to download the Blasting and Explosives - Dyno Nobel

More documents

Recommendations

Info

Bulk products TITAN ® Emulsion Product % ANFO (wt%) Density* (g/cm 3 ) Energy (MJ/kg) Recomm minimum hole diameter (mm) TITAN 2000G (Gassed) 0 1.05 – 1.25* 2.5 102 TITAN 2070G (Gassed) 30 1.05 – 1.25* 2.9 102 TITAN 2060G (Gassed) 40 1.05 – 1.25* 3.0 102 TITAN 2050G (Gassed) 50 1.20 – 1.25* 3.1 102 TITAN 2050 (Blend) 50 1.32 # 3.1 203 TITAN 2040 (Heavy ANFO) 60 1.25 # 3.2 127 TITAN 2030 (Heavy ANFO) 70 1.10 # 3.3 102 TITAN 2020 (Heavy ANFO) 80 0.97 # 3.4 102 TITAN 3000G (Gassed) 0 1.05 – 1.25* 2.7 76 TITAN 3070G (Gassed) 30 1.05 – 1.25* 3.0 76 TITAN 3060G (Gassed) 40 1.05 – 1.25* 3.1 89 TITAN 3040 (Heavy ANFO) 60 1.23 # 3.3 127 TITAN 3030 (Heavy ANFO) 70 1.05 # 3.4 102 TITAN 3020 (Heavy ANFO) 80 0.93 # 3.5 89 TITAN 5000G (Gassed) 0 1.05 – 1.25* 2.7 102 TITAN 5070G (Gassed) 30 1.05 – 1.25* 3.0 102 TITAN 5060G (Gassed) 40 1.05 – 1.25* 3.1 102 TITAN 5050 (Heavy ANFO) 50 1.31 # 3.2 203 TITAN 5040 (Heavy ANFO) 60 1.21 # 3.3 152 TITAN 5030 (Heavy ANFO) 70 1.05 # 3.4 102 TITAN 5020 (Heavy ANFO) 80 0.94 # 3.5 102 TITAN 7000 (Gassed) 0 0.80 – 1.25 2.9 35 TITAN 7000i (Gassed) 0 0.80 – 1.25 2.9 35 TITAN 7000SX (Gassed) 0 0.80 – 1.25 2.8 35 * Inhole gassed product density is dependent on hole depth. # Densities may vary due to variations in the AN prill density. For blends with 50% emulsion or greater, please consult your Dyno Nobel representative to ensure the product is suitable for your application. © Dyno Nobel Asia Pacific Pty Limited 2012. Reproduction without permission is strictly prohibited.
Bulk products How to select the right TITAN 2000 product for your needs The table below is a guide to choosing the right product for the blast hole condition and desired performance. Please consult your Dyno Nobel representative for more indepth advice. Product selection guide – blast hole condition Product Emulsion % 1 10 20 30 40 50 60 70 80 90 100 Dry Blast Hole Conditions 2 Use Yes MST 3 (days) 14 14 14 14 14 14 14 14 14 14 Dewatered 4 Use No Yes MST 3 (days) – – – 5 8 12 12 12 12 12 Wet 5 Use No Yes MST 3 (days) – – – – – 8 12 12 12 12 Dynamic 6 Use No Yes MST 3 (days) – – – – – – 5 8 8 8 Product Sensitisation Required No Note Use 7 Yes 8 Delivery Method A A A A A/P A/P A/P A/P A/P A/P NOTES: 1. Dyno Nobel emulsion blend names have a prefix indicating the emulsion type and a suffix indicating the emulsion weight %, with the remaining composition being ANFO. The addition of the letter “G” at the end indicates whether the product is gas sensitised eg TITAN 2070G = TITAN 2000 gassed blend containing 70 wt% emulsion or TITAN 2040 = TITAN 2000 heavy ANFO blend containing 40 wt% emulsion. 2. Dry hole is defined as a blast hole containing no water including no wet walls. 3. MST = Maximum Sleep Time (days). These figures represent the average combined known performance results derived from laboratory testing and observed use in the field by customers over many years. The MST is a guide for when the product is used in best case conditions and is likely to be less in practice. 4. A dewatered hole is defined as not recharging with water. 5. A wet hole is defined as a blast hole containing static water. 6. Dynamic water is defined as a recharge rate of >1m in 30 mins. If significant dynamic water is present, the suggested MST should be reduced. 7. Emulsion blends containing 50% emulsion are typically auger loaded. This product has reduced sensitivity and is recommended for hole depths
Page 1 and 2: Explosives Engineers' Guide
Page 3 and 4: The information provided in this br
Page 5 and 6: headline Glossary Airblast Airborne
Page 7 and 8: Rules of thumb These rules provide
Page 9 and 10: headline Volume table CUBIC METRES
Page 11 and 12: Gassing density for TITAN ® blends
Page 13 and 14: Properties of typical rock types Ma
Page 15 and 16: Airblast An airblast is an airborne
Page 17 and 18: Underground blast design Shoulder H
Page 19: Underground blast design Design of
Page 23 and 24: headline Packaged products DYNOSPLI
Page 25 and 26: Packaged products POWERMITE ® PRO
Page 27 and 28: Initiation systems - downhole NONEL
Page 29 and 30: Initiation systems - open-cut NONEL
Page 31 and 32: Initiation systems Cast Boosters TR
Page 33 and 34: Initiation systems SMARTSHOT ® Ele
Page 35 and 36: Blasting accessories DYNOSTART (DS2
Page 37 and 38: Blasting accessories Lo-Stat ANFO H
Page 39 and 40: New Explosives Engineers’ App n 7

to download the Blasting and Explosives - Dyno Nobel

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?