alithicon “fleet” synthetic enclosed gear and transmission lubricants

ALITHICON “FLEET” SYNTHETIC 

ENCLOSED GEAR AND TRANSMISSION LUBRICANTS 

THE ALITHICON “FLEET” SYNTHETIC ENCLOSED GEAR AND TRANSMISSION LUBRICANTS ARE 

DESIGNED AND FORMULATED FOR USE IN MANUAL TRANSMISSIONS, TRANSFER CASES, 

DIFFERENTIALS, AND OIL-LUBRICATED WHEEL BEARINGS FOUND IN PASSENGER CARS, 

TRUCK DIFFERENTIALS, FARM TRACTORS, TRAILER WHEEL BEARINGS, CONSTRUCTION, AND 

MISCELLANEOUS OTHER INDUSTRIAL EQUIPMENT. 

THE ALITHICON “FLEET” SYNTHETIC LONG-LIFE LUBRICANTS ARE RECOMMENDED FOR USE IN 

INDUSTRIAL GEAR DRIVES ALSO. 

BLENDED WITH HIGH-VISCOSITY INDEX, LOW POUR POINT SYNTHETIC BASE-STOCKS, AND 

COMPOUNDED WITH THE EXCLUSEIVE ALITHICON LOAD-CARRYING ADDITIVE, THESE 

LUBRICANTS PROVIDE MAXIMUM PROTECTION TO GEARS AND BEARINGS OPERATING OVER A 

WIDE RANGE OF TEMPERATURES, SPEEDS, AND LOADS. THE SUPERB RESISTANCE TO 

OXIDATION PROVIDES THE BENEFIT OF EXTENDED DRAIN INTERVALS. 

USER BENEFITS: 

* STOPS SEAL LEAKAGE * WILL NOT MIX WITH WATER 

* REDUCES AMPS IN INDUSTRIAL GEAR DRIVES * NON-FOAMING 

* RATES AN O.K. TIMKEN LOAD OF 100 lbs, MIN. * LOW POUR POINT OF -20° F 

* REDUCES AND ELIMINATES GEAR REDUCER NOISE * EXTENDED DRAIN INTERVALS 

* EXTENDS GEAR AND BEARING LIFE BY UP TO 300% 

THE ALITHICON “FLEET” SYNTHETIC ENCLOSED GEAR AND TRANSMISSION 

OILS ARE AVAILABLE IN 3 DIFFERENT S.A.E. GRADES, AS LISTED. 

ALITHICON 5000 “FLEET SYNTHETIC ENCLOSED GEAR LUBRICANT (S.A.E. -50) 

FOR MANUAL TRUCK TRANSMISSION, REQUIRING A NON-DETERGENT, NON-E.P., S.A.E.-50, GL- 

1 LUBRICANT. 

MEETS AND EXCEEDS THE FOLLOWING MANUFACTUERS’ REQUIREMENTS: EATON 

TRANSMISSION DIVISION PS-164, ROCKWELL INTERNATIONAL 0-80, AND THE 750,000-MILE 

WARRANTY COVERAGE FOR EATON AND ROCKWELL TRANSMISSIONS. 

FOR ADDITIONAL INFORMATION SEE REVERSE SIDE OF THIS BROCHURE

ALITHICON 7590 “FLEET” SYNTHETIC ENCLOSED GEAR AND TRANSMISSION LUBRICANT, S.A.E.-75/w90, 

GL-5. 

ALITHICON 4585 “FLEET” SYNTHETIC ENCLOSED GEAR AND TRANSMISSION LUBRICANT, S.A.E. 85/w140, 

GL-5. 

FOR MANUAL TRANSMISSIONS AND FINAL DRIVES REQUIRING A S.A.E.-75w/90 OR S.A.E. 85w/140, GL-5 

LUBRICANT. 

MEETS AND EXCEEDS THE FOLLOWING MANUFACTUERS’ REQUIREMENTS: U.S. MILITARY 

SPECIFICATIONS: MIL-L-2105D & MIL-PRF-2105E, A.P.I. SERVICE CLASSIFICATION GL-5, EATON AXLE 

DIVISION PS-163 & PS-109, GENERAL ELECTRIV D-50E9C, HARNISHFEGER (P&H) 474, MACK GO-H/S, MACK 

GO-J, SPICER AXLE DIVISION, DANA CORP, ROCKWELL INTERNATIONAL O-76-B AND ROCKWELL & EATON 

750,000-MILE WARRANTY COVERAGE. 

THE ALITHICON “FLEET” SYNTHETIC ENCLOSED GEAR LUBRICANT STOPS LEAKS IN OIL-FILLED WHEEL 

BEARINGS. 

IT ALSO STOPS 95% OF THE LEAKS FOUND IN TRUCK DIFFERENTIALS, TRAILER WHEEL BEARINGS, 

ROTARY MOVER GEAR BOXES, READY-MIX CONCRETE TRUCK DRUM GEAR REDUCERS, WATER WELL 

DRILLING TURN TABLES, AND MUD PUMPS. 

ALITHICON “FLEET” SYNTHETIC ENCLOSED GEAR AND TRANSMISSION LUBRICANTS 

TYPICAL TEST RESULTS 

TEST-TYPE ASTM CODE < - - - - - - - - - RESULTS - - - - - - - - - - - > 

ALITHICON PRODUCT CODE ASTM CODE 5000 7590 4585 

S.A.E. GRADE XXX 50 75/w/90 85w/140 

A.P.I. CLASSIFICATION XXX GL-1 GL-5 GL-5 

A.G.M.A. GRADE XXX 4 4 5/6 

COLOR XXX BRONZE BRONZE BRONZE 

TEXTURE XXX SMOOTH/ SMOOTH/ SMOOTH/ 

GRAVITY, A.P.I. D-4052 23 25.2 22.3 

FLASH POINT, °F D-92 461 463 487 

VISCOSITY 

CST @ 40°C 

D-445 137 

18.3 

129 

17.4 

274 

31.0 

VISCOSITY INDEX D-2270 162 162 162 

POUR POINT, °F D-97 -21 -21 -21 

CHANNEL POINT, MAX, °F XXX -61 -56 -56 

COPPER STRIP CORROSION XXX PASS PASS PASS 

TIMKEN O.K. LOAD, lbs, MIN D-2509 100 100 100 

* * * NOTE: LISTED ARE TYPICAL TEST RESULTS. * * * ON-SITE TEST RESULTS MAY PRODUCE A LIGHT VARIANCE. 

AVAILABLE PACKAGING: 

45 lb. (6 GALLON) PAIL 120 lb. (16 GALLON) KEG 

420 lb. (55 GALLON) DRUM 2,100 lb. (GALLON) DISPOSABLE TOTE

ALITHICON E.P. PARA/SYNTHETIC 

ENCLOSED GEAR LUBRICANTS 

THE ALITHICON E.P. PARA/SYNTHETIC ENCLOSED GEAR LUBRICANTS OFFER A COMPLETE 

LINE, OR A SELECTION OF, LONG-LIFE, EXTREME-PRESSURE GEAR OILS, FORMULATED TO 

LUBRICATE ALL AUTOMOTIVE AND INDUSTRIAL GEAR DRIVES. 

