LanTEKÂ® II Series Manual - Ideal Industries Inc.

More documents

Recommendations

Info

LanTEK ® II Cable Certifier Instruction Manual This instruction manual contains information proprietary to IDEAL INDUSTRIES, INC. The information in this document is not to be used or duplicated in any manner without prior written approval from IDEAL INDUSTRIES, INC. IDEAL INDUSTRIES, INC. and the IDEAL INDUSTRIES, INC. logo are registered trademarks of IDEAL INDUSTRIES, INC. All other product names mentioned in this manual are trademarked or copyrighted by their respective manufacturers. IDEAL INDUSTRIES, INC. 9650 Chesapeake Drive San Diego, CA 92123 Phone: (800) 854-2708 Phone: (858) 627-0100 Fax: (858) 715-7003 Manual Part No.: P-2877 Rev. B © 2009 IDEAL INDUSTRIES, INC. 2009-12 1
Standard Warranty Policy of IDEAL INDUSTRIES, INC. The General Terms and Conditions of the local subsidiary of IDEAL INDUSTRIES, INC. apply. Safety Precautions Exercise caution when handling rechargeable batteries (accumulators) All lithium-ion battery packs (Li-ion), regardless of their indicated charge state, are capable of producing electrical current sufficient to cause personal injury and/or property damage. Do not dispose of lithium-ion battery packs (Li-ion) in a fire or with regular waste. Lithiumion battery packs (Li-ion) may explode if exposed to open flame. The battery packs are hazardous waste and may contaminate ground water sources if disposed of in landfills. IDEAL INDUSTRIES, INC. tries to provide the maximum protection possible by installing an automatic reset fuse in the battery packs, to help stop high current discharge as quickly as possible. However, these fuses may not completely protect against a momentary arc discharge, which can result if the battery pack's electrical contacts are shorted. The following battery pack handling precautions must be closely followed to avoid risk of injury. ‣ When a battery pack is not installed in the Display (DH) or Remote (RH) handset, it should be kept in a clean, dry, non-conductive package. ‣ Keep conductive materials away from the battery pack at all times. ‣ Keep contact sides of the battery pack away from each other at all times. ‣ Battery packs can be charged while in the Display (DH) and in the Remote (RH) handset, but also externally with the adapter. Charging in any other manner may cause the battery pack to explode. ‣ Always install, remove, store, and charge the battery packs in a non-explosive atmosphere. ‣ Observe operating and storage temperatures (see chapter 1.3. Dimensions, Weights, Operating Conditions). ‣ Do not allow children or persons unfamiliar with the precautionary instructions in this manual to handle or recharge the battery packs. ‣ Do not open the battery pack case. There are no user-serviceable parts inside the case, and the batteries in the case are not replaceable. 2
Page 1: LanTEK ® II Series Manual 0
Page 5 and 6: Table of contents CHAPTER 1 Your La
Page 7 and 8: Table of contents 6.11.1. Insertion
Page 9 and 10: Table of contents 13.1. Technical S
Page 11 and 12: Chapter 1 Your LanTEK ® II Cable C
Page 13 and 14: CHAPTER 2 Product Description 2.1.
Page 15 and 16: Chapter 2 Product Description 2.1.2
Page 17 and 18: Chapter 2 Product Description 2.2.
Page 19 and 20: 2.3. Power Management Chapter 2 Pro
Page 21 and 22: CHAPTER 3 Basics of the Cable Test
Page 23 and 24: Chapter 4 Preferences 1. Use Arrow
Page 25 and 26: Chapter 4 Preferences 1. Use Arrow
Page 27 and 28: Chapter 4 Preferences 6. Use soft k
Page 29 and 30: CHAPTER 5 Autotest Using Autotest,
Page 31 and 32: Chapter 5 Autotest Autotest Pref Th
Page 33 and 34: Chapter 5 Autotest 2. Use Arrow Key
Page 35 and 36: Chapter 5 Autotest 5.3.1. Simple Ca
Page 37 and 38: Chapter 5 Autotest 3. Use Alphanume
Page 39 and 40: Chapter 5 Autotest 5.4.1. Cable Nam
Page 41 and 42: Chapter 5 Autotest AAA A / AAA A -
Page 43 and 44: Chapter 5 Autotest Illustration 2 5
Page 45 and 46: Chapter 5 Autotest 20. Make correct
Page 47 and 48: Chapter 5 Autotest 5.6. DualMODE Fu
Page 49 and 50: Chapter 5 Autotest Illustration 2 5
Page 51 and 52: Chapter 5 Autotest 5.9. Calibration
Page 53 and 54:
Chapter 5 Autotest 5.9.2. Coaxial C
Page 55 and 56:
Chapter 5 Autotest 3. Use soft key
Page 57 and 58:
Chapter 5 Autotest Illustration 4 5
Page 59 and 60:
CHAPTER 6 Structured Cabling Testin
Page 61 and 62:
Chapter 6 Structured cabling testin
Page 63 and 64:
Page 65 and 66:
6.11. Insertion Loss Test (Attenuat
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
CHAPTER 8 Fiber Testing with FiberT
Page 75 and 76:
Chapter 8 Fiber testing (LWL) Fiber
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
CHAPTER 9 Tone Generator 9.1. Tone
Page 89 and 90:
CHAPTER 10 IDEAL DataCENTER Softwar
Page 91 and 92:
Chapter 10 IDEAL DataCENTER Softwar
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Chapter 11 LanTEK Firmware Upgrade
Page 107 and 108:
Standards Organization Classificati
Page 109 and 110:
Chapter 13 Customer Service North/S
show all

LanTEKÂ® II Series Manual - Ideal Industries Inc.

Create successful ePaper yourself

Delete template?

Save as template?