Download PDF (5.2 MB) - IBM Redbooks

More documents

Recommendations

Info

SP System M/T 9076 Tall Frame Thin SP Node Wide SP Node High SP Node SP Switch CWS SP Switch Router SP Ethernet Connection SP Switch Connection RS232C Connection Figure 1-1 RS/6000 SP system sample configuration As shown in Figure 1-1: ► The thin, wide, and high SP nodes, and the SP Switch are mounted in a tall frame. ► The SP nodes and SP Switch Router are connected to the SP Switch. ► The SP nodes and the SP Switch Router are connected to the SP Ethernet interface of the CWS. ► The frame with the SP nodes and the SP Switch are connected to the RS-232 interface of the CWS. 10 RS/6000 SP and Clustered <strong>IBM</strong> ^ pSeries Systems Handbook
SP System M/T 9076 Tall Frame SP Node SP Switch SP-Attached Servers MIT 7017 MIT 7026 CWS SP Ethernet Connection SP Switch Connection RS232C Connection Figure 1-2 RS/6000 SP system with SP-attached servers sample configuration Figure 1-2 shows an RS/6000 SP system with SP-attached servers sample configuration: ► The SP node and the SP Switch are mounted in a tall frame. ► The SP-attached servers (M/T 7017 and M/T 7026) are housed in their own frames. ► The SP node and the SP-attached servers are connected to the SP Switch. ► The SP node and the SP-attached servers are connected to the SP Ethernet interface of the CWS. ► The frame with the SP node and the SP Switch, and the SP-attached servers are connected to the RS-232 interface of the CWS. Chapter 1. Introduction 11
Page 1: RS/6000 SP and Clustered IBM ^ pSer
Page 4 and 5: Take Note! Before using this inform
Page 6 and 7: iv RS/6000 SP and Clustered IBM ^ p
Page 8 and 9: 2.3.3 Options . . . . . . . . . . .
Page 10 and 11: 3.4.4 SP-attached servers connectiv
Page 12 and 13: 8.2.4 IBM Short Wave Serial HIPPI P
Page 14 and 15: 10.2.2 SP system with SP-attached s
Page 16 and 17: xiv RS/6000 SP and Clustered IBM ^
Page 18 and 19: 7-1 Control workstation interface .
Page 20 and 21: 9-2 Software requirements for GPFS
Page 22 and 23: since 1996. His areas of expertise
Page 24 and 25: ibm.com/redbooks ► Send your comm
Page 26 and 27: 1.1 Overview on RS/6000 SP and Clus
Page 28 and 29: The SP universal cluster system (SP
Page 30 and 31: The SP/CES processor nodes incorpor
Page 32 and 33: Commercial computing users implemen
Page 36 and 37: Stand-alone Switch Tall Frame SP Sw
Page 38 and 39: Thin nodes The thin nodes occupy ha
Page 40 and 41: 1.4.3 Extension nodes Frames have l
Page 42 and 43: ► RS/6000 44P Model 170 (7044-170
Page 44 and 45: ► Parallel applications (applicat
Page 46 and 47: Load Balancer Load Balancer Figure
Page 48 and 49: 24 RS/6000 SP and Clustered IBM ^ p
Page 50 and 51: 2.1 SP internal node The basic RS/6
Page 52 and 53: 2.2.1 375 MHz POWER3 processor The
Page 54 and 55: 2.2.2 System memory 2.2.3 I/O subsy
Page 56 and 57: 2.2.5 System firmware and RTAS The
Page 58 and 59: Figure 2-4 375 MHz POWER3 High Node
Page 60 and 61: Figure 2-5 375 Mhz POWER3 SMP Wide
Page 62 and 63: ► Four memory slots supporting up
Page 64 and 65: 2.3.6 Disk requirements and options
Page 66 and 67: Expansion units can be mounted in t
Page 68 and 69: 2.4.3 Options ► An upgraded power
Page 70 and 71: 2.4.6 Hard disk drive requirements
Page 72 and 73: 2.5 375 MHz POWER3 SMP Thin Node (F
Page 74 and 75: 2.5.5 Memory requirements and optio
Page 76 and 77: Switch adapters for these nodes are
Page 78 and 79: 2.6.3 6xx bus 2.6.4 System memory 2
Page 80 and 81: 2.7.3 Options ► Two Processors (o
Page 82 and 83: 2.7.6 Disk requirements and options
Page 84 and 85:
Each expansion unit (or pair of uni
Page 86 and 87:
MX Bus 64-bit 400 MB/sec. SP Switch