BEING A BLEND OF A HIGH QUALITY HYDRO-CRACKED, AND A FULL SYNTHETIC BASE, FLUIDS, 

IT IS NOT NECESSARY TO ADD VISCOSITY INDEX IMPROVERS. THE ALITHICON E.P. 

PARA/SYNTHETIC ENCLOSED GEAR LUBRICANTS NATURALLY POSSESSES A STRONG 

LUBRICANT FILM, WHICH RESISTS RUPTURE, WHEN SUBJECTED TO EXTREME PRESSURES, 

REDUCING OPERATING TEMPERATURES, WHILE GREATLY EXTENDING GEAR AND BEARING 

LIFE. 

THE ALITHICON E.P. PARA/SYNTHETIC ENCLOSED GEAR LUBRICANTS NOT ONLY MEET, BUT 

EXCEED THE MILITARY SPECIFICATIONS: MIL-L-2105D AND MIL-PRF-2105E, AS WELL AS, MACK 

TRUCKS GO-J, EATON AXLE DIVISION PS-037, GENERAL ELECTRIC D50E9C, U.S. STEEL 224, 

AGMA-250.04, ROCKWELL-STANDARD 076-A AND 076-D. ALSO FOR MANUAL TRANSMISSIONS 

AND AXLES MANUFACTURED BY CLARK, EATON, FULLER, INTERNATIONAL HARVESTER, 

SPICER, AND BORG-WARNER. 

THEY ARE RECOMMENDED TO LUBRICATE GEAR DRIVES WHICH REQUIRE THE API SERVICE 

CLASSIFICATIONS GL-4 AND GL-5, AND THEY ARE FORMULATED TO BE COMPATIBLE WITH, OR 

FAVORABLY MIX WITH OTHER HYDROCARBON ENCLOSED GEAR OILS. 

THE ALITHICON E.P. PARA/SYNTHETIC ENCLOSED GEAR LUBRICANTS ARE COMPATIBLE WITH 

ESSENTIALLY ALL ELASTOMERS, GASKETS, SEALS, SUCH AS: NITRITE, BUNA N, VITON, 

TEFLON, POLYETHYLENE, FLOUROCARBON, POLYACRYLATE, EPOXY AND PVC. THEY WILL NOT 

DETERIORATE ACRYLIC PAINTS OR LACQUERS. 


* REDUCES OPERATING TEMPERATURES 

* WILL NOT FOAM IN SERVICE 

* WILL NOT MIX WITH WATER 

* REDUCES SEAL SEEPAGE, AS MUCH AS 80% 

* TIMKEN O.K. LOAD RATING, 80 lbs., MIN. 

* EXPECT, LONGER DRAIN INTERVALS 

* EXTEND GEAR AND BEARING LIFE, AS MUCH AS 300% 

ALITHICON LUBRICANTS CO., INC / P O BOX 5225 / ALBANY, GEORGIA 31706 

PHONE: 229-883-9515 / FAX: 229-883-9516 

E-MAIL: ALITHICON@ALITHICON.COM / WEBSITE: WWW.ALITHICON.COM

ALITHICON E.P. PARA/SYNTHETIC ENCLOSED GEAR LUBRICANTS 

TYPICAL TEST RESULTS 

PRODUCT I.D. CODE 680 689 690 675 656 614 625 

SAE VISCOSITY GRADE 80 EP 80w/90 EP 90 EP 75w/140 EP 85w/140 EP 140 EP 250 EP 

ISO GRADE 100 EP 55 EP 220 EP 24 EP 90 EP 460 EP 1000 EP 

AGMA GRADE 3 EP 4 EP 5 EP 6 EP 6 EP 7 EP 8 EP 

GRAVITY, ° API (ASTM D-92) 28.9 29.0 28.2 29.9 28.8 26.7 21.1 

FLASH POINT COC, ° F. (° C.) (ASTM D-92) 496 478 492 494 492 499 193 

POUR POINT, ° F. (° C.) (ASTM D-97) +3 (-16) +3 (-16) +3 (-16) +3 (-16) +3 (-16) +3 (-16) +15 (-9) 

TIMKEN O.K. LOAD, lbs., MIN. (ASTM D-2509) > 85 > 85 > 85 > 85 > 85 > 85 > 85 

VISCOSITY INDEX (ASTM D-2270) 122 122 122 122 122 122 122 

VISCOSITY (ASTMD-445) 

cSt @ 40° C. 

cSt @ 100° C. 

VISCOSITY (ASTMD-2161) 

cSt @ 100° F. 

cSt @ 210° F. 

100 

11 

475 

62 

55 

7 

286 

51 

220 

18 

996 

88 

24 

4.6 

137 

43 

90 

10 

430 

59 

460 

31 

2259 

178 

1000 

55 

4922 

262 

FOUR-BALL WEAR, mm @ 20 kg (ASTM 2266) 31.0 31.2 31.6 31.0 32.2 32.1 32.4 

FOUR-BALL E.P. TEST, WELD, kg (ASTM D-2596) 262 262 266 263 262 265 262 

FOAM TEST, SEG III (ASTM D-892) 0 / 0 0 / 0 0 / 0 0 / 0 0 / 0 0 / 0 0 / 0 

CORROSION, 3 hrs @ 212° F. (ASTM D-130) 1A 1A 1A 1A 1A 1A 1A 

RUST TEST (ASTM D-665 A&B) PASS PASS PASS PASS PASS PASS PASS 

DEMULSIBILITY (ASTM D-2711-B) 

WATER IN OIL, % MAX. 

TOTAL FREE WATER, ml, MIN. 

EMULSION, ml, MAX. 

.5 

12 

.5 

.5 

12 

.5 

.5 

13 

.5 

.5 

11 

.5 

.5 

12 

.5 

.5 

12 

.5 

.5 

14 

.5 

POUNDS PER GALLON 7.34 7.32 7.37 7.23 7.33 7.40 7.42 

COLOR RED RED RED RED RED RED RED 


* 45 lb (6 GALLON) PAIL * 120 lb (16 GALLON) KEG * 420 lb (55 GALLON) DRUM * 2,500 lb (330 GALLON) DISPOSABLE TOTE * BULK 


PHONE: 229-883-9515 / FAX: 229-883-9516 


SGO ALITHICON SYNTHETIC 

ENCLOSED GEAR LUBRICANT 

THE SGO ALITHICON ENCLOSED GEAR LUBRICANT IS A HEAVY-DUTY LUBRICANT, DESIGNED 

FOR INDUSTRIAL AND AUTOMOTIVE USE. 

THE SGO ALITHICON SYNTHETIC GEAR LUBRICANT IS COMPOUNDED OF A SYNTHETIC BASE 

MATERIAL AND THE LATEST ADDITIVE CHEMICALS WHICH ARE SPECIFICALLY BALANCED FOR 

USE WITH THESE SYNTHETIC BASE STOCKS. THUS, IT PERFORMS VERY EFFECTIVELY WHERE 

TYPICAL PETROLEUM PRODUCTS AND OTHER SYNTHETIC GEAR LUBRICANTS FAIL. 

