Lighting controls

PHL-H11_INT.QXD 16-07-2004 10:42 Pagina 11.1 

Lighting controls


11.2 LIGHTING CONTROLS


Health and well being – Total cost of ownership 

The benefits of lighting controls 

Modern lighting controls deliver a range of benefits, most of which 

can be measured in real improvements to the profits of a business. 

From straightforward energy savings, through reduced maintenance 

costs to potential increases in productivity, lighting controls have 

clearly demonstrated their worth. 

Over the past 25 years Philips lighting controls have developed a full 

range of solutions designed to deliver these benefits. 

Energy Saving 

No business likes to be seen to be wasteful. Lighting controls ensure 

that lighting is only provided when and where it is needed.Advanced 

sensors are used to integrate daylight and to detect occupancy.These 

solutions have been shown to reduce lighting use by as much as 75%. 

Result-no obvious waste or compromise of comfort. 

Installation Cost Saving 

Occupancy sensors and wireless infra-red controls avoid the use of 

wired switches. Control products compatible with a ‘plug-in’ 

approach to installation can save up to 70% of the ‘on-site’ labour 

time.And these savings continue during the life of the building 

whenever changes are needed. 

Comfort 

In business today the provision of a comfortable environment for 

people to learn, work, shop, eat, rest and play is vital for success. 

With Philips’ controls, the lighting can be set to suit the task, the 

experience, individual preferences and tge required mood – and then 

readily change them as well. 

Safety 

There is an increasing awareness of safety and well being, with a 

growing emphasis on the importance of emergency lighting. 

Flexibility 

It is said that the only certainty in life is that things will change.Any 

building that cannot be readily adapted to changing business needs 

and use is not acceptable today. Philips lighting controls are designed 

to facilitate change-rapidly and effectively–whatever the application. 

Meeting Legislation 

Climate change, as well as health and safety are provoking 

governments into making more and more regulations, standards and 

legislation. Often lighting alone will not easily meet these demands 

without the addition of a control solution. In this field, Philps lighting 

controls has unrivalled knowledge and experience to share. 

Maintenance 

The easier it is to maintain a lighting installation the lower the cost 

of ownership.A Philips lighting management solution can extend lamp 

life, provide regular maintenance schedules and report on the 

condition of emergency lights. Our lighting management solutions 

ensure that exit route lighting is maintained during periods of 

occupancy and emergency lighting is effectively tested and 

monitored. 

LIGHTING CONTROLS 

11.3


Lighting controls – Key features 

E 

Automatic control 

1. Movement detection 

To control lighting within a specific area, sensing of occupancy by 

movement detection ensures that lights are activated only when 

needed. 

2. Daylight linking 

Natural light is energy-saving and beneficial to individual users. Light 

output can respond to daylight conditions, maintaining a constant level 

of indoor lighting and ensuring comfort at all times. 

3.Time schedule 

Daily programming of the management of lighting installations enables 

the correct lighting levels to be achieved at all times, by changing 

lighting levels, by switching lights on and off or by adjusting the way 

control systems respond to other devices. 

Manual control 

4. Pushbuttons/wall switches 

Lighting Control systems can also be operated manually by connecting 

conventional wall switches or pushbuttons to inputs in the lighting 

control module. 

5. Infrared remote control 

In offices and meeting rooms where the lighting requirements change 

frequently, wireless infrared control offers the flexibility to set the 

lighting, and change it at any time. 

6. PC control via IT network (TCP/IP) 

For high-level lighting management, the control system can be linked to 

a LAN. This option gives individual users’ control over their local 

working environment. 

7.Telephone handset control (via PABX) 

To enhance individual comfort, telephones can be connected to a 

lighting management system for a cost-effective way of letting users 

control their local lighting. 

Monitoring 

8. Hours run logging 

Keep track of lamp hours and produce precisely targeted relamping 

schedules and detailed departmental cost allocations. 

9. Emergency lighting test and monitor 

Lighting management systems offer a reliable way to carry out statutory 

testing of emergency and exit lighting, without interfering with the 

normal operation of standard luminaires. 

10. Current lighting status 

The ability to get a real-time view of the status of all the lights in a 

building on a floor-by-floor basis enhances effective facility management. 

11.4 LIGHTING CONTROLS 

DMX 

Lighting effects 

11. Maintained illuminance 

Set desired light levels and maintain them throughout the life of the 

lamp to achieve significant cost savings. 

12. Dimming control 

As more and more light sources can be economically dimmed, lighting 

controls need to provide both switching and dimming capabilities. 

13. Grouping of lighting circuits 

Managing a comfortably lit interior often involves one group of lights 

influencing the status of another circuit. 

14. Corridor linking 

Holding lights on in common circulation areas and corridors during all 

occupied hours is an important contribution to comfort and safety. 

15. Scene-setting 

To meet the needs of different tasks, events or moods, a selection of 

lighting scenes can be created, stored and recalled at the touch of a 

button. 

16. Control of any lighting type 

As lighting designs often require multiple types of lamps, Lighting 

Controls provide the freedom to choose any suitable lamps. 

17. Colour changing 

The ability to change the colour temperature of a lighting installation 

makes it possible to eather create a more comfortable working 

environment or introduce dynamic lighting effects in architecture. 

System connectivity 

18. Link to other building controls 

The Lighting Controls product range includes numerous possibilities for 

different building control and management systems to share information 

and functions. 

19. Full LonWorks ® Interoperability 

Achieve seamless integration into building-wide control systems by 

using a standard network protocol. 

20. Digital Adressable Lighting Interface 

The Digital Addressable Lighting Interface is the latest standard control 

interface for high-frequency electronic ballasts. With this new 

technology, control circuits are completely independent of supply 

wiring. 

21. DMX interface 

The standard protocol for the audio/visual and theatre industry. This 

interface links complex lighting scenes to presentations and displays.


Lighting controls – System selection matrix 

Philips offers a range of innovative lighting control products that 

meet the demands of many sizes and types of application.Whether 

the project is a large HQ office building, requiring a full lighting 

management system, or a small refurbishment job involving a couple 

of rooms, there is a Philips lighting control to suit the application. 

