8.3.3.8 - Force10 Networks

More documents

Recommendations

Info

www.dell.com | support.dell.com 18 | TACACS+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .659 Configuration Task List for TACACS+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .659 TACACS+ Remote Authentication and Authorization . . . . . . . . . . . . . . . . . . . . . . .661 Command Authorization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .663 Protection from TCP Tiny and Overlapping Fragment Attacks . . . . . . . . . . . . . . . . . . .663 SCP and SSH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .663 Using SCP with SSH to copy a software image . . . . . . . . . . . . . . . . . . . . . . . . . . .665 Secure Shell Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .666 Troubleshooting SSH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .669 Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .669 Trace Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .670 Configuration Tasks for Trace Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .670 VTY Line and Access-Class Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .676 VTY Line Local Authentication and Authorization . . . . . . . . . . . . . . . . . . . . . . . . . .676 VTY Line Remote Authentication and Authorization . . . . . . . . . . . . . . . . . . . . . . . .677 VTY MAC-SA Filter Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .677 36 Service Provider Bridging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 679 VLAN Stacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .679 Important Points to Remember . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .680 Configure VLAN Stacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .680 Create Access and Trunk Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .681 Enable VLAN-Stacking for a VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .681 Configure the Protocol Type Value for the Outer VLAN Tag . . . . . . . . . . . . . . . . . .682 FTOS Options for Trunk Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .683 Debug VLAN Stacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .684 VLAN Stacking in Multi-vendor <strong>Networks</strong> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .684 VLAN Stacking Packet Drop Precedence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .690 Enable Drop Eligibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .691 Honor the Incoming DEI Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .691 Mark Egress Packets with a DEI Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .692 Dynamic Mode CoS for VLAN Stacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .692 Layer 2 Protocol Tunneling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .695 Implementation Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .697 Enable Layer 2 Protocol Tunneling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .697 Specify a Destination MAC Address for BPDUs . . . . . . . . . . . . . . . . . . . . . . . . . . .698 Rate-limit BPDUs on the E-Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .698 Rate-limit BPDUs on the C-Series and S-Series . . . . . . . . . . . . . . . . . . . . . . . . . .698 Debug Layer 2 Protocol Tunneling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .699 Provider Backbone Bridging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .699 37 sFlow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 701 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .701
Implementation Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .702 Important Points to Remember . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .702 Enable and Disable sFlow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .703 Enable and Disable on an Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .703 sFlow Show Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .704 Show sFlow Globally . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .704 Show sFlow on an Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .704 Show sFlow on a Line Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .705 Specify Collectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .706 Polling Intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .706 Sampling Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .706 Sub-sampling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .707 Back-off Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .708 sFlow on LAG ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .708 Extended sFlow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .708 Important Points to Remember . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .709 38 Simple Network Management Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 711 Protocol Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 711 Implementation Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 711 Configure Simple Network Management Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 711 Related Configuration Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .712 Important Points to Remember . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .712 Create a Community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .712 Read Managed Object Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .713 Write Managed Object Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .714 Configure Contact and Location Information using SNMP . . . . . . . . . . . . . . . . . . . . . .714 Subscribe to Managed Object Value Updates using SNMP . . . . . . . . . . . . . . . . . . . . .715 Copy Configuration Files Using SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .718 Manage VLANs using SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .724 Create a VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .724 Assign a VLAN Alias . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .724 Display the Ports in a VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .725 Add Tagged and Untagged Ports to a VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .727 Enable and Disable a Port using SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .728 Fetch Dynamic MAC Entries using SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .728 Deriving Interface Indices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .730 39 Spanning Tree Protocol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 733 Protocol Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .733 Configuring Spanning Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .733 Related Configuration Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .733 Important Points to Remember . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .734 | 19
Page 1 and 2: FTOS Configuration Guide for the S6
Page 3 and 4: 1 About this Guide . . . . . . . .
Page 5 and 6: Linktrace Message and Response . .
Page 7 and 8: Jumpstart mode . . . . . . . . . .
Page 9 and 10: Viewing IGMP Enabled Interfaces . .
Page 11 and 12: 17 IPv6 Addressing. . . . . . . . .
Page 13 and 14: TIA-1057 (LLDP-MED) Overview . . .
Page 15 and 16: Configure a Static Rendezvous Point
Page 17: Honor the incoming dot1p value . .
Page 21 and 22: 42 System Time and Date . . . . . .
