Autovue 17.1 - Oracle Software Downloads

More documents

Recommendations

Info

FullColorPrinterSupport Enable color printing for some monochrome images. Set to 0: Default AutoVue behavior; where some transparent monochrome images are not printed in color due to some printers that do not fully support transparency. Set to 1: Enables certain monochrome images to be printed in color with color printers. This flag should not be set by default because it has some drawbacks and may cause some problems on some printers. Enabling option 1 could cause a decrease in performance: • The spool size is much larger because there is 8 to 23 times more information sent to the printer. • Not all printers support image transparency and using them with this option may yield incorrect results. Syntax: [Options] FullColorPrinterSupport = GpsOutText Set to 1: When you run outtext.exe, it only reports the first level of Xrefs in the hierarchy with the fully resolved/qualified path to the Xrefs. Set to 0: When you run outtext.exe, all Xref instances are reported and the path to the Xrefs is not fully qualified. Syntax: [Options] GpsOutText = IGESLoadDraftFirst Set to 1 to display the 2D page first, display of the 3D page as a 2D projection of the 3D model, in IGES files. Syntax: [Options] IGESLoadDraftFirst = Release Notes - AutoVue Desktop Edition - 8 - July 18, 2007 0 0 0
J2KRESOLUTION Added two new possible values for this option. Setting to +num gives the same result as DYNAMIC but increases the resolution by a factor of num where num is a value from 1 to 100 (up to the maximum possible resolution of the image). Setting to –num gives the same result as DYNAMIC but decreases the resolution by a factor of num where num is a value from 1 to 100 (down to the lowest possible resolution of the image). Syntax: [Options] J2KRESOLUTION = [DYNAMIC | HIGH | MEDIUM | LOW | +num | -num ] LWDEFAULT Set the default line weight. Specify a value between 1 (which corresponds to 0.01mm) and 100 (which corresponds to 1mm). Default value is 25 (which corresponds to 0.25mm). Syntax: [Options] LWDEFAULT = [1-100] MESHBUILDTOPOLOGY Set to 0 if you do not want to build the topology in mesh mode. Applies to the following file formats: • Catia 5 • Pro/ENGINEER • SolidWorks • Unigraphics • STL Note: This option replaces the following INI options: SWBUILDMESHTOPOLOGY, Catia5MeshBuildTopology and BUILDMESHTOPOLOGY. Syntax: [Options] MESHBUILDTOPOLOGY = NOSYMBOLTTF Set to 1 to override the Charset of Symbol fonts. It will be replaced by the default Charset. This option applies to DWF and DWG files only. Syntax: [Options] NOSYMBOLTTF = DYNAM IC Release Notes - AutoVue Desktop Edition - 9 - July 18, 2007 25 1 0
Page 1 and 2: Release Notes: Desktop Edition Auto
Page 3 and 4: EDA Formats • Added support for C
Page 5 and 6: • Added support for Multipage Net
Page 7: CATIA5BuildCGMSets Controls the dis
Page 11 and 12: [ECAD] Options should be specified
Page 13 and 14: [Print Options] Options should be s
Page 15 and 16: CatiaV4.fontmap. The fontmap file i
Page 17 and 18: New INI File Settings [Options] Par
Page 19 and 20: NCD_NUMDECIMALS Option applies to N
Page 21 and 22: • Added support for Parasolids ve
Page 23 and 24: Default: 0 DWFRGBCOLOR= Option appl
Page 25 and 26: AutoVue 18: June 30, 2004 3D Functi
Page 27 and 28: • Added off-line DMS support thro
Page 29 and 30: AutoVue 17.1: June 01, 2003 Format
Page 31: AutoVue 17: December 09, 2002 Forma

Autovue 17.1 - Oracle Software Downloads

Create successful ePaper yourself

Delete template?

Save as template?