When matching your project to our lighting control products use 

the following criteria as your initial guide to product selection: 

E 

DMX 

Systems Stand alone Luminaire based 

Helio Lightmaster Scenio 100 Scenio 

Trios 

MultiDim 

Occuswitch 

Intelligent 

luminaires 

Linesense 

Automatic control page 11.15 page 11.16 page 11.27 page 11.31 

page 

11.30/11.26 

page 11.10 page 11.6 page 11.28 

Movement detection • • • • • • • • 

Daylight linking • • • • • 

Time schedule • • • 

Manual control 

Push buttons/switches • • • • • • 

Infrared remote control • • • • • • • 

PC control • • o 

Telephone control via PABX o 

Monitoring 

Hours run logging o • 

Emergency testing and logging o • 

Lighting effects 

Maintained illuminance • • • • • 

Switching and dimming • • • • • • • 

Grouping functionality • • • • 

Corridor linking • • 

Scene setting • • • • • • 

Control of any lighting type • • • • • • 

Colour changing o o • • 

System Connectivity 

• The functionality required – dimming, flexibility …. 

• The scale of the project (and hence its budget…) 

• The application – office, hotel, shop, industry, etc. 

Other factors to bear in mind include the choice of lighting design as 

well as any requirement for local user controls and/or occupancy 

response. 

Link to other building mgt. syst. • • • 

Full LonWorks ® interoperability • 

Digital Adressable Lighting Interface • • o • • • 

DMX interface • 

• standard option o project special 

LIGHTING CONTROLS 11.5


Luminaire based and basic solutions 

Philips intelligent luminaires – 

The simplest way to lighting control 

To increase comfort, energy saving and flexibility in offices, Philips has 

incorporated miniature lighting controls within the luminaires. 

Philips Lighting offers a choice of intelligent luminaire solutions that 

provide a wide range of functions such as daylight linking, movement 

detection, remote control and scene setting with energy savings of 

up to 70%. Intelligent luminaires enable lighting control to be applied 

in a building at any stage of a project.The sensor-controller 

combination within the luminaire has little impact, or none at all, on 

the electrical installation. 

Omnisense – All intelligence in one 

Primarily designed for cellular and smaller open plan offices, 

Omnisense can also be applied in other areas such as meeting 

rooms, toilets and storage rooms. By using the benefits of digital 

technology, Omnisense provides 10 pre-programmed modes to 

match a variety of applications quickly and easily. Each mode includes 

a varies parameters such as delay times and switching behaviour. In 

addition to daylight regulation and movement detection, infrared 

remote control enables users to interact with their environment: 

switch, dim or select preset lighting levels or scenes. Omnisense 

functionality can be changed easily so that its behaviour can be 

adapted to new situations. 


Occulux – Movement-dependent daylight regulation 

As a combination of a state-of-the-art light sensor and a miniature 

movement detector, Occulux regulates lighting levels depending on 

the amount of daylight entering a room and on occupation.The 

increasing need for flexibility means that lights often remain on 

unnecessarily. On the other hand, turning lights off in certain areas of 

an open plan office can create an unpleasant visual impression. 

Occulux therefore dims light down to a minimum lighting level when 

an area is unoccupied.The result is a constant, pleasant lighting level 

for office workers with a maintained adjustable minimum, enabling 

owners to benefit from considerable savings on energy costs of up 

to 50%. 

Luxsense – Daylight-dependent regulation option 

Luminaires with this option contain a unobtrusive light sensor, 

regulating light to the required level depending on the amount of 

daylight. Energy saving results from both the use of daylight and the 

compensation of the over-design effect (maintained illuminance). 

With today’s efficient lamps and optics, the compensation of the 

over-design is very effective, particularly in retrofit projects.Average 

energy savings can reach up to 35%. Luxsense is also available as a 

separate product for both TL5 and TL-D luminaires.


Occuswitch – Lighting control the easy way 

The Occuswitch is a very simple occupancy type controller that 

provides automatic switching of lighting loads of up to 10A.A built-in 

adjustable time delay allows the lights to remain on after occupancy 

for a selected period of time.An optional light sensor is also built-in 

so that if the natural daylight conditions are sufficient the lights will 

not switch on thus saving more energy. 

The Occuswitch distinguishes itself in design, quality and ease of 

installation; it is simply positioned in the middle of the room or area, 

the mains power supply wired directly to it and the luminaire circuit 

wired from it. Simplicity at its best! Occuswitch is ideally suited for 

those areas that are infrequently occupied and where dimming is not 

required - such as washrooms, stores, lobbies, corridors, cellular 

offices and meeting rooms.A version with manual IR remote 

override control is also available. 

Occuswitch 



Lighting controls Omnisense, Occulux, Luxsense 


LRI1661 

Omnisense 

- Easy selection of 10 building application modes 

with commissioning tool IRT8099 

- Mounting height: approx. 3 m 

- Default setting light level: 500 - 600 lux 

- Easy adjustment of required light level with 

commissioning tool 

- Movement detection area 20 m 2 

- Master-slave installation: up to 7 DALI luminaires 

can be slaved to 1 luminaire equipped with 

Omnisense provided they all remain in the 

movement detection area 

- Reliable Philips RC5 infrared protocol 

- Can be used with or without bracket, depending 

on luminaire type 

- Available as option for many luminaires 

LRI1340 

Occulux 

- Mounting height: approx. 3 m 


- Easy manual adjustment of minimum light level 

during absence 

- Movement detection area 20 m 2 

- Master-slave installation: up to 7 HFR luminaires 

can be slaved to 1 luminaire equipped with 

Occulux provided they all remain in the movement 

detection area 

- Can be used with or without bracket, depending 

on luminaire type 

- Available as option for many luminaires 

LRL1220 

Luxsense 

- Mounting height: 2-4 m 


- Easy manual adjustment of required light level 

IRT8099 

Commissioning tool for Omnisense luminaires. 

Easy to use and inexpensive tool to adjust light 

levels and to switch between functionality modes. 

Batteries are included. 

Product ID European Order 

Code (EOC) 

IRT8099/00 51889300 

~LIGHTM~Lightmaster


Lighting controls 



Lighting controls Occuswitch 

Product ID Weight 

European Order 

(kg) 

Code (EOC) 

LRM1050/00 SENSR MOV DET ST 0.26 51725400 

LRM1051/00 SENSR MOV DET PLUG 0.34 51732200 

LRM1060/00 SENSR MOV DET ST IR 0.26 51734600 

LRM1061/00 SENSR MOV DET PLUG IR 0.34 51736000 


Dimensions in mm 

~HELIO~Helio lighting management system 

LRM1050/00 

Movement detector with built-in lighting switch.The 

unit is designed for the automatic switching of 

lighting in indoor applications. Connection: Screw 

terminals. Switch-off delay time from 1 to 35 min. 

