LINE TRIMMER 0735 (F0150735..)

- clean ventilation slots J 2 regularly with a brush orcompressed air• Regularly check the condition of the cutting head and thetightness of nuts, bolts and screws• Regularly check for worn or damaged components andhave them repaired/replaced when necessary• Storage &- store the tool indoors in a dry and locked-up place,out of reach of children- securely mount storage rail K on the wall with 4 screws(not supplied) and horizontally leveled• If the tool should fail despite the care taken in manufacturingand testing procedures, repair should be carried out by anafter-sales service centre for SKIL power tools- send the tool undismantled together with proof ofpurchase to your dealer or the nearest SKIL servicestation (addresses as well as the service diagram ofthe tool are listed on www.skil.com)TROUBLESHOOTING• The following listing shows problem symptoms, possiblecauses and corrective actions (if these do not identify andcorrect the problem, contact your dealer or service station)! switch off the tool and disconnect the plug beforeinvestigating the problem★ Tool does not operate- power supply socket faulty -> use another socket- extension cord damaged -> replace extension cord★ Tool operates intermittently- internal wiring defective -> contact dealer/service station- on/off switch defective -> contact dealer/service station★ Tool vibrates abnormally- grass too high -> cut in stages★ Tool does not cut- line too short/broken off -> feed the line manually★ Line cannot be fed- spool empty -> replace spool- line entangled inside spool -> inspect spool; rewind ifnecessary★ Line is not cut off to correct length -> remove cover fromcutting blade★ Line keeps breaking- line entangled inside spool -> inspect spool; rewind ifnecessary- trimmer incorrectly used -> only trim with the tip of theline; avoid stones, walles and other hard objects; feedthe line regularlyENVIRONMENT• Do not dispose of electric tools, accessories andpackaging together with household waste material(only for EU countries)- in observance of European Directive 2002/96/EC onwaste of electric and electronic equipment and itsimplementation in accordance with national law,electric tools that have reached the end of their lifemust be collected separately and returned to anenvironmentally compatible recycling facility- symbol 9 will remind you of this when the need fordisposing occursDECLARATION OF CONFORMITY• We declare under our sole responsibility that this productis in conformity with the following standards orstandardized documents: EN 60335, EN 61000,EN 55014 in accordance with the provisions of thedirectives 2006/95/EC, 2004/108/EC, 2006/42/EC,2000/14/EC, 2011/65/EU• Technical file at: SKIL Europe BV (PT-SEU/PJE),4825 BD Breda, NL25.07.2012 11NOISE/VIBRATION• Measured in accordance with EN 60335 the soundpressure level of this tool is 70 dB(A) and the sound powerlevel 90 dB(A) (standard deviation: 3 dB), and the vibration< 2.5 m/s² (hand-arm method; uncertainty K = 1.5 m/s²)• Measured in accordance with 2000/14/EC (EN/ISO3744) the guaranteed sound power level LWA is lowerthan 93 dB(A) (conformity assessment procedureaccording to Annex VI)Notified body: KEMA, Arnhem, NLNotified body identification number: 0344• The vibration emission level has been measured inaccordance with a standardised test given in EN 60335; itmay be used to compare one tool with another and as apreliminary assessment of exposure to vibration whenusing the tool for the applications mentioned- using the tool for different applications, or with differentor poorly maintainted accessories, may significantlyincrease the exposure level- the times when the tool is switched off or when it isrunning but not actually doing the job, may significantlyreduce the exposure level! protect yourself against the effects of vibration bymaintaining the tool and its accessories, keepingyour hands warm, and organizing your work patternsCoupe-bordures 0735INTRODUCTION• Cet outil est destiné à couper les herbes et mauvaisesherbes sous les buissons ainsi que sur les pentes et lesbordures qui ne peuvent être atteintes avec une tondeuse• Cet outil n’est conçu pour un usage professionnel• Vérifiez que le conditionnement contient toutes lespièces présentées dans le schéma 2• Lorsque des pièces manquent ou sont endommagées,veuillez contacter votre distributeur8