Page 23 and 24: About this Guide Objectives 1 This
Page 25 and 26: Configuration Fundamentals The FTOS
Page 27 and 28: Figure 2-2. CLI Modes in FTOS EXEC
Page 29 and 30: Table 2-1. FTOS Command Modes CLI C
Page 31 and 32: Obtaining Help Obtain a list of key
Page 33 and 34: Filtering show Command Outputs Filt
Page 35 and 36: Getting Started This chapter contai
Page 37 and 38: Table 3-1. Pin Assignments Between
Page 39 and 40: Figure 3-1. Completed Boot Process
Page 41 and 42: Configure the Management Port IP Ad
Page 43 and 44: Configure the Enable Password Acces
Page 45 and 46: Figure 3-4 shows an example of usin
Page 47 and 48: The output of the command dir also
Page 49 and 50: Figure 3-9. Alternative Storage Loc
Page 51 and 52: Management Management is supported
Page 53 and 54: Task Command Syntax Command Mode Al
Page 55 and 56: Apply a Privilege Level to a Userna
Page 57 and 58: Send System Messages to a Syslog Se
Page 59 and 60: Figure 4-2. show logging Command Ex
Page 61 and 62: Synchronize log messages You can co
Page 63 and 64: Enable FTP server To enable the sys
Page 65 and 66: To apply an IP ACL to a line: Task
Page 67 and 68: To change the timeout period or dis
Page 69 and 70:
If any user is already in CONFIGURA
Page 71 and 72:
Recovering from a Failed Start on t
Page 73 and 74:
802.1ag 802.1ag is available only o
Page 75 and 76:
These roles define the relationship
Page 77 and 78:
Enable Ethernet CFM Task Command Sy
Page 79 and 80:
Task Command Syntax Command Mode Fo
Page 81 and 82:
Continuity Check Messages Continuit
Page 83 and 84:
Figure 5-4. Linktrace Message and R
Page 85 and 86:
Three values are giving within the
Page 87 and 88:
802.1X 802.1X is supported on platf
Page 89 and 90:
3. The authenticator decapsulates t
Page 91 and 92:
Configuring 802.1X Configuring 802.
Page 93 and 94:
Figure 6-6. Verifying 802.1X Interf
Page 95 and 96:
Forcibly Authorizing or Unauthorizi
Page 97 and 98:
Configuring Timeouts If the supplic
Page 99 and 100:
Figure 6-11. Dynamic VLAN Assignmen
Page 101 and 102:
Figure 6-13. Configuring an Authent
Page 103 and 104:
Access Control Lists (ACL), Prefix
Page 105 and 106:
CAM optimization is supported on pl
Page 107 and 108:
V Implementing ACLs on FTOS One IP
Page 109 and 110:
• Loopback interfaces do not supp
Page 111 and 112:
Step Command Syntax Command Mode Pu
Page 113 and 114:
Configure an extended IP ACL Extend
Page 115 and 116:
Figure 7-7. Command Example: seq Fo
Page 117 and 118:
For information on MAC ACLs, refer
Page 119 and 120:
Figure 7-10. Creating an Ingress AC
Page 121 and 122:
Configuring ACLs to Loopback ACLs c
Page 123 and 124:
The following rules apply to prefix
Page 125 and 126:
Figure 7-14. Prefix List Force10(co
Page 127 and 128:
To view the configuration, use the
Page 129 and 130:
Figure 7-20. Resequencing Remarks F
Page 131 and 132:
Figure 7-21. Command Example: show
Page 133 and 134:
Also, if there are different instan
Page 135 and 136:
Command Syntax Command Mode Purpose
Page 137 and 138:
Border Gateway Protocol IPv4 (BGPv4
Page 139 and 140:
A stub AS is one that is connected
Page 141 and 142:
In order to make decisions in its o
Page 143 and 144:
BGP Attributes Routes learned via B
Page 145 and 146:
• AS_CONFED_SEQUENCE has a path l
Page 147 and 148:
One AS assigns the MED a value and
Page 149 and 150:
Next Hop The Next Hop is the IP add
Page 151 and 152:
Where the 2-Byte format is 1-65535,
Page 153 and 154:
Figure 8-10. Dynamic changes when b
Page 155 and 156:
Local-as is prepended before the ro
Page 157 and 158:
BGP Configuration To enable the BGP
Page 159 and 160:
Use these commands in the following
