SUBMITTAL SHEET - Grabber Construction Products

Submittal Sheet #03090414
Wafer Head Driller
SUBMITTAL SHEET
Product: Item# Description Unit Pack
234 Wafer Head Driller, Black Phosphate, 8 x 1/2”, Bulk 10 M
234FZ Wafer Head Driller 8 x 1/2”, Bulk 10 M
234Z Wafer Head Driller 8 x 1/2”, Bulk 10 M
34Z Wafer Head Driller 8 x 1/2”, Bulk 10 M
34ZA Wafer Head Driller 8 x 1/2” (zinc), Bulk 10 M
35Z Wafer Head Driller 8 x 1”, Bulk 5 M
235Z Wafer Head Driller 8 x 1”, Bulk 5 M
236Z Wafer Head Driller 8 x 1 1/4”, Bulk 5 M
36Z Wafer Head Driller 8 x 1 1/4”, Bulk 5 M
36ZA Wafer Head Driller 8 x 1 1/4”, Bulk 5 M
37Z Wafer Head Driller 8 x 1 5/8”, Bulk 4 M
237FZ Wafer Head Driller 8 x 1-5/8”, Bulk 4 M
237Z Wafer Head Driller 8 x 1 5/8”, Bulk 4 M
376Z Wafer Head Driller 8 x 2”, Bulk 2.5 M
238Z Wafer Head Driller 8 x 2-1/2”, Bulk 2.5 M
39Z Wafer Head Driller 8 x 3”, Bulk 1 M
234Z10 Wafer Head Driller 10 x 3/4”, Bulk 5 M
234Z10CW Wafer Head Driller 10 x 3/4”, Bulk 5 M
234Z12CW Wafer Head Driller 12 x 3/4”, Bulk 5 M
Application: The GRABBER Wafer Head Drivall¨ is used to attach metal K lath, wire lath wood grounds, to lathers
channel structural studs, and metal decks. Also used for attaching steel studs to runners, 14-20
gauge steel.
Description: Low profile wafer head, #2 Phillips Recess Drive, Fine 16 TPI, silver zinc finish with extra sharp #2
point. Available in GrabberGard® Exterior Finish - Rated 1000 hr per ASTM B117. ( *All 234Z series
feature #3 point for faster cutting in heavier gauge steel.)
Directions: Use standard screw gun with depth sensitive nose piece. Suggested screw gun for optimium perfor
mance is 4 amps minimum and 0 to 4,000 rpm. Wafer head is completely seated when the head
base is flush with the work surface. Overdriving may result in failure of the fastener or stripping of
the head recess.
"If it's worth building, it's worth GRABBER®" www.grabberman.com
Page: 1/3

Submittal Sheet #03090414-H
SUBMITTAL APPROVALS:
JOB NAME
CONTRACTOR DATE
TRADEMARKS: NOTICE:
The following trademark used herein is owned by Grabber
Construction Products, Inc.: GRABBER.
We shall not be liable for incidental and consequential
damages, directly or indirectly sustained, nor for any loss
caused by application of these goods not in accordance with
current printed instruction or for other than the intended use.
Our liability is expressly limited to replacement of defective
goods. Any claim shall be (30) days of the date it was or
reasonably should have been discovered.
"If it's worth building, it's worth GRABBER®" www.grabberman.com
Page: 2/2

Submittal Sheet #03090414-H
Wafer
Head
Drill
Point
#2 Phillips
Drive
PRODUCT SPECIFICATIONS
Fastener ClassificationH eavy Gauge Metal
Fastener Head Wafer, Wafer, Type A
Fastener Drive #2 Phillips
Fastener Gauge #8, #10
Fastener Point Drill, #2.5 Drill, #3 Drill
Fastener Package Type Packaged Screws
Fastener Package Weight 1lb Box, 5 Pound, 5lb Box, Bulk Box
Features:
Wafer head, drill point framing screws for heavy
gauge metal applications. Wafer head provides a
greater bearing surface than Pan or Hex Drillers,
with a low-profile head exposure.
STANDARD CORROSION TEST RESULTS
Finish Test Standard/Protocol Results
Black/Gray PhosphateS alt Spray Results ASTM B117 24 hours, no red rust
Yellow Zinc Salt Spray Results ASTM B117 48 hours, no red rust
Clear ZincS alt Spray Results ASTM B117 24 hours, no red rust
Dracrotized Salt Spray Results ASTM B117 500 hours, no red rust
GrabberGard Salt Spray Results ASTM B117 1,000 hours, no red rust
GrabberGard Kesternich Results DIN 50018, 2.0L 15 cycles, no red rust
All GRABBER screw products are manufactured in facilities that are ISO 9002 and ISO 14001 certified and approved. The
fasteners comply with SAE J78 and ASTM C 954, as referenced in ICBO report ER-5280, and are approved for use by the
Uniform Building Code. ©2012 Grabber Construction Products, Inc. GRABBER®, STREAKER®, DRIVALL®, LOX®,
GRABBERGARD®, and SCAVENGER® are registered names or trademarks by Grabber Construction Products, Inc.
"If it's worth building, it's worth GRABBER®" www.grabberman.com
Page: 2/3