Views
1 week ago

KitchenAid 901 506 22 - 901 506 22 EN (857921516020) Istruzioni per l'Uso

KitchenAid 901 506 22 - 901 506 22 EN (857921516020) Istruzioni per l'Uso

61002001.book Page 20

61002001.book Page 20 Tuesday, March 25, 2008 4:46 PM Changing the rear oven lamp (if provided): 1. Disconnect the oven from the power supply. 2. Allow the oven cool before turning the lamp cover left to unscrew it (see fig. 1). 3. Replace the lamp (see note). 4. Screw the lamp cover back on. 5. Reconnect the oven to the power supply. Note: Only use 25 W/230 V, E-14 type T300°C lamps available from the After-Sales Service. Important: Do not use the oven before refitting the lamp cover. 1 Replacing the side lamp (if provided): 1. Disconnect the oven from the power supply. 2. Remove the left side accessory holder grille after allowing the oven cool (see fig. 2). Using a screwdriver, prise outwards to remove the lamp cover (see fig. 3 - 4). 3. Replace the lamp (see note). 4. Refit the lamp cover, pressing it against the oven wall to correctly hook it. 5. Refit the side accessory holder grille. 6. Reconnect the oven to the power supply. Note: Only use 25 W/230 V, E-14 type T300°C lamps available from After-Sales Service. Important: Do not use the oven before refitting the lamp cover. 2 Replacing the side halogen lamp (if provided): 1. Disconnect the oven from the power supply. 2. Remove the left side accessory holder grille after allowing the oven cool (see fig. 2). Using a screwdriver, prise outwards to remove the lamp cover (see fig. 3 - 4). 3. Do not replace the lamp with bare hands. Carefully remove the halogen lamp from the lamp holder and replace it with a new one (see note). 4. Refit the lamp cover, press it against the oven wall to correctly hook it. 5. Refit the side accessory holder grille. 6. Reconnect the oven to the power supply. Note: Only use 20 W/12 V, G4 type T300°C lamps available from our After-Sales Service. Important: Do not use the oven before refitting the lamp cover. 3 4 20

61002001.book Page 21 Tuesday, March 25, 2008 4:46 PM TROUBLESHOOTING GUIDE The oven does not work: • Check the mains power and that the oven is electrically connected. • Turn the oven off and then on again to see if the fault has been eliminated. IMPORTANT: • Make sure the oven selector is not set to “0” or on the “lamp” symbol . - If the electronic programmer (if provided) indicates “ ”, consult the separate product sheet and/or the electronic programmer description. - If the electronic programmer (if provided) indicates “F XX”, contact the nearest After- Sales Service. In this case specify the number after the letter “F”. - Make sure the mechanical programmer (if provided) is set to “manual”. AFTER-SALES SERVICE Before calling the After-Sales Service: 1. Try to eliminate the problem on your own, according to the points described in “Troubleshooting Guide”. 2. Switch the appliance off and then on again to see if the problem has been eliminated. If the fault persists after the above checks, contact the nearest After-Sales Service. Always specify: •a brief description of the fault; •the exact oven model and type; •the After-Sales Service number (number after the word Service on the dataplate), located on the right inside edge of the oven compartment (visible when the door is open). The After- Sales Service number is also given in the warranty booklet; •your full address; •your telephone number. If any repairs are required, contact an authorised Technical Service Centre (to guarantee the use of original spare parts and correct repair). Failure to comply with these instructions can compromise the safety and quality of the product. DECLARATION OF CONFORMITY • This oven is intended to come into contact with food products and complies with European Regulation no. 1935/2004. • It is designed to be used only as a cooking appliance. Any other use (e.g. for room heating) is considered improper and therefore potentially dangerous. • This appliance has been designed, manufactured and put on the market in compliance with: - the safety requirements of “Low Voltage” Directive 2006/95/EC (replacing 73/23 EEC amended) - the protection requirements of EMC Directive 89/336/EEC - the requirements of Directive 93/68/EEC. 21