JSC Catalog Vol. 6 - Jones Stephens Corporation
JSC Catalog Vol. 6 - Jones Stephens Corporation
JSC Catalog Vol. 6 - Jones Stephens Corporation
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>Jones</strong> <strong>Stephens</strong> Corp. • PlumBest • LTConnections<br />
DESCRIPTION<br />
Closed Cell Pipe Insulation is a<br />
fl exible and easy-to-apply tubing<br />
product available in Semi-Slit and<br />
Self-Sealing styles. These chemically<br />
inert pipe insulations are specially<br />
formulated to retard heat gain and<br />
their closed-cell structures allow them<br />
to function as effi cient insulators. The<br />
Self-Sealing version has yellow selfseal<br />
release liner that is both easy to<br />
see and peel.<br />
APPLICATIONS<br />
To reduce unwanted heat loss or heat<br />
gain, control condensation, decrease<br />
plumbing noise and maximize<br />
energy savings. They can be used on<br />
hot and cold water lines, refrigeration<br />
lines, air conditioning lines; line<br />
set tubing, condenser coils, and connection<br />
and distribution lines.<br />
Closed Cell Pipe Insulation has low<br />
thermal conductivity and a very low<br />
water vapor transmission rate. This<br />
low density product demonstrates excellent<br />
thermal, physical and chemical<br />
resistant properties, and has a<br />
broad service temperature range<br />
between -90° F and 180° F (-68° C<br />
and 82° C). It can be installed in<br />
commercial, industrial, and residential<br />
insulation projects.<br />
CLOSED CELL<br />
Pipe Insulation<br />
INSTALLATION<br />
Closed Cell Pipe Insulation is installed<br />
by sliding the stick over pipe or tubing.<br />
For existing lines, the insulation<br />
should be slit lengthwise and fi tted<br />
over the pipe. When in place, make<br />
sure all seams are adhered with contact<br />
adhesive and pressed together to<br />
form a seal. The Self-Sealing version<br />
does not require adhesive. Fittings<br />
can be fabricated from miter-cut<br />
tubular sections. Closed Cell Pipe<br />
Insulation is easily cut with a sharp<br />
knife.<br />
OUTDOOR APPLICATIONS<br />
Outdoor applications require a protective<br />
coating (high quality exterior<br />
acrylic latex paint) for optimum<br />
performance. For best appearance,<br />
two coats are recommended.<br />
UNDERGROUND<br />
For buried lines above the water<br />
table, use a clean fi ll such as sand<br />
(3”-5” layer) to protect Closed Cell<br />
Pipe Insulation before backfi lling. It is<br />
recommended that all materials to<br />
be buried are properly sealed at all<br />
seams and butt joints with Contact<br />
Adhesive. For optimum performance,<br />
the lines should be encased in conduit<br />
to protect them from problems<br />
associated with ground water.<br />
RESISTANCE TO MOISTURE<br />
VAPOR FLOW<br />
The closed-cell structure effectively<br />
retards the fl ow of moisture vapor,<br />
and is considered a low transmittance<br />
vapor retarder. For most applications,<br />
Closed Cell Pipe Insulation<br />
needs no additional protection.<br />
Toll Free Phone 1-800-35-JONES (355-6637) • Toll Free Fax 1-800-462-6991 • Website www.plumbest.com<br />
Poly Insulation<br />
Additional vapor barrier protection<br />
may be necessary for Closed Cell<br />
Pipe Insulation when installed on low<br />
temperature surfaces or where it is<br />
exposed to continuous high humidity.<br />
FLAME AND SMOKE RATING<br />
Closed Cell Pipe Insulation in wall<br />
thicknesses of 1” (25mm) and below<br />
has a fl ame spread rating of 25 or<br />
less and a smoke development rating<br />
of 50 or less as tested by ASTM E<br />
84; CAN/ULC-S102.2-M88 Method<br />
of Testing entitled: “Surface Burning<br />
Characteristics of Building Materials.”<br />
Numerical fl ammability ratings alone<br />
may not defi ne the performance of<br />
products under actual fi re conditions.<br />
They are provided only for use<br />
in the selection of products to meet<br />
limits specifi ed, when compared to a<br />
known standard.<br />
SPECIFICATION COMPLIANCE<br />
Complies with requirements of:<br />
ASTM E 84; CAN/ULC S102.2<br />
ASTM D 1622<br />
ASTM D 1171<br />
ASTM C 177 or C518<br />
ASTM E 96<br />
C<br />
105