Page 88 and 89:
Since the L2 cache maintains inclus
Page 90 and 91:
2.8.6 PCI I/O bridges is 400 MBps,
Page 92 and 93:
2.9.3 Requirements ► ARTIC960Hx 4
Page 94 and 95:
2.9.6 Memory requirements and optio
Page 96 and 97:
The 332 MHz SMP thin node occupies
Page 98 and 99:
- Frame-to-frame HACMP cable (F/C 3
Page 100 and 101:
76 RS/6000 SP and Clustered IBM ^ p
Page 102 and 103:
3.1 Overview The RS/6000 SP system,
Page 104 and 105:
processors, determines that the num
Page 106 and 107:
► Industry-standard PCI subsystem
Page 108 and 109:
Product positioning The 7017-S85 se
Page 110 and 111:
Up to three additional 7017-S80 I/O
Page 112 and 113:
► Industry-standard PCI subsystem
Page 114 and 115:
Description The 7017-S7A is package
Page 116 and 117:
► Choice of power from 4, 8, or 1
Page 118 and 119:
The 7017-S70 provides outstanding p
Page 120 and 121:
Machine type and Model 7017-S85 701
Page 122 and 123:
Description The 7026-M80 delivers a
Page 124 and 125:
► Internal I/O system scalability
Page 126 and 127:
The 7026-M80 is targeted at the key
Page 128 and 129:
Combined with an array of industry
Page 130 and 131:
Chipkill DIMMs for the 7026-6H1 pro
Page 132 and 133:
In addition, an HACMP packaged solu
Page 134 and 135:
► Support for 32-bit and 64-bit a
Page 136 and 137:
- Keyboard and mouse ports These ar
Page 138 and 139:
a serial number protected model con
Page 140 and 141:
Note: ► Memory standard/maximum i
Page 142 and 143:
Because the SP-attached server has
Page 144 and 145:
3. You must make several cable conn
Page 146 and 147:
For a complete listing of currently
Page 148 and 149:
You must install a frame-to-frame,
Page 150 and 151:
If used, the adapter must be ordere
Page 152 and 153:
3.4.4 SP-attached servers connectiv
Page 154 and 155:
2. You must make several cable conn
Page 156 and 157:
If you plan to attach an existing 7
Page 158 and 159:
Note: With F/C 9122 RS/6000 Server
Page 160 and 161:
Note: With F/C 9122 RS/6000 Server
Page 162 and 163:
2. Configure Service Director on ea
Page 164 and 165:
4.1 Frames The SP processor nodes c
Page 166 and 167:
All new designs are completely comp
Page 168 and 169:
4.1.3 SP frame redundant power supp
Page 170 and 171:
Tall frames contain a SEPBU power s
Page 172 and 173:
Note: Alternate two-stage switch co
Page 174 and 175:
F/C 1550 is the base offering for t
Page 176 and 177:
Note: If the switch used in this co
Page 178 and 179:
4.7 Short frame Short frames are av
Page 180 and 181:
4.8.2 Model 500 switched configurat
Page 182 and 183:
158 RS/6000 SP and Clustered IBM ^
Page 184 and 185:
5.1 SP Switch The design objectives
Page 186 and 187:
crossbar requests on a least recent
Page 188 and 189:
An SP Switch adapter is designed fo
Page 190 and 191:
Table 5-1 shows the AIX, PSSP, and
Page 192 and 193:
For upgrades to greater than eight
Page 194 and 195:
For systems that require only singl
Page 196 and 197:
5 Figure 5-7 illustrates single-sta
Page 198 and 199:
Note: 5.8 SP Switch2 1. Frames 1 to
Page 200 and 201:
- This is a new page listing for Et
Page 202 and 203:
Note: ► The SP Switch2 and its ad
Page 204 and 205:
The 740 microprocessor The 740 micr
Page 206 and 207:
6.1 The 9077 SP Switch Routers The
Page 208 and 209:
Processor Nodes SP System SP Switch
Page 210 and 211:
Figure 6-4 Rear view of SP Switch R
Page 212 and 213:
6.3.3 Network media card requiremen
Page 214 and 215:
SP system Both the SP Switch cable
Page 216 and 217:
- ATM - FDDI ► Frame to frame gro
Page 218 and 219:
Page 220 and 221:
7.1 Overview You may consider the c
Page 222 and 223:
7.2 Installation requirements The c
Page 224 and 225:
► At least 9 GB of disk storage.