THE ALITHICON EXTREME PRESSURE PROPERTIES EXCEED THOSE OF ANY OTHER PRODUCT 

THAT IS AVAILABLE TODAY. THE COMBINATION OF SYNTHETIC BASE MATERIALS AND 

EFFECTIVE COKING AND OTHER DAMAGING DEPOSITS. 

THE SGO ALITHICON GEAR LUBRICANT HAS EXCELLENT HIGH AND LOW TEMPERATURE 

PERFORMANCE AND THE USER CAN EXPECT LONGER DRAIN INTERVALS AND EXTENDED GEAR 

AND BEARING LIFE. 


* WILL NOT FOAM IN SERVICE * WILL NOT MIX WITH WATER 

* REDUCES OPERATING TEMPERATURES, GEAR REDUCERS RUN COOLER WITH SGO 

* LONGER DRAIN INTERVALS, OF UP TO 500% GREATER THAN PETROLEUM OILS 

* O.K. TIMKEN LOAD OF 100 lbs., MIN., OVER DOUBLE THE WEAR PROTECTION OF MOST GEAR 

LUBRICANTS ON THE MARKET 

* EXTENDS GEAR AND BEARING LIFE OF UP TO 300%, OVER MOST GEAR LUBRICANTS ON THE 

MARKET TODAY 

APPLICATIONS: INDUSTRIAL GEAR REDUCERS, AUTOMOTIVE GEAR REDUCERS, OIL TYPE 

WHEEL BEARINGS, BALL MILL / BOWL MILL GEAR DRIVES, COOLING TOWER GEAR REDUCERS, 

STOCK PUMP BEARINGS, CONTINUANCE CASTING PLANETARY REDUCERS, BROKE PIT PULPER 

REDUCERS, AERATOR GEAR DRIVES, VAN DER GRAAF HEAD ROLLER DRUM MOTOR GEAR 

REDUCERS, CALANDER ROLL GEAR BOXES, ETC. 

AVAILABLE GRADES: 

SGO 68 - (ISO 68) - 2 EP 

SGO 100 - (ISO 100) - 3 EP 

SGO 150 - (ISO 150) - 4 EP 

SGO 220 - (ISO 220) - 5 EP 

SGO 320 - (ISO 320) - 6 EP 

SGO 460 - (ISO 460) - 7 EP 

SGO 680 - (ISO 680) - 8 EP 

THE SGO ALITHICON LUBRICANTS WILL NOT CAUSE PITTING OR 

CORROSION TO BRASS OR BRONZE GEARING. 

THE SGO ALITHICON LUBRICANTS WILL MIX WITH PETROLEUM 

OILS, A SAFEGUARD IN CASE MISAPPLICATION OCCURS 

FOR TYPICAL SPECIFICATIONS AND TEST RESULTS, 

SEE REVERSE SIDE 


PHONE: 229-883-9515 / FAX: 229-883-9516 


SGO ALITHICON SYNTHETIC 

ENCLOSED GEAR LUBRICANT 

TYPICAL SPECIFICATIONS AND TEST RESULTS 

PRODUCT CODE 

SGO 

68 

SGO 

100 

SGO 

150 

SGO 

220 

SGO 

320 

SGO 

460 

ISO GRADE 68 100 150 220 320 460 680 

SAE VISCOSITY GRADE 20 30 40 90 90 140 140 

AGMA LUBRICANT NUMBER 2 EP 3 EP 4 EP 5 EP 6 EP 7 EP 8 EP 

FLASH POINT, ° F. 520 450 470 480 495 520 535 

POUR POINT, ° F. -60 -35 -30 -23 -20 -17 -16 

VISCOSITY @ 40° C., EST. 73 100 150 220 320 460 680 

VISCOSITY @ 100° C., EST. 8.8 11 14.8 18.4 24.1 31 38.2 

VISCOSITY INDEX, MIN. 125 125 125 1251 125 125 125 

TIMKEN O.K. LOAD IN lbs., MIN. 100 100 100 100 100 100 100 

4 BALL, WEAR, mm (ASTM - 226) 

40 kg / 1200 RPM, 75° C., 1 HOUR 

20 kg / 1800 RPM, 54° C., 1 HOUR 

THERMAL OXIDATION STABILITY 

OXIDATION @ 95° C., 312 HOURS 

(ASTM - 2893) VISC. INCR. % MAX. 

OXIDATION @ 121° C., 312 HOURS 

(ASTM - D-91) VISC. INCR. % MAX. 

0.372 

0.27 

1.15 

3.28 

0.37 

0.27 

1.15 

3.27 

0.38 

0.27 

0.40 

0.29 

0.37 

0.24 

0.36 

0.24 

SGO 

680 

ISO CLEANLINESS CODE RATING 

(DIS 4406) 14 / 11 14 / 11 14 / 14 / 11 14 / 11 14 / 11 14 / 11 

NAS 1638 CLEANLINESS CODE 

RATING 5 5 5 5 5 5 5 

SAE - J1165 CLEANLINESS CODE 

RATING 

1.1 

3.18 

1 

3.1 

.9 

1 

.85 

2.79 

0.36 

0.24 

.85 

2.79 

NOTE: THE ALITHICON SGO-220 SYNTHETIC ENCLOSED GEAR LUBRICANT (EP GL-5) 

MEETS AND EXCEEDS THE FOLLOWING MILITARY SPECIFICATIONS: 

MIL-L-2105C *** MIL-L-2105D *** PRF-2105E 


* 6 - 7.5 lb CANS CASE * 120 lb KEG 

* 45 lb PAIL * 420 lb DRUMS 

* BULK 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON FM 

FOOD MACHINERY GEAR OIL 

THE ALITHICON FOOD MACHINERY GEAR OILS ARE DESIGNED SPECIFICALLY TO LUBRICATE THE GEAR REDUCERS 

OF FOOD PROCESSING EQUIPMENT. THESE OILS MEET AND EXCEED F.D.A. REGULATION 21 CFR 178.35701 FOR 

LUBRICANTS HAVING INCIDENTAL CONTACT WITH FOOD, AND HAVE ALSO BEEN APPROVED AS H-1 LUBRICANTS 

FOR USE IN FOOD PLANTS UNDER THE JURISDICTION OF THE U.S.D.A. 

THE ALITHICON FOOD MACHINERY GEAR OILS ARE A REMARKABLE VARIETY OF LUBRICANTS FORMULATED FOR 

APPLICATIONS WHERE SUPERIOR PERFORMANCE IS REQUIRED, BUT WHERE PURITY IS OF THE UTMOST 

IMPORTANCE. 

THE ALITHICON FOOD MACHINERY GEAR OIL WILL NOT CREATE A PROBLEM WITH PLANT OR ANIMAL LIFE BY 

DAMAGING THE FOOD CHAIN, WHICH IS A CONCERN WHEN USING AN ENCLOSED GEAR LUBRICANT TO LUBRICATE 

GEAR DRIVES FOUND IN HYDRO LOCKS AND DAMS, AND MARINE EQUIPMENT. 


* WILL NOT MIX WITH WATER, MAKING IT POSSIBLE TO GREATLY EXTEND DRAIN INTERVALS, 

REDUCING LUBRICANT COSTS, AND REDUCING THE EXCESSIVE COSTS FOR THE 

DISPOSAL OF LARGE AMOUNTS OF USED OIL. 