Page 161 and 162:
Figure 8-14 displays two neighbors,
Page 163 and 164:
Task Command Syntax Command Mode En
Page 165 and 166:
After you create a peer group, you
Page 167 and 168:
Figure 8-21. Command example: show
Page 169 and 170:
Page 171 and 172:
Only after the peer group responds
Page 173 and 174:
Figure 8-25. Allowas-in information
Page 175 and 176:
Filter on an AS-Path attribute The
Page 177 and 178:
Figure 8-27. Filtering with Regular
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Refer to Chapter 7, “Access Contr
Page 189 and 190:
Page 191 and 192:
Use the following commands in the C
Page 193 and 194:
To set dampening parameters via a r
Page 195 and 196:
Change BGP timers Use either or bot
Page 197 and 198:
Route map continue The BGP route ma
Page 199 and 200:
BGP Regular Expression Optimization
Page 201 and 202:
Figure 8-34. Viewing the Last Bad P
Page 203 and 204:
With full internet feed (205K) capt
Page 205 and 206:
Figure 8-38. Enable BGP - Router 1
Page 207 and 208:
Figure 8-40. Enable BGP - Router 3
Page 209 and 210:
Figure 8-42. Enable Peer Groups - R
Page 211 and 212:
Figure 8-44. Enable Peer Group - Ro
Page 213 and 214:
Bare Metal Provisioning 2.0 Bare Me
Page 215 and 216:
To display the currently configured
Page 217 and 218:
Following is an example of a config
Page 219 and 220:
2. The switch sends DHCP Discover o
Page 221 and 222:
Content Addressable Memory Content
Page 223 and 224:
Table 10-1. CAM Profile Description
Page 225 and 226:
The Layer 2 ACL CAM partition has s
Page 227 and 228:
When to Use CAM Profiling The CAM p
Page 229 and 230:
You must save the new CAM settings
Page 231 and 232:
Figure 10-6. View CAM-ACl settings
Page 233 and 234:
• The IPv4Flow configuration is a
Page 235 and 236:
L2PT 13 FRRP 5 You can re-configure
Page 237 and 238:
Figure 10-11. Returning to the defa
Page 239 and 240:
QoS CAM Region Limitation The defau
Page 241 and 242:
Skippy812 11 Dynamic Host Configura
Page 243 and 244:
Assigning an IP Address using DHCP
Page 245 and 246:
Configure the System to be a DHCP S
Page 247 and 248:
Specify a Default Gateway The IP ad
Page 249 and 250:
Create Manual Binding Entries An ad
Page 251 and 252:
To view the ip helper-address confi
Page 253 and 254:
Binding table entries are deleted w
Page 255 and 256:
Dynamic ARP Inspection Dynamic ARP
Page 257 and 258:
Use show arp inspection statistics
Page 259 and 260:
Step Task Command Syntax Command Mo
Page 261 and 262:
Force10 Resilient Ring Protocol For
Page 263 and 264:
If the Master node does not receive
Page 265 and 266:
• Multiple physical rings can be
Page 267 and 268:
• The Control VLAN is used to car
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
R1 MASTER interface GigabitEthernet
Page 275 and 276:
GARP VLAN Registration Protocol GAR
Page 277 and 278:
Figure 13-2. GVRP Configuration Ove
Page 279 and 280:
Based on the configuration in the e
Page 281 and 282:
Internet Group Management Protocol
Page 283 and 284:
Response Timers on page 288 for how
Page 285 and 286:
Figure 14-4. IGMP Membership Report
Page 287 and 288:
Figure 14-6. Viewing IGMP-enabled I
Page 289 and 290:
2. When a router receives a query i
Page 291 and 292:
Figure 14-10. Enabling IGMP Snoopin
Page 293 and 294:
Interfaces 15 This chapter describe
Page 295 and 296:
Figure 15-1. show interfaces Comman
Page 297 and 298:
To confirm that the interface is en
Page 299 and 300:
For information on enabling and con
Page 301 and 302:
To configure a Management interface
Page 303 and 304:
VLAN Interfaces VLANs are logical i
Page 305 and 306:
Port Channel Interfaces Port channe
Page 307 and 308:
The common speed is determined when
