M Series Pin and Socket Connectors

More documents

Recommendations

Info

60 36 Position 50 Position .156 +.005 -.000 3.96 +0.13 [ -.000 Dia. 4 Holes .173 [4.39] .016 [0.41] R 4 Plc. .130 +.005 -.000 3.30 +0.13 -.000 4 Plc. ] Dia. [ Recommended Panel Cutout .327 [8.31] Typ. ] .195 [4.95] Typ. .468 [11.89] R .407 [10.34] .815 [20.70] .016 [0.41] R .766 [19.45] 1.155 [29.33] .500 [12.70] Typ. Recommended Panel Cutout Material and Finish Housing—Phenolic per MIL-M-14, Type CFG; color, black Contacts—Brass per MIL-C-50; selective .000030 [0.00076] gold over .000050 [0.00127] nickel plated (gold plating per MIL-G-45204, nickel plating per QQ-N-290) Dimensions are shown for reference purposes only. .130 +.005 -.000 3.30 +0.13 -.000 or .218 +.005 -.000 5.54 +0.13 ] † -.000 [ [ .140 [3.56] Typ. 2.281 [57.94] 2.025 [51.44] .128 [3.25] Typ. M Series Pin and Socket Connectors 2.025 [51.44] 2.281 [57.94] Posted Connectors, .200 [5.08] Grid (Continued) ] †.218 [5.54] diameter is required when jackscrews are used. Plug Assemblies .300 [7.62] .365 [9.27] Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Specifications subject to change. Technical Support Center 1-800-522-6752 www.tycoelectronics.com Catalog 82003 Revised 3-01 No. of T e r m i n a t i o n P o s t P o s t C o n t a c t Plug Assembly Mates with Receptacle Assembly P o s . M e t h o d C o n f i g u r a t i o n L e n g t h † F i n i s h Part Number Part Number 1 5 W r a p - T y p e .300 [7.62] .365 [9.27] .915 [23.24] Plug Assembly (With Posted Pin Contacts) .915 [23.24] Plug Assembly (With Posted Pin Contacts) .780 [19.81] 1.110±.010 [28.19±0.25] .025 x .025 . 2 1 5 Sel. Gold/Nickel1 2 0 5 6 2 8 - 3 2 0 5 6 0 6 0.64 x 0.64 5 . 4 6 2.595±.020 [65.91±0.51] 2.595±.020 [65.91±0.51] 3 6 T E R M I - P O I N T .031 x .062 . 8 1 0 Sel. Gold/Nickel1 2 0 5 6 2 9 - 1 5 0 C l i p 0.79 x 1.57 2 0 . 5 7 2 0 5 6 3 0 - 1 1Gold flash over .000050 [0.00127] nickel on entire contact with .000030 [0.00076] gold to a distance of .200 [5.08] from mating end. Posts are plated tin-lead over copper. †Post length will accommodate up to 3 terminations. Extraction Tool—Part No. 305183. Refer to page 32 for contact specifications (Type III+, Size 16). Mating receptacle block using crimp, snap-in contacts for 36-Position Plug Assembly, order Part No. 203956-2. Mating receptacle block using crimp, snap-in contacts for 50-Position Plug Assembly, order Part No. 203622-2. Refer to the appropriate column of Application Chart for Hardware Selection Page 10 through Page 25. N o t e :36 position connector uses standard 50 position hardware. 50 position connector uses standard 75 position hardware.
Dimensions are shown for reference purposes only. M Series Pin and Socket Connectors Special Application Connectors Special Application Connectors are available in the following configurations: V.35 Shallow Block High Current Mixed High Voltage RFI/EMI Shielded Grounding Blocks V.35 Connector The 34 position V.35 Connector is fully assembled and ready for placement on a printed circuit board. They are also available in kit form for cable assembly. These AMP V.35 connectors meet the requirements of 408-2593 for CCITT V.35 interfacing. High current connectors a r e designed for applications requiring up to 25 amperes of current. They are available in 12-position male and female housings which have rectangular contact cavities for accepting Type XII c o n t a c t s . Mixed connectors a r e d e s i g n e dfor applications that require intermixing signal, power and/or coaxial circuits in the same