* MEETS THE REQUIREMENTS OF THE USDA FOR THE CLASSIFICATION OF H-1 

(LUBRICANTS HAVING INCIDENTAL CONTACT WITH FOOD). 

* EXHIBITS EXCELLENT LOAD CARRYING AND ANTI-WEAR CHARACTERISTICS. 

* NON-FOAMING IN SERVICE. 

* CONTAINS AN FDA / USDA APPROVED BROAD SPECTRUM BIOCIDE, ELIMINATING THE POSSIBILITY OF 

MAINTAINING AND TRANSFERRING BACTERIA, FUNGUS, OR OTHER 

MICROBIAL ORGANISMS. 

* PROTECTS AGAINST RUST IN ENCLOSED GEAR REDUCERS. 

* RATES AN O.K. TIMKEN LOAD OF 70 lbs MIN. 

* EXTENDS GEAR AND BEARING LIFE BY 300%. 

THERE IS NO NEED TO SACRIFICE THE PERFORMANCE OF YOUR FOOD-PROCESSING 

MACHINERY, JUST TO MEET WITH USDA/FDA REQUIREMENTS, WHEN YOU HAVE THE ALITHICON FM 

FOOD MACHINERY ENCLOSED GEAR LUBRICANTS. 

APPLICATIONS: 

FOOD PROCESSING AMD PACAKAGING MACHINERY ENCLOSED GEAR DRIVES, HYDRO LOCK & AND DAM 

GEAR REDUCERS, POTABLE WATER PLANT GEAR DRIVES, EXPELLER GEAR DRIVES, ETC. 

PLEASE SEE REVERSE SIDE FOR TECHNICAL SPECIFICATIONS 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON FM FOOD MACHINERY GEAR OIL 

PRODUCT CODE 

TYPICAL SPECIFICATIONS: 

ASTM 

TEST 

METHOD 

FM-G70 FM-G90 FM-G140 

SAE VISCOSITY 80 90 140 

COLOR LIGHT BLUE LIGHT BLUE LIGHT BLUE 

GRAVITY, ° API D-287 30.7 29.8 29.3 

FLASH POINT, COC ° F D-92 422 397 331 

POUR POINT, ° F D-97 8 8 6 

VISCOSITY - est @ 40° C D-445 100 220 460 

EMULSION 

CHARACTERISITICS 

(OIL - WATER - 

EMULSION) ml 

D-401 0 0 0 

RUST TEST D-665 PASS 

(NO RUST) 

OXIDATION STABILITY, 

HOURS 

FOUR BALL WEAK, mm 

SCAR 

→ 20 kg LOAD 

→ 40 kg LOAD 

TIMKEN O.K. LOAD, lbs 

MIN. 

PASS 

(NO RUST) 

PASS 

(NO RUST) 

D-943 2,500 2,843 2,997 

D-226 

0.12 

0.16 

0.11 

0.15 

0.10 

0.13 

D-2782 70 70 70 

VISCOSITY INDEX, MIN. D-2270 110 110 110 

ISO CLEANLINESS DIS-4406 10 / 8 10 / 8 10 / 8 


* 6 / 1 gal CASE * 45 lbs (6 gal) PAIL * 420 lbs (55 gal) DRUMS 

* 330 gal NON-RETURNABLE (DISPOSABLE) TOTES * BULK 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON 7900 PARA/SYNTHETIC POWER FLUID 

(ISO 32 / 46 / 68) (SAE 10 / 20) 

THE ALITHICON 7900 PARA/SYNTHETIC POWER FLUID IS THE NEXT GENERATION OR, 

LATEST GENERATION ATF (AUTOMATIC TRANSMISSIONS FLUID) AND HYDRAULIC FLUID. 

IT IS RECOMMENDED TO LUBRICATE ALL COMMERCIAL ON-HIGHWAY AUTOMATIC 

TRANSMISSIONS AND OFF-HIGHWAY INDUSTRIES, INCLUDING AGRICULTURE, CONSTRUCTION, 

LOGGINGM FARMING, AND QUARRYING EQUIPMENT, REQUIRING A TYPE-A (SUFFIX A), 

DEXTRON AND TYPE-F FLUIDS. IT IS ALSO RECOMMENDED AS A REPLACEMENT FOR THE 

CATERPILLAR TO-4 (SAE 10) AND TO-4 (SAE 30) FLUIDS, AS WELL AS ALL HYDRAULIC SYSTEMS. 

THE USER OF THE ALITHICON 7900 PARA/SYNTHETIC FLUID CAN EXPECT THE FOLLOWING 

BENEFITS: 

* WILL NOT MIX WITH WATER 

* GREATLY REDUCES OPERATING TEMPERATURES 

* REDUCES HYDRAULIC LEAKS AND BLOWN HOSES AS MUCH AS 80% 

* EXTENDS TRANSMISSIONS, HYDRAULIC PUMP AND MOTOR LIFE 

* REDUCES FUEL CONSUMPTION WHEN USED TO LUBRICATE AUTOMATIC TRANSMISSIONS 

* WILL NOT FOAM IN SERVICE 

* EXTENDED DRAIN INTERVALS 

APPLICATIONS: 

ALL AUTOMATIC TRANSMISSIONS, DIFFERENTIALS, FINAL DRIVES, ALL HYDRAULIC SYSTEMS, 

POWER STEERING SYSTEMS, WET BRAKES, PTO’S, HYDROSTATIC DRIVES AND GEAR DRIVES 

REQUIRING AN API GL-4 OR SAE 80w GRADE GEAR OIL. 

- - - - - - 

THE ALITHICON 7900 PARA/SYNTHETIC FLUID MEETS AND EXCEEDS THE FOLLOWING 

INDUSTRY SPECIFICATIONS: 

GENERAL MOTORS DEXTRON III *** CHRYSLER MS-7176 E *** ALLISON C-4 

FORD TYPE-F AND MERCON FLUIDS *** JOHN DEERE J20C *** CATERPILLAR TO-2 

J.I. CASE MS 1204 / 1205 / 1206 / 1207 / 1209 *** DENISON HF-0, HF-1, HF-2 

VICKERS 35VQ25 *** MASSEY FERGUSON MF 1135 & 1141 

VOLVO WB-101 / BM *** KUBOTA UDT 


PHONE: 229-883-9515 / FAX: 229-883-9516 


COLOR 

ALITHICON 7900 PARA/SYNTHETIC POWER FLUID 


SPECIFICATION 

TEST RESULTS 

ISO GRADE (FOR USE) 32 / 46 / 68 

SAE GRADE (FOR USE) 10 / 20 

BASE OIL VISCOSITY (ASTM D-445) 

Cst @ 40° C. 

Cst @ 100° C. 

Sus @ 100° F. 

Sus @ 210° F. 

RED 

32.8 

5.86 

168.4 

45.9 

VISCOSITY INDEX (ASTM D-2270) 199 

POUR POINT (ASTM D-97) - 55 

FLASH POINT (ASTM D-92) 

@ ° C. 

@ ° F. 

