Heatlock ESB2, Electric Sprue Bushing

More documents

Recommendations

Info

This Heatlock series, below, is currently being replaced by the A1-series of nozzles. Before you design check availability, stock is gradually decreased. Spare parts will be available until at least end of 2007 (apart form NPT1 bodies) Heatlock ESB2, Electric Sprue Bushing ESB2 Features • Lowest possible thermal stress on the plastic • Exceptionally uniform heat distribution along the sprue bushing. • Ceramic insulation between bushing and mould. • Low power consumption. Egenskaper • Utomordentligt jämn värmefördelning längs bussningen. • Bussningen går att använda med i stort sett alla av dagens existerande material. • Minsta möjliga termiska påkänning på plasten. • Låg effektförbrukning. 28 L=26-136 +20 Ø50 Shot weights
This Heatlock series, below, is currently being replaced by the A1-series of nozzles. Before you design check availability, stock is gradually decreased. Spare parts will be available until at least end of 2007 (apart form NPT1 bodies) ESB2 1 Ø6 Ø50f8 Ø48 ”L” mm Single-cav. Part No. Multi-cav.* Total volume of feed channel in mm 3 28 +0 -0,05 9,5 26 ESB2026101 ESB2026102 1378 26+20 ESB2026201 ESB2026202 2006 46 ESB2046101 ESB2046102 1943 46+20 ESB2046201 ESB2046202 2572 “L” Ø24 66 ESB2066101 ESB2066102 2508 66+20 ESB2066201 ESB2066202 3137 86 ESB2086101 ESB2086102 3074 6 86+20 ESB2086201 ESB2086202 3702 Ø2 106 ESB2106201 ESB2106102 3639 +20 Taper of the gate 3 degrees “inc.” Ø12h6 106+20 ESB2106201 ESB2106202 4267 136 ESB2136101 ESB2136102 4487 136+20 ESB2136201 ESB2136202 5115 * with O-ring 608 Can be controlled with various types of temperature controllers intended for hot runner systems with 220/240 V using thermocouple of type Fe-CuNi. 15,5 Recommended for the following maximum shot weights: Low-viscosity plastic (PS,PE,PP) Med.-viscosity plastic (ABS,SAN, PA,POM) High-viscosity plastic (PC,PMMA, Noryl, Filled material) 400g 300g 150g Gate diameter is Ø2 mm on delivery, can be reamed up to Ø5 mm if needed. Please, look at page 9 regarding gate diameter. Length expansion at: °C=”L”+X,xx Ø27 °C 26 46 66 86 106 136 9 200 0,06 0,11 0,15 0,20 0,24 0,31 Ø10,4 +0,01 -0 250 0,07 0,13 0,19 0,25 0,30 0,40 20 8 R04 max Ø50 H7 20 2,5 300 0,09 0,16 0,23 0,30 0,37 0,47 350 0,10 0,19 0,27 0,35 0,43 0,55 Ø28 65° +0,01 8 To ensure minimum vestige on the part, measure the actual "L" measurement on each bush, add the length expansion according to the table to get the hole depth ("L"+X,xx) to be drilled in the cavity plate. ”L” 2 R3 Före inbyggnad, mät upp bussningens nominella "L"-mått, lägg därefter till längdutvidgningen så att bussningens spets ligger exakt vid intagspunkten i uppvärmt tillstånd. Ø12 H7 Ø0,01 Ø27 5 ”L” 9 max 1.5 0,25-0,5 2 Ø12 3 R=1 ØD ØD(D+4) Gate on runner or on surface not perpendicular to bushing. Increased temperature in the front end of the bush due to reduced heat loss. more 2.02.2 Date: 030928, © LKM Heatlock Co Ltd
Page 2 and 3: This Heatlock series, below, is cur
Page 64 and 65: Cartridge Heaters This Heatlock ser
Page 66 and 67: Coilheater This Heatlock series, be
Page 68 and 69:
Thermocouples This Heatlock series,
Page 70 and 71:
This Heatlock series, below, is cur
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
34.5 7.5 This Heatlock series, belo
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
DIGITAL CONTROLLERS This Heatlock s
Page 138 and 139:
DIGITAL CONTROLLERS This Heatlock s
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
8 7 This Heatlock series, below, is
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
show all

Heatlock ESB2, Electric Sprue Bushing

Create successful ePaper yourself

Delete template?

Save as template?