />
out with clear water after use.<br />
Cleaning the filter (only <strong>HWA</strong> <strong>1300</strong> F)<br />
• Remove the screw plug (7) from the drainage<br />
opening, empty the filter chamber and<br />
close the drainage opening again<br />
• Unscrew the filter cover (9) with the help of<br />
the filter spanner.<br />
• Remove the filter (20) from the pump head<br />
and clean it under flowing water.<br />
• Prior to installing the filter, check the two<br />
seals (19) on the filter and the seal (23) for<br />
damage, if necessary renew.<br />
The seal (23) must be correctly inserted in<br />
the seal seat on the pump head (see Detail<br />
in Fig. D). If necessary lightly grease the<br />
seal with non-acidic fat.<br />
• Install the filter, screw on filter cover and<br />
tighten firmly with the hand using filter spanner.<br />
Clearing blockages (<strong>HWA</strong> <strong>1001</strong> <strong>INOX</strong>)<br />
Eliminate blocking inside the pump as follows:<br />
• Remove the suction hose on the pump inlet<br />
(8).<br />
• Attach the pressure hose to the water tap<br />
and spray water into the pump chamber until<br />
the blockage is flushed out.<br />
• Check to see that the obstruction has been<br />
cleared entirely by switching on the pump for<br />
a short time.<br />
Translation of original user instructions GB 4