ETA 060158 IMPERBEL Double layer UK renew Final - ETA-Danmark

More documents

Recommendations

Info

I LEGAL BASIS AND GENERAL CONDITIONS Page 2 of 21 of European Technical Approval no. ETA-06/0158 1 This European Technical Approval is issued by ETA-Danmark A/S in accordance with: - Council Directive 89/106/EEC of 21 December 1988 on the approximation of laws, regulations and administrative provisions of Member States relating to construction products 1) , as amended by Council Directive 93/68/EEC of 22 July 1993 2) . - Bekendtgørelse 559 af 27-06-1994 (afløser bekendtgørelse 480 af 25-06-1991) om ikrafttræden af EF direktiv af 21. december 1988 om indbyrdes tilnærmelse af medlemsstaternes love og administrative bestemmelser om byggevarer. - Common Procedural Rules for Requesting, Preparing and the Granting of European Technical Approvals set out in the Annex to Commission Decision 94/23/EC 3) . - Guideline for European Technical Approval of Mechanically fastened roof-waterproofing kits, ETA-Guideline N o 006, Edition March 2000. 2 ETA-Danmark A/S is authorized to check whether the provisions of this European Technical Approval are met. Checking may take place in the manufacturing plant. Nevertheless, the responsibility for the conformity of the products to the European Technical Approval and for their fitness for the intended use remains with the holder of the European Technical Approval. 3 This European Technical Approval is not to be transferred to manufacturers or agents of manufacturers other than those indicated on page 1, or manufacturing plants other than those indicated on page 1 of this European Technical Approval. 4 This European Technical Approval may be withdrawn by ETA-Danmark A/S pursuant to Article 5(1) of Council Directive89/106/EEC. 1) Official Journal of the European Communities N o L40, 11 Feb 1989, p 12. 2) Official Journal of the European Communities N o L220, 30 Aug 1993, p 1. 3) Official Journal of the European Communities N o L 17, 20 Jan 1994, p 34. 5 Reproduction of this European Technical Approval including transmission by electronic means shall be in full. However, partial reproduction can be made with the written consent of ETA-Danmark A/S. In this case partial reproduction has to be designated as such. Texts and drawings of advertising brochures shall not contradict or misuse the European Technical Approval. 6 This European Technical Approval is issued by ETA-Danmark A/S in Danish. This version corresponds fully to the version circulated within EOTA. Translations into other languages have to be designated as such.
Page 3 of 21 of European Technical Approval no. ETA-06/0158 II SPECIAL CONDITIONS OF THE EUROPEAN TECHNICAL APPROVAL 1 Definition of product and intended use General DERBIGUM SP 3 FR on DERBICOAT HP 2,5 and DERBICOLOR 4 FR on DERBICOAT HP 2,5 double layer roof waterproofing kits consists of two membranes, which are glued together with a cold adhesive and the under layer is mechanically fastened to the substrate. The membranes are placed on a mineral wool insulation board, which is also mechanically fastened to the substrate. The mineral wool boards are not part of the kit. Membranes DERBIGUM SP 3 FR is a membrane made from polymer modified bitumen (APP) with a double-layer reinforcement in the top layer of the membrane of approx. 150 g/m 2 non-woven polyester felt and 55 g/m 2 fibreglass. DERBIGUM SP 3 FR has a total thickness of 3 mm and a weight of 3,1 kg/m 2 . Standard width is 1,10 m. DERBICOLOR 4 FR is a membrane made from polymer modified bitumen (APP) with reinforcement complex in the middle layer of the membrane of approx. 185 g/m 2 non-woven polyester felt and fibreglass. DERBICOLOR 4 FR has a total thickness of 4 mm and a weight of 5,3 kg/m 2 . Standard width is 1,10 m. DERBICOAT HP 2,5 is a membrane made from polymer-modified bitumen (APP) with reinforcement complex in the middle layer of the membrane of approx. 100 g/m 2 non-woven polyester felt and fibreglass. DERBICOAT HP 2,5 has a total thickness of 2,5 mm and a weight of 2,9 kg/m 2 . Standard width is 1,10 m. The membranes are supplied in roll form. The different membranes and fasteners which can compose the mechanically fastened flexible roof waterproofing membrane kit (in the following referred to as MEFAWAME) and their properties are presented in Annexes 1 and 2. The holder of the ETA is fundamentally responsible of the MEFAWAME. The flexible membranes which constitute the MEFAWAME are exclusively distributed by Imperbel S.A., subsidiary companies and distributors Fasteners The different fasteners, manufactured by different manufacturers (SFS INTEC or LR ETANCO), depend on the substrate: Profiled metal decking substrate (standard) • screw IR2 4.8xL + plate IR 82x40 (manufacturer SFS INTEC) • screw IR2S 4.8xL + plate IR 82x40 (manufacturer SFS INTEC) • screw EHBDF2C 4.8xL + plate 82x40R DF (manufacturer LR ETANCO) • screw EVDF2C 4.8xL + plate 82x40R DF (manufacturer LR ETANCO) • screw EVDF2C 4.8xL + plate 82x40R SC (manufacturer LR ETANCO) • screw VMS2C 4.8xL + plate 82x40R DF (manufacturer LR ETANCO) • screw EVF2C 4.8xL + plate 82x40 R DF (manufacturer LR ETANCO) • screw EVF2C 4.8xL + plate 82x40R SC (manufacturer LR ETANCO) • screw ISODRILL TT + plate Etancoplast T80x40 (manufacturer LR ETANCO) • screw EGB2C 4.8XL + plate Etancoplast T80x40 (manufacturer LR ETANCO) • screw ISODRILL TT + plate 82x40R DF (manufacturer LR ETANCO) • screw ISODRILL TH DF + plate 82x40R DF (manufacturer LR ETANCO)
Page 1: ETA-Danmark A/S Kollegievej 6 DK-29
Page 5 and 6: mechanical fastening. Page 5 of 21
Page 7 and 8: Page 7 of 21 of European Technical
Page 11 and 12: Type ETAG Paragraph IR2 4,8 × L +
Page 13 and 14: Material properties of the screws a
Page 19 and 20: Laying and overlaps of the second l
Page 21: Page 21 of 21 of European Technical

ETA 060158 IMPERBEL Double layer UK renew Final - ETA-Danmark

Create successful ePaper yourself

Delete template?

Save as template?