TRADE OF VEHICLE BODY REPAIR - eCollege

More documents

Recommendations

Info

Module 3– Unit 1 Figure 11: Snap 4 Tonne Standard Set Snap 4Tonne Standard Set Supplied for Carrying Case 1 Manual pump with hose 2 4-T bantam hydraulic hose. 18m 3 4-T ram toe 4 Extension tubes 5 Snap flex head 6 90º V base 7 Tube connector 8 Serrated saddle 9 Wedge head 10 Plunger toe 11 Chain pull collar 12 Spread ram – wedge ram 13 Flat base Vehicle Body Repairs - Phase 2 24
Module 3– Unit 1 Figure 12: Repairs to a Door Opening using a Push Ram Repairs to a door opening using a single Pull/Push, figure 12 shows rectification to a door opening using a push ram connected at both ends to push-pull clamps, which are bolted on to the door flange edges. The doors are left suspended on their hinges to act as templates during the operation. Figure 13: Push/Pull Realignment Equipment Repairs to boot lid aperture and rear windscreen using a combination of set-ups. Where the rear of the car becomes accidentally pushed in, the panels can be returned to there correct alignment in the manner illustrated in figure 13. The jack is placed across the aperture of the boot lid, with a wedge head attached to one end and the rubber flex head to the other. This is to spread the force of the pressure evenly over a larger area. Vehicle Body Repairs - Phase 2 25
Page 1 and 2: TRADE OF VEHICLE BODY REPAIR PHASE
Page 3 and 4: Table of Contents Use of Push/Pull
Page 5 and 6: Table of Figures Figure 1: Example
Page 7 and 8: Module 3- Unit 1 Use of Push/Pull E
Page 9 and 10: Module 3- Unit 1 Exercise Instructi
Page 11 and 12: Module 3- Unit 1 Safety Awareness S
Page 13 and 14: Module 3- Unit 1 Different Types of
Page 15 and 16: Module 3- Unit 1 Types of Chassis a
Page 17 and 18: Module 3- Unit 1 Figure 6: Body Con
Page 19 and 20: Module 3- Unit 1 Glass Fibre Compos
Page 21 and 22: Module 3- Unit 1 Clamping Method on
Page 23 and 24: Module 3- Unit 1 Clamping Procedure
Page 25 and 26: Module 3- Unit 1 Vehicle Body Repai
Page 27 and 28: Module 3- Unit 1 Appropriate Tools
Page 29: Module 3- Unit 1 Basic Equipment A
Page 33 and 34: Module 3- Unit 1 Spreading Spreadin
Page 35 and 36: Module 3- Unit 1 Example of use of
Page 37 and 38: Module 3- Unit 1 Downward Pulls to
Page 39 and 40: Module 3- Unit 1 Sway Damage pulls
Page 41 and 42: Module 3- Unit 1 Mash Damage Heat t
Page 43 and 44: Module 3- Unit 1 Every car is to be
Page 45 and 46: Module 3- Unit 1 Steels Steel is th
Page 47 and 48: Module 3- Unit 1 Use all of the thr
Page 49 and 50: Module 3- Unit 1 3. Lower vehicle o
Page 51 and 52: Module 3- Unit 1 Realignment, Pull
Page 53 and 54: Module 3- Unit 1 Selection of Appro
Page 55 and 56: Module 3- Unit 1 Self Assessment Qu
Page 57 and 58: Module 3- Unit 1 12. What is a fixe
Page 59 and 60: Module 3- Unit 1 Answers to Questio
Page 61 and 62: Module 3- Unit 1 13. 14. 15. 16. 17
Page 63: FÁS Learning Innovation Unit Apt.

TRADE OF VEHICLE BODY REPAIR - eCollege

Create successful ePaper yourself

Delete template?

Save as template?