(selectable).The pattern of sensitivity is nearly 

circular; covering an area with a diameter of about 

7m.Mounting height 2.5 to 3 m. Daylight-override 

10 to 1000 lux (selectable), factory set at 750 lux. 

Max. switching current 10 A rms (any load). 

LRM1051/00 

Movement detector with built-in lighting switch.The 

unit is designed for the automatic switching of 

lighting in indoor applications. Connection: Wieland 

connectors GST 18-3 male/female. Switch-off delay 

time from 1 to 35 min. (selectable).The pattern of 

sensitivity is nearly circular; covering an area with a 

diameter of about 7 m. Mounting height 2.5 to 3 m. 

Daylight-override 10 to 1000 lux (selectable), factory 

set at 750 lux. Max. switching current 10 A rms (any 

load). 

LRM1060/00 

Movement detector with built-in lighting switch and an 

infrared receiver, enabling manual control 

(OVERRIDE).The unit is designed for the automatic 

switching of lighting in indoor applications. Connection: 

Screw terminals. Switch-off delay time from 1 to 

35 min. (selectable).The pattern of sensitivity is nearly 




Max. switching current 10 A rms (any load). 

LRM1061/00 

Movement detector with built-in lighting switch and 

an infrared receiver, enabling manual control 

(OVERRIDE).The unit is designed for the automatic 

switching of lighting in indoor applications. 

Connection: Wieland connectors GST 18-3 

male/female. Switch-off delay time from 1 to 35 min. 

(selectable).The pattern of sensitivity is nearly 




Max. switching current 10 A rms (any load).


Lighting controls Occuswitch 

ASSOCIATED PRODUCTS 


IRT8010/00 LRH8010/00 

IRT8050/00 



(kg) 

Code (EOC) 

LRM1064/00 SENSR ABS DET ST IR 0.26 51755100 

LRM1065/00 SENSR ABS DET PLUG IR 0.34 51757500 

IRT8010/00 TRANSM IR POINT 0.06 51749000 

LRH8010/00 MOUNT IR POINT 0.03 51797100 

IRT8050/00 TRANSM IR 2KEY WALL 0.12 51707000 

LRM1064/00 



(MANUAL SWITCH ON).The unit is designed for 

the automatic switching of lighting in indoor 

applications. Connection: Screw terminals. Switch-off 

delay time from 1 to 35 min. (selectable).The 

pattern of sensitivity is nearly circular; covering an 

area with a diameter of about 7 m. Mounting height 

2.5 to 3 m. Daylight-override 10 to 1000 lux 

(selectable), factory set at 750 lux. Max. switching 

current 10 A rms (any load). 

LRM1065/00 



(MANUAL SWITCH ON).The unit is designed for 

the automatic switching of lighting in indoor 

applications. Connection: Wieland connectors 

GST 18-3 male/female. Switch-off delay time from 

1 to 35 min. (selectable).The pattern of sensitivity is 

nearly circular; covering an area with a diameter of 

about 7 m. Mounting height 2.5 to 3 m. Daylightoverride 

10 to 1000 lux (selectable), factory set at 

750 lux. Max. switching current 10 A rms (any load). 


PHL-H11_INT.QXD 16-07-2004 10:43 Pagina 11.12


Lighting management 

The working environment 

People think and work better in a comfortable environment, which 

leads to better productivity.Today's office buildings need to be 

adaptable to the needs of both individual users and the companies 

they work for.A networked lighting management system is an 

essential part of a modern lighting installation. 

Flexibility 

Change - in a modern building this can happen every day. Philips' 

lighting management systems have been developed with change in 

mind. From the easily installed hardware to the user-friendly local 

override facilities these solutions make change much easier to deal 

with, while still delivering the individual lighting levels chosen by the 

staff. 



LightMaster 

LightMaster – Networked lighting management 

LightMaster is a family of networked lighting controls, which are very 

attractive to budget-conscious users, designers and installers. 

LightMaster components are built into a simple, yet highly flexible 

networked lighting control and monitoring system, that also offers 

simple and effective integration possibilities. 

With building use changing regularly, often within months, the 

expense of reconfiguration is now an important factor for every 

building operator.This system is specifically designed to facilitate any 

required changes in the lighting installation through the powerful yet 

easy-to-use LightManager software suite. Monitoring facilities range 

from simple status indication to sophisticated event and run-time 

logging. 

1. Intial configuration 


9-output LCM, switching 

and dimming 

Luminaire 

2. Changed configuration (lay-out)Caption 

User-friendly graphics 

LightManager is both the configuration tool and the user interface 

for LightMaster.The package is specifically designed to run under 

Microsoft Windows, ensuring that it has a familiar ‘look and feel’ to 

welcome the user. Building plans and lighting layouts are imported 

from AutoCAD or other industry-standard design packages.These 

files then become the foundation of the lighting control system’s 

supervisory software. Easily understood icons that give absolute 

clarity to the facilities management team illustrate all the lighting 

system components. 

Multi-sensor 

Wall switch


Helio 

Helio - Innovation by integration 

Helio is a lighting control system for building-wide control, which can 

become an integral part of the building management concept using 

one network. Its open system architecture, open communications 

protocol and standardised technology allow Helio to be easily 

integrated with systems supplied by different vendors such as 

heating, ventilation, window blinds, building access and more. 

2-output LCM 

8-output LCM, either switching 

only or switching and dimming 

Luminaire 

LON multi-sensor or 

conventional 

(multi-) sensor 

1. Get ready for integration 

InfraRed receiver 

Heating & ventilation 

controller 

Sunblind controller 

2. Take control with sensors, 

transmitters and pushbuttons 

Integration on all levels 

Helio is based on Echelon’s LonWorks® technology, the de facto 

standard for leading suppliers of building services controls. Plug-ins 

for other tools, such as LonMaker for Windows®, are also provided. 

As a result Helio offers numerous solutions for lighting and 

integration, driven by users’ demands for investment benefits, 

functionality and upgradeability.Three levels of lighting solutions give 

you virtually unlimited possibilities.These range from a 

basic solution for centralised lighting control, through 

a system with more advanced control functions using 

sensors, transmitters and pushbuttons, to a fully 

integrated approach to building controls. 

