Handleiding Floormaster - Parket- en Laminaatsnijder

More documents

Recommendations

Info

7051642_Floormaster:7051642 31.08.2009 8:20 Uhr Seite 8 GB FULL LENGTH, CROSS-CUT AND DIAGONAL CUTS 1. Place the Floormaster cutter on the floor making sure it is on a level surface. 1. 1a. 2. Mark your cut line across the entire length of the laminate piece, with the finished side (decorative side) facing up (fig. 1). Note: When using laminate with attached padding, cut with the finished side down and pad side up. This will insure the plank can move easily through the blades without having the padding stuck to the base of the laminate cutter. 2. 2a. 3. The Floormaster has a dual blade system. Position your marked cut line on one of the guidelines of the base to align the cut with the blades (fig. 1a). Both guide lines on the base provide a reference for the offcut material and can also serve as guides to keep your cut straight. Make sure to position the side to be used outside the guidelines, with the “scrap portion” between the blades. 4. Before cutting, make sure the ratchet directional switch (|F) on the handle is in the down (forward) position (fig. 2). Remember that the scrap will be fed through the middle of the dual blades and gets lost when cutting. For cutting hold the laminate firmly with one hand and pull the handle down with the other hand. Continue cranking the handle until the cut is complete. There is no need to push the plank; the patented dual blade system automatically will feed the plank while cutting. Note: If the plank begins to move off the cutting line, stop. Reverse (fig. 2a) the directional switch (|F) and push the handle to back out the plank. Once you have re-aligned the plank flip the directional switch to resume cutting in a forward direction. The cut side of the plank should be placed along the wall. The cut side of the plank (unfinished) will then be covered by baseboard or finish moulding. NOTCH CUTS 1. Mark the notch you want to cut out. Notches are used around door ways or other obstructions in the layout of the floor. 2. Cut along the mark and once the desired notch length has been reached, flip the directional lever (|F) and completely back out the laminate plank (fig. 3). 3. Repeat the process for the other side of the notch (fig. 3a). 3. 3a. 8 |
7051642_Floormaster:7051642 31.08.2009 8:20 Uhr Seite 9 GB MAINTENANCE AND CARE • Keep the Floormaster clean by using a dry clean cloth. • Store the unit in a dry place when not in use. • Periodically check all assembled parts and ensure firm setting. • Remove dust and debris from the opening between the saw blades and the base. Technical Data Laminate Cutter Size Handle Max. Cutting Height Saw Blade 1 706 x 123 x 124 mm 545 mm 12 mm 80 x 1.2 mm 1 Replacement saw blades can be ordered at Batavia (Article No. 7053705). Disposal Dear Customer, please help avoid waste materials. If you at some point intend to dispose of this article, then please keep in mind that many of its components consist of valuable materials, which can be recycled. Please do not dis charge it in the rubbish bin, but check with your local council for recycling facilities in your area. | 9
Page 1 and 2: TM 7051642_Floormaster:7051642 31.0
Page 3 and 4: 7051642_Floormaster:7051642 31.08.2
Page 5 and 6: 7051642_Floormaster:7051642 31.08.2
Page 7: 7051642_Floormaster:7051642 31.08.2

Handleiding Floormaster - Parket- en Laminaatsnijder

Create successful ePaper yourself

Delete template?

Save as template?