SCIENCE TEST

Answer: G.
In Experiment 1, only Liquid 1 is pure ethanol. The density of the Liquid 1 was found to
be 0.793 g/mL, so this is the measure of pure ethanol that was taken.
23. Based on the results of Experiments 1−3, the density of PA-11 is most likely:
potassium iodide (KI) was dissolved
O. A dry 100 mL graduated
A.
cylinder
less than 0.793 g/mL.
lance and tared. The solution B. between was 0.853 g/mL and 0.958 g/mL.
ed cylinder until the volume C. between was 0.999 g/mL and 1.05 g/mL.
f the liquid was then calculated. D. greater Thethan
1.11 g/mL.
d with different amounts of KI and
Table 2
Answer: C.
Mass of
Mass of solution in
KI in graduated
solution cylinder Density
(g) (g) (g/mL)
in a known mass of H 2O. A dry 100 mL graduated cylinder
was placed on the balance and tared. The solution was
added to the graduated cylinder until the volume was
50.0 mL. The density of the liquid was then calculated. The
procedure was repeated with different amounts of KI and
H 2O (see Table 2).
Table 2
Mass of
Mass of Mass of solution in
H 2O in KI in graduated
solution solution cylinder Density
Liquid (g) (g) (g) (g/mL)
6 97.66
7 95.41
8 94.38
9 92.18
10 87.77
Experiment 3
7.36
15.52
20.68
29.08
41.31
52.51
55.70
57.53
60.63
64.64
1.05
4
1.11
1.15
1.21
1.29
A solid plastic bead was placed at the bottom of a
ed the following experiments Experiment 3 to sample of each of Liquids 1−10 from Experiments 1 and 2.
f common plastics.
A solid plastic bead was If ACT-64E-PRACTICE
placed the bead at the stayed bottom at of the a sample bottom, of each “S” of was Liquids recorded 1−10 from in Experiments 1 and
2. If the bead stayed at Table the bottom, 3. If the “S” bead was recorded rose, “R” in was Table recorded 3. If the in bead Table rose, 3. “R” The was 50recorded
in
Table 3. The procedure procedure was repeated was for repeated various for plastics. various plastics.
Table 3
raduated cylinder was placed on an
d tared (the balance was reset to
ed to the graduated cylinder until a
Liquid
ned. Ethanol was added to the gradu- Plastic 1 2 3 4 5 6 7 8 9 10
volume of liquid was 50.0 mL. The
was then calculated. The procedure
ferent amounts of ethanol and H2O Polybutylene
VLDPE
LDPE
R
S
S
R
R
S
R
R
S
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
HDPE S S S S R R R R R R
PA-11 S S S S S R R R R R
PA-6 S S S S S S S R R R
Table 1
Polycarbonate
PVC
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
R
S
R
S
Mass of Total
ethanol
(g)
39.67
32.43
25.23
12.47
mass Density
(g) 22. In (g/mL) Experiment 1, the density of ethanol was found to be:
F. less than 0.793 g/mL.
39.67 G. 0.793 0.793 g/mL.
42.67
H.
0.853
0.999 g/mL.
45.02 0.900
47.89 J. 0.958 greater than 0.999 g/mL.
0 49.96 0.999
22. In Experiment 1, the density of ethanol was found to
be:
F. less than 0.793 g/mL.
G. 0.793 g/mL.
H. 0.999 g/mL.
J. greater than 0.999 g/mL.
23. Based on the results of Experiments 1−3, the density of
22. In Experiment 1, the density of
be:
F. less than 0.793 g/mL.
G. 0.793 g/mL.
H. 0.999 g/mL.
J. greater than 0.999 g/mL.
23. Based on the results of Experime
PA-11 is most likely:
A. less than 0.793 g/mL.
B. between 0.853 g/mL and 0.9
C. between 0.999 g/mL and 1.0
D. greater than 1.11 g/mL.
GO ON TO T