3. Complete integration 

with HVAC systems and sunblinds 



Lighting controls Lightmaster 



(kg) 

Code (EOC) 

LBC5000/00 SOFTW A62PC+SOFTW 4.00 53552400 

LBC5001/02 SOFTW CARD+SOFTW 0.15 53734400 

LFC5255/00 NETWK AREA CONTR 2.44 53932400 



LRH5300/50 CONTR BASE ASSY PLUG 1.26 53422000 

LLC5319/50 CONTR 9X4 PLUG SW&RE 1.71 53460200 

LLC5319/70 CONTR 9X4 PLUG SW&RE D-NO 1.00 53710800 

LLC5319/71 CONTR 9X4 PLUG SW&RE D-LIM 1.80 53762700 

LLC5359/50 CONTR 9X4 PLUG SW&RE RC5 1.71 53930000 

~LIGHTM~Lightmaster 

LBC5000/00 

Central Supervisor. IBM compatible PC with 

software and interface card, user interface to the 

LM100 system. A Central Supervisor can control up 

to 60 Area Controllers. 

Also available: 

LBC5001/02 Interface Card and LightManager 

Software to be used with a PC provided by the 

client. 

LFC5255/00 

Area Controller. A building controlled by a LM100 

system is split into a number of areas. Each area is 

supervised with an Area Controller.The Area 

Controller manages network traffic, schedules time 

commands and implements re-configuration 

commands from the Central Supervisor. 

LRH5300/50 

Base to be used with LLC5319 Lighting Control 

Modules. 

LLC5319 

Pluggable Lighting Control Module with 4 inputs and 

9 outputs (Wieland GST). Each output can be 

configured to control any light or combination of 

lights anywhere on the system. Each individual 

output is allowed to switch up to 4 A, with a 

maximum for all outputs up to 10 A divided over 

the two sides, each 5 A. Requires the LRH5300/50 

base to be mounted on. 

Versions available: 

LLC5319/50 Pluggable LCM (1-10V). 

LLC5319/70 Pluggable LCM for use with DALI 

ballasts (no feedback). 

LLC5319/71 Pluggable LCM for use with DALI 

ballasts (limited feedback). 

LLC5359/50 Pluggable LCM (1-10V) for use with 

RC5 IR remote control.






(kg) 

Code (EOC) 

LLC5314/50 CONTR 4X4 ST SW&RE 0.89 53572200 

LRH5304/50 CONTR BASE ASSY ST 2.14 53590600 

LLC5702/50 CONTR 2X2 GT SW&RE 0.36 53574600 

LLC5702/41 CONTR 2X2 GT SW&RE TIN 1.37 53412100 

LLC5702/42 CONTR 2X2 GT SW&RE 2TIN 1.72 53413800 

LLC5702/72 CONTR 16X2 GT SW&RE D 0.40 53756600 

LLC5702/73 CONTR 16X2 GT SW&RE IN 1.37 53758000 

LLC5314/50 

Lighting Control Module with screw terminals for 

4 inputs and 4 outputs (1-10 V).This unit is used to 

control circuits of lights. Each input can be 

configured to control any light or combination of 

lights anywhere on the system. Requires the 

LRH5304/50 Base to be mounted on. Dimension 

drawing includes the base (LRH5304/50). 

LRH5304/50 

Base to be used with LLC5314/50 Lighting Control 

Module. Dimension drawing includes the lighting 

control module (LCC5314/50). 

LLC5702/50 

Separate Gear Tray Lighting Control Module. Can be 

mounted inside a luminaire or switch cabinet. 

1-10V analogue dimming. 

LLC5702/72 Gear Tray Lighting Control Module, 

with single DALI output, 16 addresses and feedback, 

2 inputs. 

LLC5702 

Gear Tray Lighting Control Module with terminals 

for 2 outputs and 2 inputs in metal enclosure. Each 

input can be configured to control any light or 

combination of lights anywhere on the system. 

Versions available: 

LLC5702/41 1 Gear Tray Lighting Control Module in 

metal enclosure. 

LLC5702/42 2 Gear Tray Lighting Control Modules 

in 1 metal enclosure. 

LLC5702/73 1 Gear Tray Lighting Control Module in 

metal enclosure with one DALI output, 16 addresses 

and feedback, 2 inputs. 








(kg) 

Code (EOC) 

LLC5714/00 CONTR 0X4 DIN 0.28 53414500 

LLC5714/41 CONTR 0X4 DIN TIN 1.70 53416900 

LLC5724/50 CONTR 4X0 DIN SW&RE 0.47 53578400 

LLC5724/41 CONTR 4X0 DIN SW&RE TIN 1.84 53417600 

LLC5714/00 

Input Module for DIN Rail mounting. 

LLC5714/41 

Input Module with 4 inputs in metal enclosure. 

Allows the connection of 4 sensors or switches. 

Each sensor or switch can be configured to control 

any light or combination of lights anywhere on the 

system. 

LLC5724/50 

Output Module for DIN Rail mounting. 

LLC5724/41 

Output Module with 4 outputs in metal enclosure. 

It has screw terminals for 4 light circuits. Each of the 

outputs can be addressed individually.


Lighting controls Helio lighting management system 




(kg) 

Code (EOC) 

LRC5040/10 CONTR 1x1 ST SW&RE 0.47 51625700 



LRC5038/10 CONTR 8x4 PLUG S 1.48 53740500 


LRC5040/10 

Helio light controller with single channel for 

switching and regulating lighting loads up to 5 A, and 

providing a sensor interface for standard IR 

receivers, pushbutton interface units, movement 

detectors, and light sensors. 

LRC5042/00 

Helio light controller with two separately controlled 

outputs and one interface for standard movement, 

light and infrared sensors.The outputs are able to 

switch and regulate lighting loads up to 5 A.The 

outputs and LON bus have screw connections, the 

sensor interface is connected via RJ12 plug. 

LRC5043/00 

Helio light controller identical to the LRC5042 but 

with two sensor interfaces for standard movement 

detectors, lights sensor and IR receiver and two 

inputs for standard wall switches.The outputs have a 

6-pole screw conector that provides Live, Neutral, 

Protective Earth, Maintained live for power supply to 

batteries in emergency luminaires and a + and - for 

1- 10 V dimming. 

