MOBITRONIC M45R - Waeco

More documents

Recommendations

Info

_M45.book Seite 34 Freitag, 21. November 2008 11:05 11 Mounting the monitor <strong>M45R</strong> 7.5 Connecting the monitor to an electricity supply (fig. e, page 10) The circuit diagram for the monitor can be found in fig. e, page 10. No. Description 1 Rear view of the monitor 2 Light switch 3 Switch for the rear headlamp 4 Ignition socket 5 Branch connector or soldering point 6 Instrument illumination 7 Reverse headlamp 8 Camera br brown rt red sw black ws white Observe the following instructions when laying the connection cable: I Note Feed the connection cable through existing ducts or other openings where possible e. g. ventilation grilles. If no appropriate ducts or openings are available you will need to drill a hole of ∅ 18 mm. Check beforehand that there is sufficient space on the other side for the drill head to come out (fig. 2, page 4). I Note Please observe the notes from the chapter “General information on the electrical connections” on page 29. ➤ Plug the connection cable into the power socket (fig. b 4, page 7) on the back of the monitor. e Caution! Make sure the polarity is correct when connecting to a voltage source. ➤ Connect the red and black cables of the connection cables to a suitable voltage source: – Connect the red cable to terminal 15 (ignition). – Connect the black cable to terminal 31 (earth). ➤ Connect the brown cable to the positive cable of the reversing light (7). 34
_M45.book Seite 35 Freitag, 21. November 2008 11:05 11 <strong>M45R</strong> Using the monitor I Note If voltage is present in the brown cable, the monitor is switched on automatically and the camera is activated. ➤ Connect the white cable to the positive cable of the instrument panel illumination (6). 8 Using the monitor 8.1 Switching the monitor on and off (fig. b, page 7) ➤ Switch the ignition on. ➤ Switch the monitor on by pressing the ON/OFF switch (1). ✓ The picture appears. I Note If you have completely connected all of the monitor cables, the brightness should be automatically reduced when the driving lights are switched on. ➤ Switch the monitor off with the ON/OFF switch (1). ✓ The picture disappears. ➤ When the ignition is turned on, the monitor should switch on as soon as reverse gear has been selected. ➤ Switch out of reverse and the system switches back to stand-by. 8.2 Setting the monitor ➤ Set the brightness and contrast as required. The inverter is located on the rear of the monitor (blue dip switch, fig. b 5, page 7) for normal or inverted display on the monitor. With the inverted display, the monitor acts as though you were looking in the rear-view mirror of your vehicle. MIRROR dip switch in bottom position: Inverted display MIRROR dip switch in top position: Normal display ➤ Decide which type of display you want and switch the dip switch into the required position. 9 Cleaning and maintaining the monitor e Caution! Remove the cable before cleaning the monitor to prevent short circuiting. a Caution Do not use sharp or hard objects or cleaning agents for cleaning as these may damage the device. 35
Page 1 and 2: _M45.book Seite 1 Freitag, 21. Nove
Page 11 and 12: _M45.book Seite 11 Freitag, 21. Nov
Page 33: _M45.book Seite 33 Freitag, 21. Nov
Page 85 and 86:
_M45.book Seite 85 Freitag, 21. Nov
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
_M45.book Seite 101 Freitag, 21. No
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
show all

MOBITRONIC M45R - Waeco

Create successful ePaper yourself

Delete template?

Save as template?