Firmware History for VG Series

Firmware History for
CamServer VG 2c, CamDisc VG 2c, CamDisc VG 2s,
CamDisc VG 4, CamDisc VG 10, CamDisc VG 4s,
CamDisc VG 10s, CamTel VG 4, CamTel VG 10,
Cam4mobile VG 2c, Cam4mobile VG 4,
Cam4mobile VG 10s, CamDisc VG HNVR
(Serial number: CCxxxxxx, VFxxxxxx, VXxxxxxx, DCxxxxxx, STxxxxxx, SFxxxxxx,
SXxxxxxx, CFxxxxxx, CXxxxxxx, MCxxxxxx, MFxxxxxx, MXxxxxxx, VNxxxxxx)
Firmware V4.16 2013-10-31
(Support of all functions only with CamControl LITE 4.24 or higher)
• Devices can be armed/disarmed via the VdS interface “VdS 2465 TCP/IP für Video“
for alarm panels
• The privacy zone function for analogue cameras can now work in three different
modes:
o “Always”: Configured privacy zone is active permanently
o “Only if not armed“: Privacy zone is only active when the device is
o
disarmed
“Off after alarm until disarm”: Privacy zone will be deactivated when an
alarm is triggered and stay deactivated until the device is disarmed
• Option added to use active or passive antennas in device settings “Wireless WAN”
with device series CamServer VG 2c, CamDisc VG 2c and Cam4mobile VG 2c
Note: To support this feature a hardware modification might be necessary
• Changes and bug fixes:
o
o
Archive default factory settings corrected
Archive file protection modified
Firmware V4.14 2013-10-15
(Support of all functions only with CamControl LITE 4.23 or higher)
• Option added to Video Gateways to automatically start video recording
(continuous recording) when the device is armed
• Support of new 3G/GPS Module for CamServer VG 2c, CamDisc VG 2c and
Cam4mobile VG 2c
• Various Bug fixes:
o Minor corrections of armed/disarmed status
o Camera position authentication corrected with CamDisc VG HNVR
o IP camera support for Panogenics improved
o IP camera support for Vista Elcipse 2 improved
Firmware V4.12 2013-08-30
(Support of all functions only with CamControl LITE 4.20 or higher)
• Integration of several IP cameras from the following manufacturers (see IP camera
compatibility list):
o AMTK (JPEG, MJPEG, H.264, PTZ, VMD)
o AVE (JPEG, MJPEG, H.264, VMD)
o Eneo (JPEG, MJPEG, H.264, PTZ, VMD)
o Mobotix Q24 (rectified archive playback incl. virtual PTZ control)
o Novus (JPEG, MJPEG, H.264, VMD)
1/3

o Santec (JPEG, MJPEG, H.264, PTZ, VMD)
• Various changes of default factory settings
• Various bug fixes:
o CamServer VG 2c, CamDisc VG 2c und Cam4mobile VG 2c: Serial PTZ
interface without function
o Sequencer Mode (V out) ‘Display camera of latest alarm’ and ‘Display
camera of latest image recording’ corrected
o H.264 video format of IndigoVision IP camera corrected
Firmware V4.10 2013-07-02
(Support of all functions only with CamControl LITE 4.18 or higher)
o Free definable pre-alarm sequence (1-30s)
o Free definable post-alarm sequence (0-15s)
o PreAlarmViewer supports up to three cameras in parallel
• CamTel VG, CamDisc VG/VGs: Monitor output (Vout sequencer mode) corrected
• CamServer VG 2c, CamDisc VG 2c, Cam4mobile VG 2c: Modifications of
“Sierra Wireless“ 3G/GPS Module
Firmware V4.08 2013-06-03
(Firmware V4.08 is not available for CamDisc VG HNVR series)
• Fan control behaviour corrected
• Improved GPS position update
• CamServer VG 2c/Cam4mobile VG 2c: „DSP 2 error“ corrected
Firmware V4.06 2013-04-23
(Support of all functions only with CamControl LITE/PRO 4.15 or higher)
• Remote device reset via CamControl LITE
o Connection settings (IP address, DNS, port, modem settings, alarm
numbers, HTconnect numbers..) can be kept optionally
o Archive images and archive configuration can be kept optionally
• Logfile entries added for BS8418, VDS and the reset function
• Usage of external RAID systems/hard drives without secure code. This option will
be enabled in case of a “licence key formatted hard drive” (RAID-ID) is inserted in
HeiTel device
• Automatic “Delete all pictures older than x days” for event recording added
• Firmware determination of “sierra Wireless” card in Wireless WAN settings added
• Support of transmitter with serial no. VZxxxxxx
• CamServer VG 2c/Cam4mobile VG 2c: Internal network communication with
3GGPS module optimised
2/3

Firmware V4.04 2013-02-20
(Support of all functions only with CamControl LITE/PRO 4.15 or higher)
• Motion detection from Samsung and Visicom IP cameras integrated
• Integration of Axis and Visicom IP cameras via H.264 (CamDisc VG HNVR only)
• Integration of Arecont IP cameras via MJPEG
• Various bug-fixes
o Pre-alarm image evaluation with CamTel VG devices corrected (DSP
failure)
o ONVIF protocol modifications
o Philips software remote adapter corrected
o “DSP error” behaviour corrected
• CamTel VG: Error LED and Error Relay behaviour from CamDisc VG adopted
• CamTel VG: Video loss detection of IP cameras within 60s (user online) and within
30s (no user online) added
• Battery buffered logfile will be deleted during device hardware reset.
• CamDisc VG HNVR: Log file entry “HDD deactivated“ via Aux 2 input added
Firmware V4.02 2012-11-20
(Support of all functions only with CamControl LITE/PRO 4.12 or higher)
• Initial release
3/3