LRC5038/10 

Helio light controller with eight switchable outputs, 

two pairs of sensor interfaces for standard 

movement detectors, light sensors, IR receivers and 

two inputs for standard wall switches.The outputs 

are able to switch lighting loads up to 4 A.The unit 

has a maximum total rating of 10 A divided over the 

two sides, each 5 A. Each output has a 3-pole 

Wieland socket (GST) that provides Live, Neutral 

and Protective Earth. 






(kg) 

Code (EOC) 

LRC5048/00 CONTR 8x4 PLUG SW&RE 3.00 51688200 

LRI5133/10 SENSR LON MULTISENSOR 0.30 51684400 



LRC5048/00 

Helio light controller with eight separately controlled 

outputs and two interfaces for standard movement 

detectors, light sensors and pushbutton switches.The 

outputs are able to switch and regulate lighting loads 

up to 5 A.The unit has a maximum total rating of 

16 A. Each output has a 6-pole Wieland socket 

(GST) that includes a maintained live for power 

supply to batteries in emergency luminaires. Battery 

performance can then be tested by interrupting the 

maintained power supply at prescribed intervals. 

LRI5133/10 

Helio multi-sensor with movement detector, light 

sensor, and infrared receiver used for remote and 

automatic control of lighting, HVAC and sun blind 

functions in integrated room control applications.The 

IR receiver can be combined with hand-held and wall 

transmitters for remote control operations and with 

wall transmitters with built-in temperature sensors for 

automatic temperature control. Units are connected 

directly to LonWorks ® bus cable for network 

communication and power supply.Their functional 

behaviour can adapted by downloading project 

specific software over the bus. 

Mounting plate for surface mounting of LRI5133. 

This plate is packed together with the sensor itself. 

Mounting ring for recessed mounting of LRI5133. 

This ring is packed together with the sensor itself.






(kg) 

Code (EOC) 

LCU5305/00 NETWK 2x2 DIG I/O 0.20 51614100 

LCU5315/20 NETWK CLOCK 0.20 51615800 

LCN5225/00 NETWK POWER 0.60 51611000 

LCN5235/00 NETWK REPEATER 0.60 51612700 

LCU5305/00 

Helio digital I/O module providing a simple dry 

contact interface to and from various systems. 

The unit has 2 inputs and 2 outputs. 

LCU5315/20 

Helio system clock providing a real time clock and 

programmable switching schedule. 

LCN5225/00 

Helio bus power supply unit providing a voltage of 

42 V DC and a current of 1.4 A to the linkpower 

bus.The bus voltage and current is used by devices 

using LPT transceivers like Helio sensors, system 

clocks and digital I/Os. 

LCN5235/00 

Helio bus power supply/repeater regenerating bus 

communication and providing power to the bus. 






(kg) 

Code (EOC) 

LCN5245/00 NETWK ROUTER 0.60 51613400 

LCC5301/00 CABLE BUS 100M 0.01 51714800 

LCS5425/00 SOFTW UNILON CLIENT 0.10 51758200 

LCS5430/00 SOFTW UNILON SERVER 0.60 51756800 

LCS5435/00 SOFTW UNILON TRAIN 0.60 51849700 

LCS5495/00 SOFTW UNILON CREDIT - 51759900 



LCN5245/00 

Helio bus power supply/router repeater 

regenerating and managing bus communication and 

providing power to the bus. 

LCC5301/00 

Lighting control busline, used to interconnect all 

system components of the Helio lighting 

management system. 

The busline carries all data exchange between the 

various "modules" of Helio. 

The LCC5301 is a cable of 100 m without 

connectors. 

Unilon software. 

Unilon is a general configuration tool for 

LonWorks ® based systems. It offers a fully graphical 

user interface and many other features for 

commissioning of LonWorks ® systems. Each actual 

installation of one node in a network requires a 

license, so-called credit key. Unilon is now available in 

client and server version. Credits can be separately 

ordered in variable amounts.The server package 

includes documentation files about Helio and 

Unilon. 

Helio LNS Plug-ins. 

Plug-ins for other configuration tools like 

LonMaker for Windows are also available. For 

more information please contact your local Philips 

Lighting Controls representative.




PHL-H11_INT.QXD 16-07-2004 10:44 Pagina 11.24


Architecture and shops 

Versatile control range 

Scenio100 / MultiDim is a scene setting lighting control range that 

cover a wide range of applications. It provides from simple to 

comprehensive control facilities at the touch of a button.With an 

easy-to-use remote control different preset scenes can be 

programmed and selected, changing the mood of the room in 

seconds. 

Creative lighting design 

With its capacity to control a large number of channels of lighting, 

the Scenio100 / MultiDim range is ideally suited for applications using 

many different types of luminaries for incandescent, halogen and 

fluorescent lamps. In addition Scenio100 / MultiDim can also be used 

to switch on projectors, lower projection screens or close window 

blinds at just the touch of a button. 

Scene setting for all occasions 

The Scenio100 / MultiDim product range can be applied in situations 

such as conference halls, boardrooms, lecture theatres, hotel 

functions rooms, museums, showrooms, cafes, restaurants and shops. 

Caption 

Shoebaloo, Amsterdam 

Colours set the mood and add emotion 



MultiDim 

Digital control solution 

Philips DALI MultiDim offers today’s most versatile and easy-toinstall 

solution that brings the benefits of digital lighting control to 

many different application areas.Whether in shops, offices, 

conference rooms, hotels, restaurants or other applications. 

Quick and economic installation 

MultiDim consists of an integrated range of DALI-compatible devices 

that can be combined flexibly to create exactly the desired control 

functions.The systems addressable digital architecture means that 

only a single two-core cable is needed to interconnect all units.The 

possibility to eliminate conventional vertical wall wiring both reduces 

installation time and cost, and greatly increases the ease with which 

later changes can be implemented. 

MultiDim product range 


Freedom in lighting design 

MultiDim offers unbeatable freedom and ease of lighting system 

design.The MultiDim controllers can be used in combination with 

DALI-compatible fluorescent lamp ballasts and lamp interface units 

(both high voltage incandescent lamps and low voltage halogen 

lamps).Where necessary control functions can be provided by adding 

the required MultiDim units such as dimmers, control panels, IR 

remote control units and multi sensors for light levels and room 

occupancy. 