Page 309 and 310:
Figure 15-10. show interfaces port-
Page 311 and 312:
Figure 15-13. Command Example from
Page 313 and 314:
Load balancing through port channel
Page 315 and 316:
IPv4, IPv6, and non-IP traffic hand
Page 317 and 318:
• lsb — always uses the least s
Page 319 and 320:
Overlap port ranges If overlapping
Page 321 and 322:
Monitor interface statistics with t
Page 323 and 324:
To test the condition of cables on
Page 325 and 326:
When an E300 system boots up and a
Page 327 and 328:
Figure 15-30. Clearing Dampening Co
Page 329 and 330:
Enable Pause Frames Note: On the C-
Page 331 and 332:
Port-pipes A port pipe is a Dell Fo
Page 333 and 334:
Note: The show interfaces status co
Page 335 and 336:
Figure 15-34. show Commands with co
Page 337 and 338:
• L2ACL • L2FIB For remaining a
Page 339 and 340:
IPv4 Addressing IPv4 Addressing is
Page 341 and 342:
To assign an IP address to an inter
Page 343 and 344:
Figure 16-3. show ip route static C
Page 345 and 346:
Page 347 and 348:
In FTOS, Proxy ARP enables hosts wi
Page 349 and 350:
Page 351 and 352:
Configurable ARP Retries ICMP In FT
Page 353 and 354:
Important Points to Remember about
Page 355 and 356:
2. If UDP helper (using the command
Page 357 and 358:
Troubleshooting UDP Helper Display
Page 359 and 360:
IPv6 Addressing IPv6 Addressing, ap
Page 361 and 362:
IPv6 Headers The IPv6 header has a
Page 363 and 364:
Table 17-1. Next Header field value
Page 365 and 366:
• 2001:0db8:0000:0000:0000:0000:1
Page 367 and 368:
Table 17-2. FTOS and IPv6 Feature S
Page 369 and 370:
Path MTU (Maximum Transmission Unit
Page 371 and 372:
• Multicast Listener Discovery Pr
Page 373 and 374:
Page 375 and 376:
Assign a Static IPv6 Route IPv6 Sta
Page 377 and 378:
Page 379 and 380:
Figure 17-7 illustrates the show ip
Page 381 and 382:
Page 383 and 384:
iSCSI Optimization iSCSI Optimizati
Page 385 and 386:
The following message is displayed
Page 387 and 388:
Default iSCSI Optimization Values T
Page 389 and 390:
Link Aggregation Control Protocol L
Page 391 and 392:
FTOS supports LAGs in the following
Page 393 and 394:
Set the LACP long timeout PDUs are
Page 395 and 396:
Step Task Command Command Mode 2 Cr
Page 397 and 398:
Figure 19-10. Enabling Hitless LACP
Page 399 and 400:
Figure 19-14. Inspecting Configurat
Page 401 and 402:
Summary of the configuration on ALP
Page 403 and 404:
Figure 19-18. Using the show interf
Page 405 and 406:
Figure 19-20. Using the show lacp C
Page 407 and 408:
Layer 2 Layer 2 features are suppor
Page 409 and 410:
Display the MAC Address Table To di
Page 411 and 412:
mac learning-limit no-station-move
Page 413 and 414:
An individual MAC learning limit ca
Page 415 and 416:
When NIC teaming is employed, consi
Page 417 and 418:
Configuring the Switch for Microsof
Page 419 and 420:
• You may not enable any Layer 2
Page 421 and 422:
Figure 20-10. Configuring Far-end F
Page 423 and 424:
Step Task Command Syntax Command Mo
Page 425 and 426:
During an RPM Failover In the event
Page 427 and 428:
Link Layer Discovery Protocol Link
Page 429 and 430:
Management TLVs A Management TLV is
Page 431 and 432:
TIA Organizationally Specific TLVs
Page 433 and 434:
LLDP-MED Network Policies TLV A net
Page 435 and 436:
• Viewing Information Advertised
Page 437 and 438:
• If you configure an interface,
Page 439 and 440:
Figure 21-12. Viewing All Informati
Page 441 and 442:
Figure 21-14. Configuring LLDPDU Tr
Page 443 and 444:
Figure 21-16. debug lldp detail—L
Page 445 and 446:
Table 21-8. LLDP System MIB Objects
Page 447 and 448:
Table 21-10. LLDP-MED System MIB Ob
Page 449 and 450:
Multiple Spanning Tree Protocol Mul
