European Technical Approval ETA-06/0157 - ETA-Danmark
European Technical Approval ETA-06/0157 - ETA-Danmark
European Technical Approval ETA-06/0157 - ETA-Danmark
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Page 4 of 23 of <strong>European</strong> <strong>Technical</strong> <strong>Approval</strong> no. <strong>ETA</strong>-<strong>06</strong>/<strong>0157</strong><br />
Perforated Profiled metal decking substrate (acoustic)<br />
• screw IFP2 6.7xL + plate IRP 82x40 (manufacturer SFS INTEC)<br />
• screw TPR 6.3xL + IRD 82x40 (manufacturer SFS INTEC)<br />
• screw FASTOVIS 3036 TF DF + plate 82x40R DF (manufacturer LR <strong>ETA</strong>NCO)<br />
• rivet PER/RER + 82x40R DF (manufacturer LR <strong>ETA</strong>NCO)<br />
Concrete substrate<br />
• screw TI 6.3xL + plate IRD 82x40 (manufacturer SFS INTEC)<br />
• nail DT 6.3xL + plate IRD 82x40 (manufacturer SFS INTEC)<br />
• screw TI 6.3xL + plate IF/IG C 82x40 (manufacturer SFS INTEC)<br />
• screw BETOFAST TH 3C + plate 82x40R (manufacturer <strong>ETA</strong>NCO)<br />
• screw BETOFAST TH DF 3C + plate 82x40R (manufacturer <strong>ETA</strong>NCO)<br />
• screw BETOFAST TT 2C + plastic sleeve <strong>ETA</strong>NCOPLAST T80x40 (manufacturer <strong>ETA</strong>NCO)<br />
• nail NAILFIX CH + plate 82x40 R SC (manufacturer LR <strong>ETA</strong>NCO)<br />
Lightweight concrete substrate<br />
• screw IGR S 8.0xL + plate IG8 C 82x40 (manufacturer SFS INTEC)<br />
• screw MULTIFAST TB INOX A2 + 80x40R (manufacturer LR <strong>ETA</strong>NCO)<br />
Wood substrate<br />
• screw IG 6.0xL + plate IRD 82x40 (manufacturer SFS INTEC)<br />
• screw IWT 5.0xL + plate IRC/W 82x40 (manufacturer SFS INTEC)<br />
• screw EVF2C 4.8xL + plate 82x40R SC (manufacturer LR <strong>ETA</strong>NCO)<br />
• screw EVDF2C 4.8xL + plate 82x40R DF (manufacturer LR <strong>ETA</strong>NCO)<br />
• screw EVDF 2C 4.8xL + plate 82x40R SC (manufacturer LR <strong>ETA</strong>NCO)<br />
• screw MULTIFAST TF + plate 80x40R (manufacturer LR <strong>ETA</strong>NCO)<br />
All the fasteners conform to the specifications of the <strong>ETA</strong>G 0<strong>06</strong>(see Note).<br />
The flexible membranes and the fasteners are commercialised in separate transactions and assembled on site.<br />
The means of fastening are presented in annex 4.<br />
The insulation material is fastened in the centre of each insulation panel with fasteners. The number of fasteners<br />
or fasteners and the type are defined in the National Regulations and /or product certificates for the insulation<br />
materials.<br />
Note In addition to the list of fasteners, other fasteners may also be used unless they are covered by a valid<br />
<strong>ETA</strong> and with rectangular plate with dimensions of 82 × 40 (as example, the fasteners of the <strong>ETA</strong> 08/0285 from<br />
AFAST BV – Guardian Fastening System- with plate size 82 × 40)<br />
Insulation<br />
The wind uplift test has been performed on a mineral wool substrate with compressibility at 10% of 50 kPa and<br />
point load behaviour of 120 kPa, deformation 5 mm, and the values are valid for other insulation materials with<br />
the same thickness (0 mm – 350 mm) and equal or higher compressibility and point load behaviour. The<br />
insulation material is not part of the kit. The use of the insulation board as substrate for mechanically fastened<br />
roof waterproofing is defined in national provisions.<br />
Intended use<br />
DERBIGUM SP 4 FR and DERBICOLOR 4 WSL single layer roof waterproofing kit is used for waterproof covering<br />
for sloped or flat roofs. The kits are specially designed for mechanical fastening.<br />
The load bearing elements are made from steel, concrete, lightweight concrete or wood. The MEFAWAME can be<br />
installed directly on the substrate or on an insulation material. In the latter case the insulation material shall comply<br />
with the requirements mentioned above.