Maximising flexibility with DALI 

Thanks to the systems digital addressable control and 

communication concept, each unit in the DALI network has its own 

unique address that allows it to be switched and controlled 

independently.The systems single control line can be used to control 

different groups of lamps, and up to 63 devices connected to the 

same physical control wire can be addressed and controlled 

independently.


Scenio100 

Powerful control solution 

Scenio100 enables the lighting designer to achieve the correct 

ambience for all occasions. Either simple or advanced effects may be 

set at the touch of a button, including dynamic lighting and colour 

change as well as daylight linking and time control options. Scenes 

are created via software run on a PC, LCD touch screen or by 

infrared hand held transmitter. 

Flexibility in applications 

In retail areas time sequenced scene and colour changing is used to 

stimulate sales by highlighting products and creating an exciting 

environment. In restaurants Scenio100 provides the right atmosphere 

for a light breakfast, a working lunch or an intimate dinner. 

Other indoor applications include: museums, exhibition and 

conference centres, lecture theatres, leisure centres, stadiums, hotels, 

public buildings and prestige homes. Scenio100 is also highly effective 

in outdoor applications, particularly floodlighting. 

Choice of Dimming Racks 

Tungsten, low voltage, LED, cold cathode, fluorescent and all other 

dimmable light sources may be controlled using phase cutting, digital 

or DC voltage techniques. Dimming modules are built into compact, 

standard or custom-built racks, which are connected by a serial data 

bus to create a multi-channel control solution. Racks feature a mains 

input isolator and circuit breakers for individual output protection, as 

well as inputs for serial and DMX control, and voltage free contacts 

providing an interface to other building management systems. 

Control Interfaces 

Scenes can be controlled by LCD touch screen, infrared remote 

control and manual button control plate. Control plates with a satin 

anodised aluminium finish are standard available, with other 

decorative finishes optional available. Partition switches join and 

separate the control of rooms with demountable partitions. 

For further information about the versatile 

Scenio 100 system, please contact your local 

Philips Lighting representative. 



Industry lighting systems - Linesense 

Lighting controls in industry 

Industrial buildings today are 

models of efficiency in meeting 

their specific purpose – be it a 

logistics’ warehouse or a major 

manufacturing complex. Lighting in 

these environments plays the 

same important role as it does in 

any other work place. 

Philips industrial lighting control 

solutions are specifically intended 

to meet the exacting demands of 

these buildings to be both cost 

effective and well lit facilities. 

Lighting controls for TTX400 light-lines 

Today’s warehouses and distribution centres can be characterised by 

their large size and the few people employed. Light is switched on all 

day although the employees need it only for a limited time. For those 

applications Philips Lighting offers a stand-alone control solution, 

Linesense, to be used in combination with TTX400 light-lines. 

Linesense dims or even switches off the lights when nobody is 

present in a particular zone. 

Linesense extention with movement detector 


Easy to install 

The Linesense range comprises a supplementary 300 mm trunking 

element, containing the controller, for addition to the TTX400 light 

line.This extra unit is easily installed between the light line and the 

electrical connection unit – the “6th click” in the TTX400 system. 

High bay movement detectors and, optionally, a light sensor are 

simply connected through RJ-12 modular cables to the dedicated 

brackets. Once installed, the system works automatically and requires 

no extra maintenance. 

Energy saving 

Linesense, in combination with the highly efficient TTX400 

luminaires, decreases energy costs substantially by using presence 

detection, daylight linking and manual control. 

Examples show that energy savings up to 75% can be achieved.With 

Linesense energy savings are realised from day one, with no 

additional costs in the long run.


LON-DALI 

Digital intelligence for Light-lines 

The LON-DALI control system provides optimal lighting where it’s 

needed and when it’s needed. Promoting maximum productivity, 

comfort and safety.A system, moreover, that’s simple to operate and 

to adapt to changing industrial requirements. Providing a unique 

solution that truly reflects the needs of modern industry – today and 

into the future. 

Adaptive to needs and activities 

The LON-DALI system allows creating lighting zones within and 

across light-lines (TTX400 and Maxos). It offers total flexibility to 

control the lighting behaviour of each zone and even to reprogram 

the zones into a new lighting arrangement to accommodate changes 

in floor layout or production activity. New arrangements can be 

software configured with no need for rewiring. 

Caption 

LON-DALI system solution 

Optimal lighting 

The system, moreover, accommodates time control, manual control, 

movement detection and daylight regulation – resulting in optimal 

illumination of all tasks on the factory floor and increasing operator 

productivity, efficiency, comfort and safety. 

Taking control 

The LON-DALI controller allows for status monitoring including 

individual lamp and ballast status, burning hours and energy 

consumption in each light zone. Ensuring that the light line 

installation always functions at optimum efficiency, and allowing for 

accurate cost allocation to individual departments using the 

installation.The controller provides the means to have this 

information to be integrated into a modern Building Management 

System. 

LRC5140/41- LON-DALI light controller for industry 



Lighting controls Trios system 



(kg) 

Code (EOC) 

LRC1010/10 CONTR 1x1 ST S 0.46 51643100 


LRC1030/00 CONTR 1x1 PROG ST SW&RE 0.46 51583000 

LRC1015/10 CONTR 1x1 DIN S 0.33 51644800 

LRC1025/10 CONTR 1x1 DIN SW&RE 0.33 51646200 

LRC1035/00 CONTR 1x1 PROG DIN SW&RE 0.33 51586100 




LRC1010/10 

LRC1020/10 

LRC1030/00 

Trios multifunctional and addressable light controllers 

in a housing for distributed installation in three 

versions.The switching (LRC1010) and the 

switching/regulating (LRC1020) versions have 

pre-defined functionalities that depend on the 

connection of movement detector, infrared receiver 

and/or light sensor.They are specifically designed for 

energy saving solutions with dimmable and 

non-dimmable luminaires.The functionality of the 

switching and regulating LRC1030 can be adapted 

by PC programming software (available separately) 

for special lighting control applications. A highly 

informative Trios Manual is available to assist 

designers and installers in selecting the correct 

products for their applications. 