Page 451 and 452:
• Preventing Network Disruptions
Page 453 and 454:
Influence MSTP Root Selection MSTP
Page 455 and 456:
Task Command Syntax Command Mode Ch
Page 457 and 458:
To enable EdgePort on an interface,
Page 459 and 460:
Figure 22-10. Router 1 Running-conf
Page 461 and 462:
Figure 22-12. Router 3 Running-conf
Page 463 and 464:
Figure 22-14. Displaying BPDUs and
Page 465 and 466:
Multicast Features Multicast Featur
Page 467 and 468:
Implementation Information • Beca
Page 469 and 470:
• If the limit is decreased after
Page 471 and 472:
Rate Limit IGMP Join Requests If yo
Page 473 and 474:
Prevent a PIM Router from Processin
Page 475 and 476:
Multicast Traceroute Multicast Trac
Page 477 and 478:
FTOS provides the ability to adjust
Page 479 and 480:
24 Open Shortest Path First (OSPFv2
Page 481 and 482:
Figure 24-1. Autonomous System Area
Page 483 and 484:
Figure 24-2. OSPF Routing Examples
Page 485 and 486:
Link-State Advertisements (LSAs) A
Page 487 and 488:
Figure 24-3. Priority and Costs Exa
Page 489 and 490:
Multi-Process OSPF allows multiple
Page 491 and 492:
To ensure equal intervals between t
Page 493 and 494:
Return to CONFIGURATION mode to ena
Page 495 and 496:
In CONFIGURATION ROUTER OSPF mode,
Page 497 and 498:
Loopback interfaces also assist in
Page 499 and 500:
Use the following command in the RO
Page 501 and 502:
Figure 24-14 shows the convergence
Page 503 and 504:
Figure 24-16. Changing the OSPF Cos
Page 505 and 506:
Page 507 and 508:
Filter routes To filter routes, use
Page 509 and 510:
Troubleshooting OSPFv2 FTOS has sev
Page 511 and 512:
Use the following command in EXEC P
Page 513 and 514:
Assign OSPFv3 Process ID and Router
Page 515 and 516:
Redistribute routes You can add rou
Page 517 and 518:
Use the following command in EXEC P
Page 519 and 520:
PIM Sparse-Mode PIM Sparse-Mode is
Page 521 and 522:
source, including the RP, create an
Page 523 and 524:
Figure 25-3. Viewing the PIM Multic
Page 525 and 526:
Override Bootstrap Router Updates P
Page 527 and 528:
Enable PIM-SM graceful restart (non
Page 529 and 530:
PIM Source-Specific Mode PIM Source
Page 531 and 532:
Implementation Information • The
Page 533 and 534:
• When an extended ACL is associa
Page 535 and 536:
Figure 26-4. Configuring PIM-SSM wi
Page 537 and 538:
Power over Ethernet Power over Ethe
Page 539 and 540:
Related Configuration Tasks • Man
Page 541 and 542:
View the total power consumption of
Page 543 and 544:
Extended Power-via-MDI TLV The PD s
Page 545 and 546:
Manage Power Priorities PoE-enabled
Page 547 and 548:
Figure 27-6. Order of PoE Re-Supply
Page 549 and 550:
Figure 27-9. LLDP Configuration for
Page 551 and 552:
Port Monitoring Port Monitoring is
Page 553 and 554:
On the E-Series TeraScale, FTOS sup
Page 555 and 556:
Figure 28-4. Number of Monitoring P
Page 557 and 558:
Figure 28-7. Port Monitoring Exampl
Page 559 and 560:
Figure 28-8. Configuring Flow-based
Page 561 and 562:
Private VLANs FTOS 7.8.1.0 adds a P
Page 563 and 564:
Each of the port types can be any t
Page 565 and 566:
Creating a Primary VLAN A primary V
Page 567 and 568:
Figure 29-2. Configuring VLANs for
Page 569 and 570:
• show vlan private-vlan mapping:
Page 571 and 572:
Per-VLAN Spanning Tree Plus Per-VLA
Page 573 and 574:
• PVST+ in Multi-vendor Networks
Page 575 and 576:
Figure 30-4. Display the PVST+ Forw
Page 577 and 578:
Task Command Syntax Command Mode Ch
Page 579 and 580:
Figure 30-5. PVST+ with Extend Syst
Page 581 and 582:
Figure 30-7. PVST+ Sample Configura
Page 583 and 584:
Quality of Service Quality of Servi
Page 585 and 586:
Figure 31-1. Dell Force10 QoS Archi
Page 587 and 588:
