Exclusive U.S. Distributor - Apollo Design Technology

More documents

Recommendations

Info

Operation Modes The Multispot HP3-90 has several operating modes to allow for local preset control and remote operation. “ST” Static Color Mode Press the MODE button (1) until the first two digits on the display shows “ST”. Choose a color, “ST 0” – “ST25”, by pressing the left/right buttons (2 or 3), see table below. The +/- buttons (4 or 5) change the dimming level, “L 0” – “L100”. Pressing the +/- buttons (4 or 5) once shows the current dimming level. The dimming level can then be changed by using the +/- buttons (4 or 5). Holding the +/- buttons (4 or 5) for longer than 1 second accelerates the change rate of the displayed value to 3 times normal speed. The display will automatically return to show “ST##” after 5 seconds, and the dimming level will remain as set. # Color # Color ST 0 All Off ST13 Flesh ST 1 Red ST14 Light Blue Green ST 2 Green ST15 Light Green ST 3 Blue ST16 Light Purple ST 4 Yellow ST17 Light Lavender ST 5 Pink ST18 Light Blue ST 6 Turquoise ST19 White 1 (cool) ST 7 Lime ST20 White 2 ST 8 Orange ST21 White 3 ST 9 Marine ST22 White 4 ST10 Blue Green ST23 White 5 (warm) ST11 Lavender ST24 Light Orange ST12 Hot Pink ST25 Dark Orange NOTE: This mode is automatically disabled when an external DMX signal is present. “C” Color Picker Mode Press the MODE button (1) until the first digit on the display shows “C”. There are 226 color steps. Choose a color, “C 0” – “C225”, by pressing the left/right buttons (2 or 3). The +/- buttons (4 or 5) change the dimming level, “L 0” – “L100”. Pressing the +/- buttons (4 or 5) once shows the current dimming level. The dimming level can then be changed by using the +/- buttons (4 or 5). Holding the +/- buttons (4 or 5) for longer than 1 second accelerates the change rate of the displayed value to 3 times normal speed. The display will automatically return to show “C###” after 5 seconds, and the dimming level will remain as set. NOTE: This mode is automatically disabled when an external DMX signal is present. 15
<strong>Exclusive</strong> U.S. <strong>Distributor</strong> “SP” Switch / Strobe Patterns Mode In this mode you will only find hard switching and strobe patterns. Press the MODE button (1) until the first two digits on the display shows “SP”. Choose a pattern, “SP 0” – “SP12”, by pressing the left/right buttons (2 or 3), see table below. # Pattern # Pattern SP 0 Red - Green SP 7 Red - Green - Blue SP 1 Green - Blue SP 8 Red - Yellow - Green - Turquoise - Blue - Hot Pink SP 2 Red - Blue SP 9 Strobe Red SP 3 Red - Yellow SP10 Strobe Green SP 4 Hot Pink - Lime SP11 Strobe Blue SP 5 Pink - Blue SP12 Strobe White SP 6 Turquoise - Pink The +/- buttons (4 or 5) change the color speed or activate the Sound-to-Light function, “SL 0” – “SL25”, “S2L” . Pressing the +/- buttons (4 or 5) once shows the current setting. The setting can then be changed by using the +/- buttons (4 or 5), see table below. The display will automatically return to show “SP##” after 5 seconds, and the speed setting will remain as set. Setting Speed Setting Speed S2L Sound-to-Light SL13 1 step per second SL 1 1 step per 240 seconds SL14 1.5 steps per second SL 2 1 step per 120 seconds SL15 2 steps per second SL 3 1 step per 90 seconds SL16 2.5 steps per second SL 4 1 step per 60 seconds SL17 3 steps per second SL 5 1 step per 30 seconds SL18 4 steps per second SL 6 1 step per 20 seconds SL19 5 steps per second SL 7 1 step per 10 seconds SL20 6 steps per second SL 8 1 step per 5 seconds SL21 7 steps per second SL 9 1 step per 3 seconds SL22 8 steps per second SL10 1 step per 2 seconds SL23 9 steps per second SL11 1 step per 1.6 seconds SL24 10 steps per second SL12 1 step per 1.2 seconds SL25 11 steps per second Please note that above speed levels are only applicable to patterns “SP 0” – “SP 8”. When using patterns “SP 9” – “SP12”, “S2L “ indicates Sound-to-Strobe and “SL 1” – “SL25” are strobe speed ranging from 1Hz to 18Hz. When Sound-to-Light or Sound-to-Strobe, “S2L “, is selected, the “S” indicator (6) will be illuminated. The built-in microphone will be active. NOTE: This mode is automatically disabled when an external DMX signal is present. 16
Page 1 and 2: Exclusive U.S. Distributor
Page 3 and 4: Exclusive U.S. Distributor Introduc
Page 5 and 6: Exclusive U.S. Distributor 3. Disco
Page 7 and 8: Exclusive U.S. Distributor Getting
Page 9 and 10: Exclusive U.S. Distributor 7. Pull
Page 15: Exclusive U.S. Distributor NOTE: Th
Page 19 and 20: DMX channel 1 Exclusive U.S. Distri
Page 21 and 22: Exclusive U.S. Distributor “EDIT
Page 23 and 24: Exclusive U.S. Distributor Standard

Exclusive U.S. Distributor - Apollo Design Technology

Create successful ePaper yourself

Delete template?

Save as template?