Page 226 and 227:
Table 7-2 Serial port adapters for
Page 228 and 229:
► PSSP 3.2 (5765-D51) (or later).
Page 230 and 231:
EIA-232/422 (PCI) 2968 10/100 Mbps
Page 232 and 233:
0838 AIX 4.3 Update CD 1 0857 AIX 4
Page 234 and 235:
1.44MB 3.5-in Diskette Drive 1 Inte
Page 236 and 237:
6324 Primary I/O Drawer, 5 EIA 1 65
Page 238 and 239:
Adapter 6324 Primary I/O Drawer, 5
Page 240 and 241:
3153 18.2 GB 10K RPM 1" Ultra3 SCSI
Page 242 and 243:
*** SOFTWARE *** Product Descriptio
Page 244 and 245:
5765-C34 AIX Version 4 1 4061 AIX 4
Page 246 and 247:
. Frame Supervisor Cable SPVG SDR a
Page 248 and 249:
► Two licenses for IBM C for AIX
Page 250 and 251:
Note: Refer to Appendix C, “SP sy
Page 252 and 253:
8.1 PCI Communication adapters supp
Page 254 and 255:
Feature code Adapter ID 4951 9-Z IB
Page 256 and 257:
► Network adapter software provid
Page 258 and 259:
8.2.6 IBM Network Terminal Accelera
Page 260 and 261:
Unique features of FDDI-UP DAS The
Page 262 and 263:
This adapter provides a single DB-7
Page 264 and 265:
8.2.15 Turboways 622 Mbps PCI MMF A
Page 266 and 267:
Feature characteristics This featur
Page 268 and 269:
► Installation instructions Custo
Page 270 and 271:
► Supports half duplex operations
Page 272 and 273:
► Diskette with adapter device dr
Page 274 and 275:
► Network equipment such as a MAU
Page 276 and 277:
Feature characteristics This featur
Page 278 and 279:
8.2.33 SCSI-2 F/W Differential adap
Page 280 and 281:
single speed supported is 1.0625 Gb
Page 282 and 283:
Feature components This feature ord
Page 284 and 285:
Page 286 and 287:
9.1 Parallel System Support Program
Page 288 and 289:
9.1.3 System monitoring and control
Page 290 and 291:
This isolation is useful for correc
Page 292 and 293:
9.2.1 Administration and operation
Page 294 and 295:
9.3 LoadLeveler 9.3.1 Administratio
Page 296 and 297:
9.3.3 New in LoadLeveler 2.2 LoadLe
Page 298 and 299:
9.4.1 Operations ESSL’s mathemati
Page 300 and 301:
9.4.4 New in OSLp 1.3 ► Reduce a
Page 302 and 303:
9.5.1 Operation 9.5.2 New in PE 3.1
Page 304 and 305:
9.5.3 Software requirements Table 9
Page 306 and 307:
9.6.2 Features ► Network addresse
Page 308 and 309:
► HAS and CRM support clusters of
Page 310 and 311:
10.1 Configurations rules The basic
Page 312 and 313:
The PCI High nodes are supported on
Page 314 and 315:
Placement rules for frames Frame co
Page 316 and 317:
Thin Thin Thin Thin Thin Thin Thin
Page 318 and 319:
(a) (b) W ide Node W ide Node WideN
Page 320 and 321:
Mix of Additional Thin/Wide or High
Page 322 and 323:
Placement rules for switches Switch
Page 324 and 325:
► Each SP-attached server and Clu
Page 326 and 327:
Switch boards are numbered sequenti
Page 328 and 329:
SP-attached servers can connect to
Page 330 and 331:
Product Description Qty 9076-550 SP
Page 332 and 333:
170 CWS Default Entry *** 170 CWS D
Page 334 and 335:
Example 10-2 shows a sample feature
Page 336 and 337:
5765-D51 Parallel System Support Pr
Page 338 and 339:
2924 English 1 3410 CD-ROM 1 5005 P
Page 340 and 341:
2-way 9223 Node Attachment - T/P Et
Page 342 and 343:
Frame: 5 Feature: 9123 Drawer Left
Page 344 and 345:
M/T 7017 (Quantity: 2) *** M/T 7017
Page 346 and 347:
2624 32x Speed CD-ROM 1 2968 10/100
Page 348 and 349:
6159 12GB/24GB 4mm Tape Drive 1 655
Page 350 and 351:
*** M/T 7017 HARDWARE *** Product D
Page 352 and 353:
Control Workstation Attachment 4073
Page 354 and 355:
6553 SCSI Hot Swap 6-Pack 1 8131 4.
Page 356 and 357:
Example 10-5 shows a sample feature
Page 358 and 359:
3027 9.1 GB 10K RPM Ultra SCSI Disk
Page 360 and 361:
2968 10/100 Mbps Ethernet PCI 3 Ada
Page 362 and 363:
For details on these and other comm
Page 364 and 365:
The command has been enhanced to pr
Page 366 and 367:
In general, the “View or Modify P
Page 368 and 369:
If you are interested in some of th
Page 370 and 371:
If you want to add one SP-attached
Page 372 and 373:
The CWS host name. The name of the
Page 374 and 375:
CES system with existing Enterprise
Page 376 and 377:
Adding SP frames to a CES system Th
Page 378 and 379:
frame can be assigned the frame num
Page 380 and 381:
31 SP-attached servers Figure 10-20
Page 382 and 383:
► One - Complete pSeries 680 Serv
Page 384 and 385:
1st M80 2nd M80 - One - Software Pr
Page 386 and 387:
Definitions overview and naming con
Page 388 and 389:
Page 390 and 391:
SP Communication adapter requiremen
Page 392 and 393:
PCI adapter maximum quantities The
Page 394 and 395:
Notes: 1. Group restrictions apply.
Page 396 and 397:
F/C PCI Adapter Name Max. Quantity
Page 398 and 399:
► F/C 6215 must be placed in slot
Page 400 and 401:
► Maximum of one F/C 2732, 2733,
Page 402 and 403:
F/C Description Type Weighting Fact
Page 404 and 405:
► 2 Low POWER3 Thin and Wide Node
Page 406 and 407:
F/C MCA Adapter Name Number of MCA
Page 408 and 409:
Notes: 1. Not supported in 120 MHz
Page 410 and 411:
Component Feature Qty x Factor Memo
Page 412 and 413:
Component Feature Qty x Factor MCA
Page 414 and 415:
SP Legacy Models by Frame and Switc
Page 416 and 417:
SP LAN topologies The network topol
Page 418 and 419:
100 Mbps switched 10/100 Ethernet S
Page 420 and 421:
Ethernet/1 Ethernet/2 HDX 10 Mbps F
Page 422 and 423:
SP Boot/Install server requirements
Page 424 and 425:
You have to set up your SP Ethernet
Page 426 and 427:
Router Ethernet 2 Ethernet 3 Ethern
Page 428 and 429:
Disk Space required for PSSP file s
Page 430 and 431:
Image or Fileset Name Image Size Fi
Page 432 and 433:
Adding POWER3, and 332 MHz SMP Thin
Page 434 and 435:
Upgrading SMP-type nodes Available
Page 436 and 437:
Page 438 and 439:
PSSP and AIX Supported levels Since
Page 440 and 441:
Coexistence From To PSSP 2.4 and AI
Page 442 and 443:
Migration considerations Coexistenc
Page 444 and 445:
Page 446 and 447:
Parallel Environment (PE) Parallel
Page 448 and 449:
Page 450 and 451:
Network Installation Manager Networ
Page 452 and 453:
SDR is similar in concept to the AI
Page 454 and 455:
setup_server defines this as a NIM
Page 456 and 457:
Service Director Note: ► Service
Page 458 and 459:
► SD may be obtain using Internet
Page 460 and 461:
► Ensure your pSeries or RS/6000
Page 462 and 463:
http://techsupport.services.ibm.com
Page 464 and 465:
► http://techsupport.services.ibm
Page 466 and 467:
The following terms are trademarks
Page 468 and 469:
Tcl Tool command Language US User S
Page 470 and 471:
ARTIC960RxD Quad DTA, E1, 120 ohm b
Page 472 and 473:
6209 SCSI-2 F/W Differential 254 62
Page 474 and 475:
eservoir modeling 274 seismic analy
Page 476 and 477:
TPC-D 8 TURBOWAYS 100 ATM Adapter 2
Page 480:
RS/6000 SP and Clustered IBM ^ pSer
show all

Download PDF (5.2 MB) - IBM Redbooks

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?