connector Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. housing. Housings are available in 15-, 16-, 29 CF (center fastener) and 42-position sizes and, depending upon the specific configuration, will accept Multimate contacts, Type I and Miniature, Standard and Twin Standard COAXICON contacts. The rectangular contact cavities accept Type XII contacts. High voltage connectors a r e designed for high voltage applications using Multimate contacts. The cavity centerline spacings and the silo construction of the contact cavities increase the current creepage path for higher voltage ratings. Housing sizes include 20 and 28 positions. RFI/EMI shielding kits provide shielding capabilities a g a i n s tradio frequency and electromagnetic interferences. Special 104-position h o u s i n g s accept Multimate contacts and are especially designed for use with shielding hardware. These shielding kits cannot be used with the standard 104-position connector housings. Specifications subject to change. Technical Support Center 1-800-522-6752 www.tycoelectronics.com Catalog 82003 Revised 3-01 Grounding blocks are ideally suited for aircraft applications, where shielded cable is to be grounded to an airframe. The ground wires of shielded cables are pigtailed off with ferrules and are crimped to Size 16 s o c k e tcontacts. The contacts are loaded into a standard 14- or 3 4 - p o s i t i o n connector housing. This connector then can be mated to the grounding block which is fastened to the aircraft frame. Grounding blocks have Size 16 screw-machined p i n contacts which are staked, r i veted and soldered into the L-shaped metal bracket. The bracket has fixed jackscrew receptacles that will accept the special turnable jackscrews fastened to the mating socket connector half. 61
Page 1 and 2:
M Series Pin and Socket Connectors
Page 3 and 4:
Dimensions are shown for reference
Page 5 and 6:
Dimensions are shown for reference
Page 7 and 8:
The total current capacity of each
Page 9 and 10: Dimensions are shown for reference
Page 11 and 12: 1. Confirm that Application A (at l
Page 31 and 32: Type III+, Crimp, Snap-In Material
Page 33 and 34: Type III+, Crimp, Snap-In Contact S
Page 35 and 36: Type III+, Solder Versions (Continu
Page 37 and 38: High Current Upgrade Type II and Ty
Page 39 and 40: High Current Upgrade Type XII, Crim
Page 41 and 42: Subminiature, Crimp, Snap-In, Size
Page 43 and 44: Miniature, Crimp, Snap-In, Size 12
Page 45 and 46: 6 Position .688 [17.48] .054 [1.37]
Page 47 and 48: 26, 34 and 36 Positions (Continued)
Page 49 and 50: 75 Position .327 [8.31] 2.281 [57.9
Page 51 and 52: 160 CF Position (with Center Fasten
Page 53 and 54: 6 Position .054 [1.37] .580 .688 [1
Page 55 and 56: 34 Position .118 [3.00] Typ. 1.686
Page 57 and 58: 75 Position .327 [8.31] .016 [0.41]
Page 59: Receptacle Assembly 15 Position Rel
Page 65 and 66: Right-Angle Plug Assembly Material
Page 67 and 68: Vertical Plug Assembly Material and
Page 69 and 70: Cable Connector Kits, 34 Position,
Page 71 and 72: Cable Connector Kits, 34 Position,
Page 73 and 74: Mixed 29 CF Position (with Center F
Page 75 and 76: High Voltage 20 Position UL Voltage
Page 77 and 78: Grounding Blocks Material and Finis
Page 81 and 82: Sub Guide Head Pins and Sockets Sub
Page 83 and 84: Pin Hoods, External Closed-End and
Page 87 and 88: Shields,Two-Piece, 45° and 30° Ca
Page 89 and 90: Keying Plug (for Multimate Contact
Page 91 and 92: Application Tooling/Technical Docum
Page 95 and 96: Note: This numerical index lists al
show all

M Series Pin and Socket Connectors

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?