PD86-1180 CANopen FW Manual (.pdf) - Trinamic

More documents

Recommendations

Info

TMCM-1180 / PD86-1180 CANopen Firmware Manual (V1.01 / 2011-AUG-01) 6 1 Life support policy TRINAMIC Motion Control GmbH & Co. KG does not authorize or warrant any of its products for use in life support systems, without the specific written consent of TRINAMIC Motion Control GmbH & Co. KG. Life support systems are equipment intended to support or sustain life, and whose failure to perform, when properly used in accordance with instructions provided, can be reasonably expected to result in personal injury or death. © TRINAMIC Motion Control GmbH & Co. KG 2011 Information given in this data sheet is believed to be accurate and reliable. However neither responsibility is assumed for the consequences of its use nor for any infringement of patents or other rights of third parties, which may result from its use. Specifications are subject to change without notice. Copyright © 2011, TRINAMIC Motion Control GmbH & Co. KG
TMCM-1180 / PD86-1180 CANopen Firmware Manual (V1.01 / 2011-AUG-01) 7 2 About this document This document specifies objects and modes of operation of the TRINAMIC module TMCM-1180 with CANopen firmware. As this product is a stepper motor controller and driver module the use of the CiA DSP402 protocol (described in the CiA CANopen drives and motion control device profile, Part 2) is fundamental. The CANopen firmware is designed to fulfill the DS301 version 4.02 and DS402 version 3.o standards. The CiA conformance has also been tested. As with most TRINAMIC modules the software running on the microprocessor of the TMCM-1180 consists of two parts, a boot loader and the CANopen firmware itself. Whereas the boot loader is installed during production and testing at TRINAMIC and remains – normally – untouched throughout the whole lifetime, the CANopen firmware can easily be updated by the user. It can be loaded into the module by using the firmware update function of the TMCL-IDE. It is also still possible to control the drive using TMCL commands via a special vendor-specific object (see paragraph 0). You can turn the drive back into a TMCL module by loading the TMCL firmware into the drive again. This manual assumes that the reader is already familiar with the basics of the CANopen protocol (especially DS301 and DS402). On the following pages you will find a short introduction or rather a short overview and afterwards the information will be more in detail. ABBREVIATIONS CAN Controller area network CHGND chassis ground / earth ground COB Communication object FSA Finite state automation FSM Finite state machine NMT Network management ID Identifier LSB Least significant bit MSB Most significant bit PDO Process data object PDS Power drive system RPDO Receive process data object SDO Service data object TPDO Transmit process data object EMCY Emergency object rw Read and write ro Read only hm Homing mode pp Profile position mode pv Profile velocity mode Table 2.1: Abbreviations Copyright © 2011, TRINAMIC Motion Control GmbH & Co. KG
Page 1 and 2: MECHATRONIC DRIVES WITH STEPPER MOT
Page 3 and 4: TMCM-1180 / PD86-1180 CANopen Firmw
Page 5: TMCM-1180 / PD86-1180 CANopen Firmw
Page 57 and 58:
TMCM-1180 / PD86-1180 CANopen Firmw
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77:
show all

PD86-1180 CANopen FW Manual (.pdf) - Trinamic

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?