LRC1015/10 

LRC1025/10 

LRC1035/00 

Trios multifunctional and addressable light controllers 

in a DIN-rail housing for centralised installation in 

three versions.The switching (LRC1015) and the 

switching/regulating (LRC1025) versions have 

pre-defined functionalities that depend on the 

connection of a movement detector, infrared 

receiver and/or light sensor.They are specifically 

designed for energy saving solutions with dimmable 

and non-dimmable luminaires.The functionality of 

the switching and regulating LRC1035 can be 

adapted by PC programming software (available 

separately) for special lighting control applications. 

A highly informative Trios Manual is available to assist 

designers and installers in selecting the correct 

products for their applications. 

LCS1030/00 

Trios Software 

Software for use on a PC to alter the parameters of 

the LRC1030/1035 controllers. 

Trios Handbook 

Trios Handbook, intended to assist consultants, 

engineers, installers and other professionals involved 

in project management and design, and in specifying 

and procuring lighting control systems. Its purpose is 

to aid the reader in selecting the most effective 

lighting solution for a particular application 

requirement. It describes the fundamental 

technicalities of the Trios system and its associated 

components, and gives detailed information on 

installation, test and commissioning. 

More information: www.controls4lighting.com


Lighting controls Scenio system 



(kg) 


Code (EOC) 

LRC1555/00 CONTR 1X1 0.35 51653000 

LRC1505/00 CONTR 1X0 EXTENSION 0.35 51651600 

IRT8020/00 TRANSM IR SCENIO 0.22 51761200 

~TRIOS~Trios system 

LRC1555/00 

Scenio light controller with two modular sockets: 

one dedicated for sensors (IR receivers and/or 

movement detectors) and the other for businterconnection 

to the extension modules LRC1505. 

Up to three IR receivers and three movement 

detectors can be connected to the sensor input. 

The unit has one output channel suitable to switch a 

maximum load of 1150 VA, and a 1-10 V DC 

regulation output. 

LRC1505/00 

Scenio extension module to be linked to the light 

controller LRC1555 via a communication bus line. It 

has two modular sockets, both intended for bus 

loop-through connections. Sensors (IR receivers, 

movement detectors) cannot be connected to this 

unit.The unit has one output channel suitable to 

switch a maximum load of 1150 VA, and a 1-10 V 

DC regulating output. A 20 cm busline 

interconnection cable is supplied with the unit. 

IRT8020/00 

Eight-preset hand-held transmitter, suitable for 

infrared control of Scenio applications. It has 4 keys 

for presets and one key for “all off”. Keys for 

individual control and preset programming are 

located under a hinged cover at the bottom of the 

transmitter. In “teach mode” the transmitter can be 

used as a commissioning tool for Scenio.The group 

address selector switch is contained in the battery 

compartment.The unit is supplied complete with 

wall holder and batteries. 



Lighting controls General purpose components 





(kg) 

Code (EOC) 

IRT8010/00 TRANSM IR POINT 0.06 51749000 

LRH8010/00 MOUNT IR POINT 0.03 51797100 

IRT8050/00 TRANSM IR 2KEY WALL 0.12 51707000 

IRT8030/00 TRANSM IR TRIOS 0.22 51763600 

~GENERAL~General purpose components 

IRT8010/00 

Hand-held two-key transmitter, for infrared control of 

various lighting control systems.This transmitter was 

developed for the Occuswitch “presence” and 

“absence”, but it can also be used with Trios and 

other systems.The Occuswitch-IR is only able to 

switch, but when the transmitter is used with the 

named systems it can also dim the lights (by pressing 

a button >0.5 sec).The group address selector switch 

is contained in the battery compartment.The unit is 

supplied with batteries. A wall holder is available. 

LRH8010/00 

Wall holder for the IRT8010 hand-held two-key 

transmitter. 

IRT8050/00 

Two-key infrared remote control transmitter for wall 

mounting and table-top use.The unit can be used in 

Trios applications.The actual function of the two 

large keys can be selected with a dip switch in the 

battery compartment. A dip switch is also used to 

select the group address. 

IRT8030/00 

Four-preset hand-held transmitter, suitable for 

infrared control of Trios applications. It has 4 keys for 

presets and one key for “all off”. Keys for individual 

control and preset programming are located under a 

hinged cover at the bottom of the transmitter. In 

“teach mode” the transmitter can be used as 

commissioning tool for Trios.The group address 

selector switch is contained in the battery 


wall holder and batteries.





(kg) 


Code (EOC) 

IRT8040/00 TRANSM IR SYS 0.22 51765000 

IRT8080/00 TRANSM IR MULTI-FUNC 0.22 51767400 

IRT8055/00 TRANSM IR 2KEY WALL TEMP 0.12 51843500 

IRT8040/00 

Hand-held transmitter, suitable for infrared control of 

Helio applications combined with HVAC and 

Sunblind systems. It has keys for two lighting groups, 

blinds control and temperature control and a key for 

“all off/absence”. Keys for lighting presets and preset 

programming are located under a hinged cover at 

the bottom of the transmitter.The group address 



wall holder and batteries. 

IRT8080/00 

Hand-held transmitter, suitable for infrared control of 

various lighting control systems, other building 

systems (sunblind, HVAC).The transmitter can easily 

be adapted to project specifications by selecting one 

of its 15 settings.This can be achieved without any 

tools, and even after installation.The group address 



text plates for the various settings, wall holder and 

batteries. 

IRT8055/00 

Multi-purpose infrared remote control transmitter 

for wall mounting, suitable for the transmission of 

measured temperature values.The unit can be used 

in integrated control systems with Heating, 

Ventilation and Airconditioning (HVAC) in 

combination with Helio applications.The actual 

function of the two large keys can be selected with 

a switch in the battery compartment.The same 

switch is used to select the group address. Only 

available as project special. 







(kg) 


Code (EOC) 

LRM8114/00 SENSOR MOV DET 0.07 51906700 

LRI8134/00 SENSOR MULTISENSOR 0.07 51904300 

LRM8115/00 SENSR MOV DET LONG 0.07 51722300 

LRM8116/00 SENSR MOV DET WIDE 0.07 51841100 

LRM8114/00 

Compact advanced movement detector that 

features variable delay-to-off via DIP switch and can 

be part shaded to limit coverage.The sensor is 

powered via the additional modular plug-in (RJ12) 

connector cable that attaches it to a lighting 

controller.The sensor is suitable for both recessed 

and surface mounting. Mounting height is between 

2.5 m and 3.5 m. 

