Nutensteine, Schrauben und Zubehör Slot stones, screws ... - Aratron
Nutensteine, Schrauben und Zubehör Slot stones, screws ... - Aratron
Nutensteine, Schrauben und Zubehör Slot stones, screws ... - Aratron
Sie wollen auch ein ePaper? Erhöhen Sie die Reichweite Ihrer Titel.
YUMPU macht aus Druck-PDFs automatisch weboptimierte ePaper, die Google liebt.
Flächenelemente <strong>und</strong> <strong>Zubehör</strong><br />
Surface elements and accessories<br />
Schiebetürprofil<br />
Sliding door profile<br />
Das Schiebetürprofil wird in die<br />
Längsnut des BLOCAN ® -Profils eingebracht.<br />
Danach wird der R<strong>und</strong>stab<br />
in das untere Schiebetürprofil<br />
eingelegt. Wie in der Abbildung<br />
dargestellt, können jetzt die Flächenelemente<br />
eingesetzt werden.<br />
Material: PVC schwarz<br />
Plattenzuschnittmaß:<br />
Rahmeninnenhöhe -17mm bei<br />
6mm Flächenelementen bzw.<br />
-22mm bei 8mm Flächenelementen.<br />
Bei Schiebetüren mit Profilrahmen<br />
ist das Gleitstück auf Seite 170 oder<br />
das Laufrollen-Modul im Kapitel IV<br />
- Seite 43 zu verwenden.<br />
ohne R<strong>und</strong>stab<br />
without bead-moulding<br />
mit R<strong>und</strong>stab<br />
with bead-moulding<br />
The sliding door profile is<br />
attached to the longit<strong>und</strong>inal<br />
slot. Afterwards the 6 mm<br />
bead-moulding is inlaid in the lower<br />
part of the sliding door profile.<br />
As shown in the picture<br />
surface elements can be now installed.<br />
Material: PVC black<br />
Panel depth allowanc:<br />
frame inside height -17mm for respectively<br />
surface elements 6 mm<br />
thick or -22mm for surface elements<br />
8 mm thick.<br />
For sliding doors with profile frames,<br />
the sliding block on page 170 or the<br />
roller module in chapter IV page 43)<br />
must be used.<br />
Code No. Type Nutgeometrie <strong>Slot</strong> geometry A B C D<br />
[mm]<br />
E<br />
mit R<strong>und</strong>stab with bead-moulding<br />
4.000552 Zuschnitt cut 30 19 15 6,2 6,2 2<br />
4.000550 Stange bar 30 19 15 6,2 6,2 2<br />
4.010552 Zuschnitt cut 40 19 15 6,2 6,2 2<br />
4.010550 Stange bar 40 19 15 6,2 6,2 2<br />
4.010554 Zuschnitt cut 40 28 17,5 8,3 8,3 6<br />
4.010553 Stange bar 40 28 17,5 8,3 8,3 6<br />
ohne R<strong>und</strong>stab without bead-moulding<br />
4.000553 Zuschnitt cut 30 19 15 6,2 6,1 2<br />
4.000551 Stange bar 30 19 15 6,2 6,1 2<br />
4.010555 Zuschnitt cut 40 19 15 6,2 6,1 2<br />
4.010551 Stange bar 40 19 15 6,2 6,1 2<br />
4.010557 Zuschnitt cut 40 28 17,5 8,3 8,3 6<br />
4.010556 Stange bar 40 28 17,5 8,3 8,3 6<br />
II - 136 RK Rose+Krieger GmbH & Co. KG � Postfach 15 64 � D-32375 Minden