SB 300 - JBL.com
SB 300 - JBL.com
SB 300 - JBL.com
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>SB</strong> <strong>300</strong><br />
<strong>SB</strong><strong>300</strong> SoundBar<br />
30W x 2 Soundbar system<br />
LINE VOLTAGE Yes/No Hi/Lo Line Nom. Unit Notes<br />
US 120vac/60Hz Yes 108-132 120 Vrms Normal Operation<br />
EU 230vac/50-60Hz Yes 207-253 230 Vrms Normal operation, MOMS required<br />
Parameter Specification Unit<br />
QA Test<br />
Limits Conditions Notes<br />
SYSTEM PERFORMANCE USING LOCAL INPUTS<br />
Amp Section<br />
Type (Class AB, D, other) D n/a n/a<br />
Load Impedance (speaker) 4 Ohms n/a Nominal<br />
Rated Output Power 30 Watts 28<br />
THD @ Rated Power 0.5 % 1 22K filter<br />
THD @ 1 Watt 0.2 % 0.3 22K filter<br />
DC Offset 12 mV-DC 30<br />
Damping factor 5 DF 5<br />
Measured at speaker connectors<br />
90% of rated power<br />
Input Sensitivity local<br />
Input Frequency 1 KHz n/a Nominal Freq. Volume level at maximum<br />
L or R 53 mVrms ±1dB To 1 Watt<br />
System Gain (L or R inputs) 32 dB ±1dB<br />
Signal to Noise<br />
SNR-A-Weighted 65 dBA 62 relative to 1W A-Weighting filter (Volume at max)<br />
SNR-unweighted 62 dBr 60 relative to 1W 22K filter (Volume at max.)<br />
Volume @max, w/ A/P Swept<br />
Bandpass Measurement (Line<br />
Residual Noise Floor 10K Ohms n/a Nominal<br />
Filters<br />
EQ Modes 2 Table mount and wall mount settings<br />
Power BW<br />
THD+N vs Frequency, 20-<br />
20KHz 55 Volume at maximum<br />
10KHz 60 dB >55 Volume at maximum<br />
Local Input dynamic range<br />
Test frequency 1 KHz<br />
Maximum input voltage without<br />
distorting output signal 2 Vrms functional<br />
With volume level at 1/4 of full scale<br />
increase input level and verify THD<br />
at the output, record the maximum<br />
input level that produces THD<br />
below 1%<br />
Subwoofer output YES Through the wireless Tx<br />
Features --<br />
The purpose of this test is to verify how much voltage<br />
the front end can take before it is overdriven, volume<br />
is set low to prevent the output stage from clipping<br />
Push type buttons to control volume level, and to<br />
scroll through the different surround/effects, source<br />
Front panel controls<br />
selection and power/mute On/Off<br />
DSP processing YES n/a Verify 1 Surround mode, Stereo Modes<br />
Credit card type<br />
remote control unit YES n/a functional<br />
Wireless ready YES n/a functional<br />
Wireless range Tx section >50 ft functional<br />
Volume up and down, surround, bypass, effect mode<br />
and source selection and power On/Off control.<br />
2.4G, Wireless unit must be able to Tx, Subwoofer<br />
signal<br />
Front panel LED Indicator(s) YES n/a functional<br />
System must be provided with LED's indicators,<br />
intended to provide feedback to the end user on<br />
active surround or decoding modes includiing power.<br />
Digital Input YES n/a functional Optical connector<br />
Analog inputs YES n/a functional Stereo RCA Jack (RED-WHT)<br />
Internal power supply YES n/a functional Power supply Class II<br />
25