On the C-Series and S-Series you ca
Page 589 and 590:
Figure 31-7. Displaying How Your Ra
Page 591 and 592:
Figure 31-10. Using the Order Keywo
Page 593 and 594:
FTOS Behavior: An explicit “deny
Page 595 and 596:
Figure 31-12. Marking DSCP Values f
Page 597 and 598:
Create Input Policy Maps There are
Page 599 and 600:
By default, if no match occurs, the
Page 601 and 602:
Apply an output QoS policy to a que
Page 603 and 604:
You can create a custom WRED profil
Page 605 and 606:
Figure 31-15. show qos statistics C
Page 607 and 608:
• Status indicates whether or not
Page 609 and 610:
Figure 31-19. Classifying VOIP Traf
Page 611 and 612:
Routing Information Protocol Routin
Page 613 and 614:
Configuration Task List for RIP •
Page 615 and 616:
Control RIP routing updates By defa
Page 617 and 618:
Figure 32-3 shows an example of the
Page 619 and 620:
Summarize routes Routes in the RIPv
Page 621 and 622:
Configuring RIPv2 on Core 2 Figure
Page 623 and 624:
RIP Configuration on Core 3 Figure
Page 625 and 626:
RIP Configuration Summary Figure 32
Page 627 and 628:
Remote Monitoring Remote Monitoring
Page 629 and 630:
Set rmon alarm To set an alarm on a
Page 631 and 632:
Figure 33-2. rmon event Command Exa
Page 633 and 634:
Rapid Spanning Tree Protocol Rapid
Page 635 and 636:
To configure the interfaces for Lay
Page 637 and 638:
Figure 34-5. show spanning-tree rst
Page 639 and 640:
Table 34-2 displays the default val
Page 641 and 642:
FTOS Behavior: Regarding bpduguard
Page 643 and 644:
Security Security features are supp
Page 645 and 646:
Suppress AAA Accounting for null us
Page 647 and 648:
Configure login authentication for
Page 649 and 650:
To use local authentication for ena
Page 651 and 652:
To configure a username and passwor
Page 653 and 654:
Page 655 and 656:
To move to a lower privilege level,
Page 657 and 658:
• Monitor RADIUS on page 659 (opt
Page 659 and 660:
To set global communication paramet
Page 661 and 662:
Figure 35-4. Failed Authentication
Page 663 and 664:
To delete a TACACS+ server host, us
Page 665 and 666:
Figure 35-6. Specifying an SSH vers
Page 667 and 668:
Figure 35-8. Enabling SSH Password
Page 669 and 670:
Figure 35-12. Client-based SSH Auth
Page 671 and 672:
Since traffic passes through the fi
Page 673 and 674:
Figure 35-13. Trace list Using seq
Page 675 and 676:
Figure 35-14. Trace List Example Fo
Page 677 and 678:
Figure 35-16. Example Access-Class
Page 679 and 680:
Service Provider Bridging Service P
Page 681 and 682:
Create Access and Trunk Ports An ac
Page 683 and 684:
FTOS Options for Trunk Ports 802.1a
Page 685 and 686:
Figure 36-6. TPID Match and First-b
Page 687 and 688:
Figure 36-8. First-byte TPID Match
Page 689 and 690:
Figure 36-10. Single and Double-tag
Page 691 and 692:
Enable Drop Eligibility You must en
Page 693 and 694:
Figure 36-12. Statically and Dynami
Page 695 and 696:
To map C-Tag dot1p values to S-Tag
Page 697 and 698:
Figure 36-14. VLAN Stacking with L2
Page 699 and 700:
Debug Layer 2 Protocol Tunneling Ta
Page 701 and 702:
sFlow Configuring sFlow is supporte
Page 703 and 704:
• FTOS exports all sFlow packets
Page 705 and 706:
Page 707 and 708:
The sflow sample-rate command, when
Page 709 and 710:
Figure 37-6. Confirming that Extend
Page 711 and 712:
Simple Network Management Protocol
Page 713 and 714:
View your SNMP configuration, using
Page 715 and 716:
Task Command Command Mode Identify
Page 717 and 718:
Table 38-2. Dell Force10 Enterprise
Page 719 and 720:
The relevant MIBs for these functio
Page 721 and 722:
Table 38-4. Copying Configuration F
Page 723 and 724:
Dell Force10 provides additional MI
Page 725 and 726:
Figure 38-16. Assign a VLAN Alias u