GRAVITY, A.P.I. (ASTM D-287) 31.4 

WATER SEPERABILITY (ASTM D-1401) 

TIME TO 40/37/3 @ 82° C., MINUTES 1.6 

TIMKEN O.K. LOAD: lbs., MINUMUM (ASTM D-2782) 85 

RUST PROTECTION (ASTM D-665) 

289 

572 

PASS / NO RUST 

FOAM TEST (ASTM D-892) TENDENCY / STABILITY, ml/ml 0 / 0 

TOTAL ACID NUMBER (ASTM D-664) 0.23 

ISO CLEANLINESS LEVEL 14 / 13 / 11 

COPPER CORROSION TEST (ASTM D-130) 

3 hrs @ 210° F. 

250 hrs @ 210° F. 

DRY AIR OXIDATION LIFE TEST, 312 hrs @ 203° F. (ASTM 2893) 

% VISCOSITY INCREASE 

PRECIP. # (% SOLIDS) 

1A 

1A 

0 

0 

* NOTE #1 

ALITHICON, FOR USE PERFORMANCE AND BENEFITS, RECOMMENDS THE USE OF THE ALITHICON 7900 

PARA/SYNTHETIC POWER FLUID, AS A REPLACEMENT OF THE CATERPILLAR TO-4 (SAE-10 AND SAE-30) FLUIDS. 

MANUFACTURER’S WARRANTY REQUIREMENTS MAY BE QUESTIONED, DUE TO THE VARIATION OF USED BASE 

FLUIDS AND CHOSEN ADDITIVE USE, OF THIS LUBRICANT, IN THESE APPLICATIONS. A DECISION TO USE THIS 

FLUID IN THE ABOVE-MENTIONED APPLICATIOND IS WITH THE USERS’ UNDERSTANDING. 

** NOTE #2 

THE ALITHICON 7900 PARA/SYNTHETIC POWER FLUID’S SOLVENCY CLEANS WEAR METALS AND DEPOSITS, 

WHICH CAN BECOME SOLUBLE IN THE NEW ALITHICON 7900 FLUID, CAUSING ABNORMALLY HIGH VALUES IN 

USED OIL ANALYSIS, UNTIL THE EQUIPMENT IS CLEAN. 

AVAILABALE PACKAGING: 

* 6 GALLON PAILS * 55 GALLON STEEL DRUMS 

* 220 GALLON DISPOSIBLE TOTES * BULK

ALITHICON PARA/SYNTHETIC TURBINE OILS 

THE ALITHICON PARA/SYNTHETIC TURBINE OILS ARE DESIGNED FOR USE IN STEAM-TURBO 

GENERATORS, SMALLER TURBINES, GEAR REDUCERS CALLING FOR A NON - E.P. (EXTREME PRESSURE) 

LUBRICANT, BEARINGS, HYDRAULIC SYSTEMS, CIRCULATING SYSTEMS, AND AIR COMPRESSORS. 

THE ALITHICON PARA/SYNTHETIC TURBINE OILS WILL NOT FOAM, WILL NOT MIX WITH WATER, 

PREVENTS CORROSION AND WEAR, AND IS EXTREMELY LONG-LASTING IN SERVICE. 

FORTIFIED WITH A HIGHLY EFFECTIVE ANTI-WEAR PACKAGE, THE ALITHICON PARA/SYNTHETIC TURBINE 

OIL PROVIDES MAXIMUM PROTECTION AND COMPATIBILITY WITH STEEL AND COPPER SURFACES. 

HIGH VISCOSITY INDEX BASE OILS, WITH POUR POINT DEPRESSANTS, ENSURE A BROAD TEMPERATURE 

RANGE PERFORMANCE. 

IN REFERENCE TO THE ALITHICON PARA/SYNTHETIC TURBINE OIL'S EXTREMELY LONG SERVICE LIFE, IT 

HAS BEEN CLASSIFIED AS "ENVIRONMENTALLY FRIENDLY". 

THE ALITHICON PARA/SYNTHETIC TURBINE OILS MEET THE REQUIREMENTS OF ALL MAJOR EQUIPMENT 

MANUFACTURERS, INCLUDING ABEX-DENISON HF-0 AND HF-2; CINCINNATI MILACRON P-68, P-69, AND P- 

70; SPERRY VICKERS INDUSTRIAL AND MOBIL HYDRAULIC SYSTEMS; VICKERS 35VQ25 PUMP TEST. 

THEY ARE ALSO RECOMMENDED FOR USE IN GEAR REDUCERS WHERE AN API GL-1 THROUGH GL-3 

GEAR PROTECTION IS REQUIRED. 

APPLICATIONS: 

ROTARY VANE, SCREW, AND RECIPROCATING AIR COMPRESSORS, ENCLOSED PARALLEL SHAFT GEARS, 

ENCLOSED GEAR DRIVES, PLAIN AND ANTI-FRICTION BEARINGS, ELECTRIC MOTOR BEARINGS, MACHINE 

TOOLS, HYDRAULIC SYSTEMS, OIL MIST BEARING LUBRICATION SYSTEMS, ETC. 

AVAILABLE IN THE FOLLOWING GRADES: 

6510 ISO 32 SAE 10 

6515 ISO 46 SAE 20 

6520 ISO 68 SAE 20 

6530 ISO 100 SAE 30 

6540 ISO 150 SAE 40 

6550 ISO 220 SAE 50 

6560 ISO 320 AGMA 6 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON PARA/SYNTHETIC TURBINE OILS 

PRODUCT CODE 6510 6515 6520 6530 6540 6550 6560 

SAE GRADE 10 20 20 30 40 50 60 

ISO GRADE 32 46 68 100 150 220 320 

GRAVITY, ° F. A.P.I. 32.0 31.0 30.0 29.0 29.0 28.0 27.0 

FLASH POINT, C.O.C., ° F. 420 430 440 480 490 510 515 

VISCOSITY, S.U.S. @ 210° F. 44 48 55 64 78 96 119 

VISCOSITY, S.U.S. @ 100° F. 160 245 370 505 790 1220 1700 

VISCOSITY INDEX 121 121 121 121 121 121 121 

POUR POINT, ° F. MAX. -60 -60 -55 -55 -50 -50 

COLOR BLUE BLUE BLUE BLUE BLUE BLUE BLUE 

OXIDATION LIFE (ASTM D-943) 5,000 5,000 5,000 5,000 5,000 5,000 5,000 

ISO CLEANLINESS CODE RATING 

NAS 1638 CLEANLINESS CODE 

RATING 

SAE - J1165 CLEANLINESS CODE 

RATING 

PACKAGING: 

* 6 / 1 GALLON CASE * 6 GALLON PLASTIC PAIL * 55 GALLON DRUM 

* 330 GALLON NON-RETURNABLE TOTES * BULK 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON FM 

FOOD MACHINERY TURBINE OIL 

THE ALITHICON FM FOOD MACHINERY TURBINE OILS ARE FOOD GRADE LUBRICANTS, DESIGNED TO 

LUBRICATE FOOD PROCESSING EQUIPMENT, SUBMERGED WATER WELL PUMP BEARINGS, HYDRO DAM 

GEAR MECHANISMS, POTABLE WATER PLANT EQUIPMENT, ETC. THESE LUBRICANTS MEET AND EXCEED 

THE REQUIREMENTS OF U.S. FDA REGULATION 21 CFR 178.3570 FOR LUBRICANTS HAVING INCIDENTAL 

CONTACT WITH FOOD, AND HAVE ALSO BEEN APPROVED AS H-1 LUBRICANTS FOR USE IN FOOD PLANTS 

UNDER THE JURISDICTION OF THE USDA. 