LRI8134/00 

Compact multi-sensor combining advanced internal 

light sensor, movement detector and infra-red 

receiver.The unit features individual element 

selection, variable delay-to-off via DIP switch and 

auto-calibrating light sensor. Movement detector can 

be part shaded to limit coverage.The sensor is 

powered via the additional modular plug-in (RJ12) 

connector cable that attaches it to a lighting 

controller.The sensor is suitable for both recessed 

and surface mounting. Mounting height is between 

2.5 m and 3.5 m. 

LRM8115/00 

Wall-mounted passive infrared movement detector 

for energy saving solutions in indoor lighting 

applications (automatic light switching based on 

occupancy). It detects the slightest movement within 

a range 25 m long. Equipped with adjustable 

switchoff delay times up to 35 minutes. Electrical 

connections via an additional sensor cable with a 

modular socket (“snap-in”).The daylight override 

function prevents the lights being witched on, if 

enough daylight is available. 

LRM8116/00 

Wall-mounted passive infrared movement detector 

for energy saving solutions in indoor lighting 

applications (automatic light switching based on 

occupancy). It detects the slightest movement within 

an angle of 90º (maximum range 15 m by 15 m at a 

mounting height of 2.1 m). Equipped with adjustable 

switchoff delay times up to 35 minutes. Electrical 

connections via an additional sensor cable with a 

modular socket (“snap-in”).The daylight override 

function prevents the lights being switched on, if 

enough daylight is available.



Product ID 


Weight 

(kg) 


Code (EOC) 

IRR8125/00 SENSR IR NV 0.03 51716200 

LRD8000/00 DIMMER 1KVA MAGNETIC TX 0.40 51571700 

LRD8010/10 DIMMER 1KVA ELECTRONIC TX 0.53 51573100 

LCU8020/00 INTERF PUSHBUTTON 0.10 51656100 

IRR8125/00 

Infrared receiver for remote control of lighting 

systems and other building-related functions.The unit 

is especially intended for “invisible” mounting behind 

a false ceiling. Only a thin plastic optic protrudes 

from the ceiling. More infrared receivers can be 

connected in parallel to cover large or odd-shaped 

rooms. It is powered from the corresponding 

controller, not requiring an external power supply 

unit. Electrical connections with a fixed cable (1 m.) 

with modular plug. Mounting height 2.5 to 3 m. 

LRD8000/00 

Light regulator for incandescent lamps, high-voltage 

halogen lamps and low-voltage halogen lamps with 

conventional transformers.The minimum light output 

level can be adjusted between 1% and 10% of 

maximum light output level. A green “power on” 

LED indicates the power status of the unit. Max. load 

is 1000 VA. 

LRD8010/10 

Light regulator for incandescent lamps, high-voltage 

halogen lamps and low-voltage halogen lamps with 

electronic transformers.The minimum light output 

level can be selected between 1% and 10% of 

maximum light output level. A green “power on” 

LED indicates the power status of the unit. Max. load 

is 1000 VA. 

LCU8020/00 

Push-button interface. RC5 code generator with 

digital inputs for the connection of push-buttons. 

Intended for manual control of light controllers and 

for coupling to other systems such a building 

management systems.The unit is connected to the 

infrared remote control input of the controller. 

Combination with an IR receiver is possible. Codes 

generated, depend on the input terminals used, 

20 combinations are possible. Different sets of 

codes, for Helio/Trios and Scenio can be selected 

with a rotary switch.The unit is powered from the 

corresponding controller. 








(kg) 

Code (EOC) 

LPS100/00 POTSW 1-10V DIM 0.14 55803900 

LPS100/01 POTSW 1-10V DIM 0.14 55806000 

LCC8024/00 CONN BLOCK RJ12 1M-3F 0.01 51599100 

LPS100/00 

Manual rotary potentiometer with microswitch for 

recessed mounting. In combination with one or 

more electronic HF lightregulating ballasts, electronic 

light regulators or Trios controllers, it serves to 

control the light level of fluorescent lamps, halogen 

lamps or incandescent lamps. 

LPS100/01 

Manual rotary potentiometer with microswitch for 

surface mounting. In combination with one or more 

electronic HF light-regulating ballasts, electronic light 

regulators or Trios controllers, it serves to control 

the light level of fluorescent lamps, halogen lamps or 

incandescent lamps. 

LCC8024/00 

Branching connector with three modular sockets 

and one modular plug for use when more sensors 

are to be connected to the same controller input 

socket. (Or extension cable socket).





(kg) 


Code (EOC) 

LCC8014/00 CABLE SENSR RJ12M-RJ12M 5M 0.12 51637000 

LCC8012/00 CABLE EXT RJ12M-RJ12F 5M 0.13 51595300 

LCC8013/00 CABLE EXT RJ12M-RJ12F 20M 0.50 51597700 

LCC8011/00 CABLE INTER RJ12M-RJ12M 1M 0.03 51593900 

LCC8015/00 CABLE IR RJ12M-RJ12M 5M 0.12 51711700 

LCC8016/00 CABLE RJ12-END 3M 0.06 53920100 

LCC8016/10 CABLE RJ12-BL4 3M 0.06 53922500 

LCC8014/00 

Cable of 5 m length with modular plugs at both 

ends for the connection of sensors to the various 

types of light controllers. 

LCC8012/00/LCC8013/00 

Extension cables of 5 m length (LCC8012) and 

20 m length (LCC8013) with modular plugs and 

sockets to increase the distance between sensors 

(infrared receivers, light sensors and movement 

detectors) and the corresponding controllers. 

Product ID A 

LCC8012/00 5000 

LCC8013/00 20000 

LCC8011/00 

Interlink cable of 1 m length with modular plugs at 

both ends for interconnection of multifunctional light 

controllers so that the connected sensors can be 

shared by more controllers. 

LCC8015/00 

Interlink cable of 5 m length with modular plugs on 

both ends for interconnection of Trios light 

controllers.The cable is intended to distribute (only) 

the RC5 signal from a push-button interface over 

the connected controllers, especially in centrally 

controlled Trios applications. 

LCC8016/00 

LCC8016/10 

Sensor link cable of 3 m length with RJ12 connector 

on one end. Intended to connect general purpose 

sensors (excl. IRR8125) to LightMaster systems. 

The /00 is free end and /10 has a BL4 connector. 




11.38 LIGHTING CONTROLS

Lighting controls

Create successful ePaper yourself

Delete template?

Save as template?