Page 727 and 728:
The value 40 is in the first set of
Page 729 and 730:
Each object is comprised an OID con
Page 731 and 732:
Figure 38-27. Binary Representation
Page 733 and 734:
Spanning Tree Protocol Spanning Tre
Page 735 and 736:
Configuring Interfaces for Layer 2
Page 737 and 738:
Figure 39-4. Spanning Tree Enabled
Page 739 and 740:
Modifying Global Parameters You can
Page 741 and 742:
To enable PortFast on an interface:
Page 743 and 744:
Figure 39-8. Enabling BPDU Guard Fo
Page 745 and 746:
Stacking S-Series Switches Stacking
Page 747 and 748:
Figure 40-2. Electing the Stack Man
Page 749 and 750:
Figure 40-4. Adding a Standalone wi
Page 751 and 752:
Figure 40-6. Adding a Standalone wi
Page 753 and 754:
You may stack any combination of S-
Page 755 and 756:
Figure 40-11. Stacking Cable Redund
Page 757 and 758:
Figure 40-13. Adding a Stack Unit w
Page 759 and 760:
Figure 40-16. Removing a Stack Memb
Page 761 and 762:
Split an S-Series Stack To split a
Page 763 and 764:
Figure 40-18. Displaying Informatio
Page 765 and 766:
Influence Management Unit Selection
Page 767 and 768:
Figure 40-21. Recovering from a Sta
Page 769 and 770:
Storm Control Storm Control is supp
Page 771 and 772:
System Time and Date 42 Chapter 42,
Page 773 and 774:
Figure 42-1. NTP Fields Leap Indica
Page 775 and 776:
Set the Hardware Clock with the Tim
Page 777 and 778:
Configure NTP authentication NTP au
Page 779 and 780:
• Root Delay (sys.rootdelay, peer
Page 781 and 782:
The software clock runs only when t
Page 783 and 784:
Set Daylight Saving Time Once Set a
Page 785 and 786:
Page 787 and 788:
Upgrade Procedures Find the upgrade
Page 789 and 790:
Virtual LANs (VLAN) VLANs are suppo
Page 791 and 792:
Untagged interfaces must be part of
Page 793 and 794:
Figure 44-3. show vlan Command Exam
Page 795 and 796:
Use the untagged command to move un
Page 797 and 798:
Native VLAN support breaks this bar
Page 799 and 800:
Virtual Router Redundancy Protocol
Page 801 and 802:
VRRP Benefits With VRRP configured
Page 803 and 804:
Task Command Syntax Command Mode Fi
Page 805 and 806:
Figure 45-6. Command Example Displa
Page 807 and 808:
Configure simple authentication wit
Page 809 and 810:
Figure 45-13. Command Example: adve
Page 811 and 812:
Figure 45-17. Configure VRRP Router
Page 813 and 814:
S-Series Debugging and Diagnostics
Page 815 and 816:
Figure 46-2. Verifying the Offline/
Page 817 and 818:
Figure 46-5. Viewing the Results of
Page 819 and 820:
Table 46-2. show hardware Commands
Page 821 and 822:
Table 46-3 describes the type and n
Page 823 and 824:
Buffer tuning commands Task Command
Page 825 and 826:
Using a pre-defined buffer profile
Page 827 and 828:
The S60 switch has two ASICS; each
Page 829 and 830:
Figure 46-14. Displaying Drop Count
Page 831 and 832:
Displaying Stack Port Statistics Th
Page 833 and 834:
Figure 46-19. Mini application core
Page 835 and 836:
Standards Compliance This appendix
Page 837 and 838:
General IPv4 Protocols RFC# Full Na
Page 839 and 840:
Border Gateway Protocol (BGP) RFC#
Page 841 and 842:
Intermediate System to Intermediate
Page 843 and 844:
Multicast RFC# Full Name S-Series C
Page 845 and 846:
Network Management (continued) RFC#
Page 847 and 848:
IEEE 802.1AB The LLDP Management In
Page 849 and 850:
MIB Location Force10 MIBs are under
Page 851 and 852:
Index Numerics 10/100/1000 Base-T E
Page 853 and 854:
FRRP 261 FRRP Master Node 261 FRRP
Page 855 and 856:
MTU Size, Configuring on an Interfa
Page 857 and 858:
show ip ssh command 664 show ip ssh
show all

8.3.3.8 - Force10 Networks

Create successful ePaper yourself

Delete template?

Save as template?