THE ALITHICON FM FOOD MACHINERY TURBINE OILS ARE A REMARKABLE VARIETY OF LUBRICANTS 

FORMULATED FOR APPLICATIONS WHERE SUPERIOR PERFORMANCE IS REQUIRED, BUT WHERE PURITY 

IS OF THE UTMOST IMPORTANCE. BEING TOTALLY NON-TOXIC, THEY WILL NOT CREATE PROBLEMS 

WITH PLANT OR ANIMAL LIFE BY DAMAGING THE FOOD CHAIN. 

THE ALITHICON FM FOOD MACHINERY TURBINE OILS EXHIBIT EXCELLENT ANTI-WEAR AND NON- 

FOAMING CHARACTERISTICS. 

THE ALITHICON FM LUBRICANTS ARE SUPERIOR, LONG-LIFE, AND NON-STAINING, WHICH ARE 

EXCELLENT FOR USE TO LUBRICATE TEXTILE MACHINERY. 


* MEETS WITH THE USDA CLASSIFICATION OF H-1 

(LUBRICANTS HAVING INCIDENTAL CONTACT WITH FOOD) 

* EXHIBITS EXCELLENT ANTI-WEAR CAPABILITIES 

* ELIMINATES RUST * NON-FOAMING IN SERVICE * NON-STAINING 

* DESIGNED FOR HYDRAULIC SYSTEMS IN FOOD-PROCESSING PLANTS 

* EXCELLENT FOR USE TO LUBRICATE AIR COMPRESSORS IN FOOD-PROCESSING PLANTS 

CHECK THE ALITHICON LUBRICANT FOR USDA APPROVAL, FOR USE IN FOOD PROCESSING PLANTS IN 

THE 2002 NSF WHITE BOOK (NSF INTERNATIONAL / NON-FOOD COMPOUNDS) AT www.nsf.org/usda 

APPLICATIONS: 

* HYDRAULIC SYSTEMS * AIR COMPRESSORS * ROLLER CHAINS 

* HYDRO DAM EQUIPMENT * TEXTILE MACHINERY * POTABLE WATER PLANT EQUIPMENT 

* SUBMERGED WATER WELL PUMP BEARINGS 


* 24 / 1 QUART CASE * 6 GALLON PAIL 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON FM FOOD MACHINERY LUBRICANT 

TYPICAL SPECIFICATIONS AND TEST RESULTS: 

PRODUCT CODE FM-H10 FM-H22 FM-H27 FM-H30 FM-H50 

SAE GRADE 10 20 20 30 40 

COLOR WATER CLEAR WATER CLEAR WATER CLEAR WATER CLEAR WATER CLEAR 

SPECIFIC GRAVITY 0.925 0.912 0.95 0.951 0.87 

VISCOSITY: SUS @ 40° C 32 42.3 73 108 151 

VISCOSITY: SUS @ 210° C 44.6 50.6 51.4 60 72 

VISCOSITY INDEX 150 150 180 189 189 

POUR POINT: ° F -70 -57 -60 -60 -55 

FLASH POINT: ° F 460 530 520 515 515 

AUTO-IGNITION: ° F 760 760 760 760 765 

ACID NUMBER 0.2 0.2 0.2 0.2 0.2 

ROTARY BOMB OXIDATION 300° F 

LIFE MINUTES (ASTM D-2272) 

720 960 1235 1340 1545 

CENTRALIZED OXIDATION TEST 

230° F (ASTM D-943) MED. 

» HOURS TO INCREASE ACID # 0.2 

» HOURS TO INCREASE ACID # 2.0 

1360 

3375 

1360 

3375 

1360 

3375 

1360 

3375 

1360 

3375 

OXIDATION CORROSSION STABILITY (FTM 

5308.6) 72 HOURS @ 350° F: 

METAL WEIGHT (mg) 

» Cu, Mg, Fe, Al, Ag 

» EVAPORATIVE LOSS, WT. % 

22 HOURS @ 210° F 

» SLUDGE 

» TAN INCREASE Mg KOH / g 

± .03 

.02 

CLEAN 

1.0 

± .03 

.024 

CLEAN 

1.4 

± .03 

.03 

CLEAN 

1.0 

± .03 

.05 

CLEAN 

2.0 

± .03 

.55 

CLEAN 

2.1 

RUST PREVENTION 24 HOURS: 

DISTILLED WATER (ASTM D-665) NO RUST NO RUST NO RUST NO RUST NO RUST 

FOAM TENDENCY (ml) @ 15 mins 

(ASTM D-982) 

» 75° F 

» 200º F 

> 10 / 0 

> 5 / 0 

> 10 / 0 

> 5 / 0 

> 5 / 0 

> 5 / 0 

> 5 / 0 

> 5 / 0 

> 5 / 0 

> 5 / 0 

DEMULSIBILITY @ 130° F 

OIL/WATER/EMULSION, ml 

(ASTM D-1401) NO RUST NO RUST NO RUST NO RUST NO RUST 

CONRADSON CARBON RESIDUE 

WT, % (ASTM D-892) 

PANEL COKING, mg DEPOSIT: 

6 HOURS @ 600° F 9.8 9.2 9.1 6 7.3 

4 BALL, SCAR DM mm, (ASTM D-189) 

»10 kg @ 1800 RPM & 150° F FOR 30 MIN 

»40 kg @ 1200 RPM & 167° F FOR 60 MIN 

0.4 

0.4 

0.4 

0.4 

0.4 

0.4 

0.4 

0.4 

0.4 

0.4 

VICKERS PUMP TEXT @ 150° F 

TOTAL WEIGHT LOSS (ASTM D-2892) 25.0 18.1 10.3 10.0 9.9 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON 9700 PARA/SYNTHETIC 

INDUSTRIAL POWER FLUID 

THE ALITHICON 9700 PARA/SYNTHETIC INDUSTRIAL POWER FLUID IS FORMULATED FROM 

PREMIUM-QUALITY SYNTHETIC AND PETROLEUM BASE LUBRICANT FLUIDS, RESULTING IN A 

SUPERIOR MULTI-VISCOSITY LUBRICANT, DESIGNED FOR USE, TO BE USED IN HYDRAULIC 

SYSTEMS, VARIABLE SPEED DRIVES, PIV’S, FLUID-TYPE BEARING LUBRICANT, REEVES DRIVES, 

GEAR REDUCERS AND ROLLER CHAINS. 

THE ALITHICON 9700 PARA/SYNTHETIC INDUSTRIAL POWER FLUID IS A MULTI-VISCOSITY 

LUBRICANT DESIGNED, TO BE USED, TO LUBRICATE EQUIPMENT REQUIRING AN ISO-32, ISO-46, 

AND ISO-68 LUBRICANT, ELIMINATING THE NEED TO INVENTORY THREE OILS, WHILE 

MAINTAINING YOUR EQUIPMENT, WHILE GREATLY EXTENDING EQUIPMENT LIFE AND 

INCREASING PRODUCTION. 

