Ledger Connector - Durisol Building Systems Inc.

INSTALLATION OF ICFLC:
Snap a line for the bottom of the ledger and
mark off the required on center spacing.
Cut vertical kerfs at the marked location
on the ICF. Bottom of ICFLC is 1" below
chalk line.
Insert an ICFLC bracket through each cut.
Glue is recommended on the exposed
flange to the ICF.
Place the concrete (f′ c = 2500 psi).
NOW AVAILABLE AT:
Patent Pending
Wood Ledger
ATTACHMENT OF WOOD LEDGER:
Slip the ICFLC-W underneath the wood ledger.
Attach the 6 screws partially into the ledger.
Position the ICFLC-W with the ledger bottom
level with chalk line and drive the screws
through the wood and the ICFLC.
The ICFLC and ICFLC-W ledger connector
system is engineered to solve the challenges
of mounting steel or wood ledgers on
the Durisol Wall Form.
Simpson's ledger connector system is easy,
quick and versatile to use. The perforations
in the embedded leg of the ICFLC permit the
concrete to flow around it anchoring the
ICFLC securely within the block. The exposed
flange provides a structural surface for
mounting either a wood or a steel ledger.
Material: ICFLC—14 gauge; ICFLC-W and
ICFLC-CW—16 gauge.
Finish: Galvanized.
67 Frid Street
Hamilton, Ontario
Canada L8P 4W3
(905) 521-0999
Steel Ledger
ATTACHMENT OF STEEL LEDGER:
• Position the steel ledger against the
ICFLC and drive the required number
of screws through the steel ledger into
the ICFLC.
All screws shall be located at least ¹⁄₂"
from the edge of the ICFLC.
Space screws evenly.
Page 1 of 2
Toll Free: U.S.A. 800-999-5099 • Canada 800-465-1515 © Copyright 2002 Simpson Strong-Tie Co., Inc. Form F-ICFDIST02 11/02 exp 1/05
www.strongtie.com Printed in the USA

GENERAL NOTES:
1. Spacings shown apply to vertical loads only.
2. No load duration increase is allowed.
3. Minimum concrete compressive strength (f'c) is 2500 psi.
4. The allowable download for ICFLC on forms up to 2¹⁄₂" thick is
2235 lbs. Canadian factored resistance is 3280 lbs.
STEEL LEDGER – ICFLC
Download
2060
Download
Ledger
Thickness
68 mils (0.068")
54 mils (0.054")
ICF LEDGER CONNECTOR SYSTEM
Spacing to Replace Anchor Bolts
¹⁄₂" Diameter Bolts ⁵⁄₈" Diameter Bolts
12" o.c.
1'
1'-3"
24" o.c.
2'
2'-3"
12" o.c.
9"
1. Minimum steel ledger specification is A-653 SS Grade 50.
2. Use three ¹⁄₄-14 x³⁄₄", #3 drill point screws (not provided).
Minimum screw shear capacity is 750 lbs.
Canadian factored resistance is 2990 lbs.
Spacing shall be determined by the project design professional.
SPACING ON DIFFERENT GAUGE STEEL LEDGERS:
This example shows ICFLC spacing to replace ¹⁄₂" diameter Anchor
Bolts installed at 12" o.c. on 14 gauge and 16 gauge steel ledgers.
NOTE: Spacing is based on a combination of ledger gauge and anchor
bolt diameter. Spacing is closer for a 14 gauge ledger to achieve the
same bolt/ledger capacity.
SOLID SAWN WOOD LEDGER – ICFLC with ICFLC-W
Download
1920
1920
1. Use six D3 screws (provided).
2. Loads assume a minimum Spruce-Pine-Fir ledger.
Canadian factored resistance is 3145 lbs.
Spacing shall be determined by the project design professional.
LVL LEDGER – ICFLC with ICFLC-CW
Spacing to Replace Anchor Bolts
24" o.c.
1'-6"
2'
¹⁄₂" Diameter Bolts
⁵⁄₈" Diameter Bolts
1920 12" o.c. 24" o.c. 36" o.c. 48" o.c. 12" o.c. 24" o.c. 36" o.c. 48" o.c.
4' 4' 4' 4' 3'-6" 4' 4' 4'
(2) ⁵⁄₈" Diameter Bolts
³⁄₄" Diameter Bolts
1920 12" o.c. 24" o.c. 36" o.c. 48" o.c. 12" o.c. 24" o.c. 36" o.c. 48" o.c.
1'-9" 3'-6" 4' 4' 2'-9" 4' 4' 4'
1. Use six D3 screws (provided).
Canadian factored resistance is 3145 lbs.
Spacing shall be determined by the project design professional.
SIMPSON STRONG-TIE COMPANY, INC.
1'
Spacing to Replace Anchor Bolts
¹⁄₂" Diameter Bolts
⁵⁄₈" Diameter Bolts
12" o.c. 24" o.c. 36" o.c. 48" o.c. 12" o.c. 24" o.c. 36" o.c. 48" o.c.
4' 4' 4' 4' 3'-9" 4' 4' 4'
(2) ⁵⁄₈" Diameter Bolts
³⁄₄" Diameter Bolts
12" o.c. 24" o.c. 36" o.c. 48" o.c. 12" o.c. 24" o.c. 36" o.c. 48" o.c.
1'-9" 3'-9" 4' 4' 3'-6" 4' 4' 4'
Requires 3
screws at each
location.
Table provides on
center spacing.
Typical Steel Ledger
Installation with ICFLC
(Minimum 16 gauge steel ledger)
Maximum
2⁵⁄₈"
ICFLC
Installation
Side View
This flier is effective until January 31, 2005 and reflects information available as of November 1, 2002. This information is updated periodically and
should not be relied upon after January 31, 2005; contact Simpson for current product information and limited warranty or see www.strongtie.com.
Page 2 of 2
Home Office Northwest USA Southwest USA Southeast USA Northeast USA Canada Warehouses
4120 Dublin Blvd., Ste 400 1450 Doolittle Dr 260 N. Palm St 1720 Couch Dr 2600 International St 5 Kenview Blvd. Enfield, CT
Dublin, CA 94568 San Leandro, CA 94577 Brea, CA 92821 McKinney, TX 75069 Columbus, OH 43228 Brampton, Ontario L6T5G5 Jacksonville, FL
FAX: 925/833-1496 FAX: 510/632-8925 FAX: 714/871-9167 FAX: 972/542-5379 FAX: 614/876-0636 FAX: 905/458-7274 Kent, WA
Langley, B.C.
Toll Free: U.S.A. 800-999-5099 Canada 800-465-1515 © Copyright 2002 Simpson Strong-Tie Co., Inc. Form F-ICFDIST02 11/02 exp 1/05
www.strongtie.com Printed in the USA
14 ga
16 ga
Typical Wood Ledger
Installation
with ICFLC and ICFLC-W
[ICFLC-CW (for LVL Ledger) similar]
ICFLC
MISINSTALLATION!