WE ALSO, RECOMMEND TO USE THE ALITHICON 9700 PARA/SYNTHETIC INDUSTRIAL POWER 

FLUID IN APPLICATIONS WHERE OEM REQUIREMENTS CALL FOR AND ISO-100 FLUID. 

THE ALITHICON 9700 PARA/SYNTHETIC INDUSTRIAL POWER FLUID GREATLY REDUCES 

OPERATING TEMPERATURES AND WILL EXTEND THE LIFE OF VARIABLE-SPEED DRIVES OF UP 

TO 500% OVER THE MORE COMMONLY USED OILS. 


* WILL NOT MIX WITH WATER * WILL NOT FOAM IN SERVICE 

* REDUCES OPERATING TEMPERATURES * CONTROLS RUST AND CORROSION 

* RESISTS OXIDATION * ELIMINATES THE NEED TO INVENTORY TWO OILS 

* FORTIFIED WITH EXTREME PRESSURE (EP) ADDITIVES, WHICH HAS NO ADVERSE 

EFFECT ON ANY METALS 

* REDUCES 80% OF LEAKS AND BLOWN HOSES IN HYDRAULIC SYSTEMS 

* EXTENDED DRAIN INTERVALS, WHICH CAN CLASSIFY IT AS ENVIRONMENTALLY 

FRIENDLY 

* GREATLY EXTENDS VARIABLE SPEED AND BEARING LIFE OF UP TO 500% 

APPLICATIONS: 

HYDRAULIC SYSTEMS, OIL-LUBRICATED BEARINGS, VARIABLE SPEED DRIVES, REEVES DRIVES, 

ENCLOSED GEAR REDUCERS, PIV’S, ROLLER CHAINS, AND MANY MORE. 

FOR TYPICAL SPECIFICATIONS AND AVAILABLE PACKAGING, SEE REVERSE SIDE 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON 9700 PARA/SYNTHETIC 

INDUSTRIAL POWER FLUID 


COLOR 

SPECIFICATION 

TEST RESULTS 

BLUE 

ISO GRADE (FOR USE) 32 / 46 / 68 

SAE GRADE (FOR USE) 10 / 20 

BASE OIL VISCOSITY (ASTM D-445) 

Cst @ 40° C. 

Cst @ 100° C. 

Sus @ 100° F. 

Sus @ 210° F. 

32.8 

5.86 

168.4 

45.9 


POUR POINT (ASTM D-97) - 55 

FLASH POINT (ASTM D-92) 

@ ° C. 

@ ° F. 

GRAVITY, A.P.I. (ASTM D-287) 31.4 

WATER SEPARABILITY (ASTM D-1401) 

TIME TO 40/37/3 @ 82° C., MINUTES 

1.6 

TIMKEN O.K. LOAD: lbs., MINIMUM (ASTM D-2782) 95 

RUST PROTECTION (ASTM D-665) 

289 

572 

PASS / NO RUST 

FOAM TEST (ASTM D0892) TENDENCY / STABILITY, ml/ml 0 / 0 

TOTAL ACID NUMBER (ASTM D-664) 0.23 

ISO CLEANLINESS LEVEL 14 / 13 / 11 

COPPER CORROSION TEST (ATM D-130) 

3 hrs @ 210° F. 

250 hrs @ 210°F. 

DRY AIR OXIDATION LIFE TEST, 312 hrs @ 203°F. (ASTM 2893) 

% VISCOSITY INCREASE 0 

0 

1A 

1A 


* 6 / 1 gal CASE * 6 gal PAIL 

* 55 gal DRUM * 330 gal NON-RETURNABLE (DISPOSABLE) TOTE 

* BULK 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON 822 SYNTHETIC 

HIGH TEMPERATURE CHAIN LUBRICANT 

THE ALITHICON 822 SYNTHETIC HIGH TEMPERATURE CHAIN LUBRICANT IS FORMULATED TO PROVIDE 

EXTRA-LONG SERVICE LIFE IN HIGH TEMPERATURE APPLICATIONS. ITS PHYSICAL CHARACTERISTICS 

MAKE THE ALITHCON 822 THE IDEAL FLUID TO USE TO LUBRICATE BAKERY OVEN ROLLER CHAINS, 

WHICH MUST OPERATE UNDER EXTREME HIGH TEMPERATURES, ABOVE THOSE AT WHICH PETROLEUM 

OILS WILL NOT PERFORM SATISFACTORILY (ABOVE 400° F.). 

THE ALITHICON 822 SYNTHETIC HIGH TEMPERATURE CHAIN LUBRICANT IS HIGHLY RESISTANT TO 

THERMAL CRACKING, WHICH RESULTS IN THE FORMATION OF COKE. IT IS ALSO HIGHLY RESISTANT TO 

OXIDATION THICKENING. THE DISTILLATION POINT OF THE ALITHICON 822 ALLOWS CHAINS TO OPERATE 

AT MAXIMUM PERFORMANCE, WHEN CHAINS’ ENVIRONMENTS REACH TEMPERATURES OF, AS MUCH AS 

700° F. 

THE ALITHICON 822 SYNTHETIC HIGH TEMPERATURE CHAIN LUBRICANT IS FORMULATED FROM A 

TECHNICAL GRADE, SYNTHETIC WHITE OIL, WHICH MEETS WITH FDA / USDA REQUIREMENTS, FOR USE 

TO LUBRICATE CHAINS IN FEDERALLY INSPECTED MEAT AND POULTRY PLANTS. IT IS ALSO NON-TOXIC 

AND ENVIRONMENTALLY FRIENDLY. 

THE ALITHICON 822 SYNTHETIC HIGH TEMPERATURE CHAIN LUBRICANT IS ALSO AVAILABLE IN A NON- 

DRIP FORMULATION. WHEN ORDERING THE NON-DRIP 822 CHAIN LUBRICANT, ORDER ALITHICON 822-T. 

CHECK THE ALITHICON LUBRICANT FOR USDA APPROVAL, FOR USE IN FOOD-PROCESSING PLANTS IN THE 2002 NSF 

WHITE BOOK (NSF INTERNATIONAL / NON-FOOD COMPOUNDS) AT www.nsf.org/usda 


* FORMULATED TO LUBRICATE BAKERY OVEN ROLLER CHAINS WHICH OPERATE 

IN EXTREMELY HIGH TEMPERATURES, OF UP TO 700° F. 

* ELIMINATES COKING, AND A “SOOTY CARBON” BUILDUP ON OVEN CHAIN ROLLERS 

* LEAVES NO RESIDUE BUILDUP WHEN THE ALITHICON 822 VAPORS ARE INCINERATED 

THROUGH BAKERY CATALYTIC BEDS OR SFTER-BURNERS. 

* FORMULATED WITH A FDA/USDA H-1 APPROVED FLUID 

* WATERPROOF - ELIMINATES CHAIN RUSTING WHEN USED TO LUBRICATE ROLLER 

CHAINS IN POULTRY PLANTS 

* LOW VOLATILITY - REDUCED VAPORS AND SMOKE 

* ENVIRONMENTALLY FRIENDLY 

* EXTENDS ROLLER CHAIN LIFE OF UP TO 500% LONGER THAN PETROLEUM OILS, 

UNDER EXTREMELY HIGH TEMPERATURE CONDITIONS 

FOR TECHNICAL SPECIFICATIONS, SEE REVERSE SIDE 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON 822 SYNTHETIC 

HIGH TEMPERATURE CHAIN LUBRICANT 

PHYSICAL CHARACTERISTICS / RESULTS 

PRODUCT CODE 822 822-T 

BASE STOCK 

NF / USP GRADE 

WHITE MINERAL OIL 

NF / USP GRADE 

WHITE MINERAL OIL 

APPEARANCE 

BRIGHT, CLEAR, 

COLORLESS 

BRIGHT, CLEAR, 

COLORLESS 

ODOR NONE NONE 

TASTE NONE NONE 

VISCOSITY CENTISTOKES @ 40° C. (ASTM-D-445) 31 37 

POUR POINT, ° F (ASTM D-97) - 90 - 85 

FLASH POINT, COC, ° F. (ASTM D-92) 476 470 

DENSITY @ 60° F, g / ml (ASTM D-941) 0.83 0.83 

AUTOIGNITION TEMPERATURE ° F (ASTM D-2155) 708 708 

EVAPORATION LOSS, N² ATMOSPHERE 760 mm, 

6.5 hr. @ 400° F., WEIGHT % 4 4 

% EVAPORATION LOSS @ 600° F FOR 24 hrs 5 5 

% RESIDUE BUILD-UP @ 1,000° F 

UNTIL COMPLETE VOLATILIZATION 0 0 

THERMAL CONDUCTIVITY @ 300° F., 

BTU / hr ft² - ° F / ln 0.91 0.91 

SPECIFIC HEAT, BTU / lb - ° F 

200° F 

300° F 

400° F 

500° F 

600° F 

COEFFICIENT THERMAL EXPANSION @ 55° F. 0.0045 0.0045 

VAPOR P² @ 300° F (ASTM D-2897) 0.7 mm / hg 0.7 mm / hg 

VISCOSITY @ 210° F. 5.66 5.66 

SURFACE TENSION, dy / cm @ 6° F. (ASTM D-1331) 30 30 

0.48 

0.54 

0.59 

0.64 

0.70 

0.48 

0.54 

0.59 

0.64 

0.70 

** PROPERTIES ARE TYPICAL AND MAY VARY. 


* 6 / 1 GALLON CASE * 6 GALLON PAILS 

* 55 GALLON DRUMS * BULK 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON DC-1300 

SYNTHETIC HIGH TEMPERATURE LUBRICANT 

THE ALITHICON DC-1300 SYNTHETIC HIGH TEMPERATURE LUBRICANT IS A FLUID LUBRICANT, 

DESIGNED TO SUCCESSFULLY PROVIDE PROTECTION AND REDUCE WEAR FOR CHAINS, 

BEARINGS, AND JOURNALS WHICH MUST OPERATE UNDER HEAVY LOADS, IN THE PRESENCE 

OF WATER OR STEAM AND IN EXTREMELY HIGH TEMPERATURES. 

THE ALITHICON DC-1300 SYNTHETIC HIGH TEMPERATURE LUBRICANT IS DESIGNED TO 

GREATLY REDUCE WEAR, WHILE OPERATING UNDER HEAVY LOADS WITH AN O.K. TIMKEN 

LOAD RATING OF120 lbs., MIN. 

THE ALITHICON DC-1300 SYNTHETIC HIGH TEMPERATURE LUBRICANT IS WATERPROOF AND 

STEAMPROOF. IT ADHERES TO DRY METAL SURFACES AND REFUSES TO RELEASE UNDER 

WET WORKING ENVIRONMENTS. 

THE ALITHICON DC-1300 SYNTHETIC HIGH TEMPERATURE LUBRICANT IS FORMULATED TO 

REDUCE WEAR AND PROTECT ROLLER CHAINS WHICH MUST OPERATE IN EXTREMELY HIGH 

TEMPERATURES. THE ALITHICON DC-1300 LUBRICANT WILL WITHSTAND OPERATING 

TEMPERATURES OF UP TO 1300° F. 

THE ALITHICON DC-1300 SYNTHETIC HIGH TEMPERATURE LUBRICANT IS DESIGNED FOR USE 

IN ANY CENTRALIZED LUBRICATING SYSTEM WHICH CAN DISBURSE THE SIZE OF .05 MICRONS 

OR LESS. 

THE ALITHICON DC-1300 SYNTHETIC HIGH TEMPERATURE LUBRICANT IS AVAILABLE IN THREE 

ISO GRADES. 


* WITHSTANDS TEMPERATURES OF UP TO 1300° F. 

* WATERPROOF AND STEAMPROOF - RESISTS WASH-OFF 

* EASILY APPLIED 

* RATES AN O.K. TIMKEN LOAD OD 120 lbs, MIN. 

* GREATLY EXTENDS CHAIN, BEARING, AND JOURNAL LIFE 

AVAILABLE GRADES: 

DC-1300-AAA (ISO-15) 

DC-1300-AA (ISO-100) 3 EP 

DC-1300-A (ISO-150) 4 EP 

DC-1300-B (ISO-220) 5 EP 

DC-1300-C (ISO-320) 5 EP 

APPLICATIONS: TENNER FRAME CHAINS, TEXTILE DRYER CHAINS, GYPSON OVEN CHAINS, 

PLYWOOD VENEER DRYER CHAINS, TEXTILE HOT OIL PRESS JOURNALS, ETC. 



PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON DC-1300 SYNTHETIC HIGH TEMPERATURE LUBRICANT 


PRODUCT CODE DC-1300-AAA DC-1300-AA DC-1300-A DC-1300-B DC-1300-C 

ISO GRADE 15 100 150 220 320 

SAE VISCOSITY GRADE 2 30 40 90 90 

AGMA LUBRICANT NUMBER N/A 3 EP 4 EP 5 EP 6 EP 

BASE FLUID FLASH POINT, ° F 520 490 490 485 505 

POUR POINT, ° F. - 40 - 30 - 30 - 20 - 20 

VISCOSITY @ 40° C, EST. 15 100 150 220 320 

VISCOSITY @ 100° C., EST. 3.4 10.7 17.24 19.7 29.3 

TIMKEN O.K. LOAD, lbs MIN. 135 120 120 120 120 

4 BALL WEAR, mm. (ASTM-226) 

40 kg/1200 rpm, 75° C, 1 HOUR 

20 kg/1800 rpm, 54° C, 1 HOUR 

0.121 

0.108 

0.149 

0.108 

0.149 

0.108 

0.16 

0.116 

0.148 

0.096 


* 6 / 1 GALLON CASE 

* 6 GALLON PAIL 

* 55 GALLON DRUM 

* BULK 


PHONE: 229-883-9515 / FAX: 229-883-9516 


700 ALITHICON 

SYNTHETIC HEAT TRANSFER FLUID 

THE 700 ALITHICON IS A SYNTHETIC HEAT TRANSFER FLUID, WHICH IS FORMULATED TO PROVIDE EXTRA 

LONG SERVICE LIFE IN HIGH TEMPERATURE SYSTEMS. ITS PHYSICAL CHARACTERISTICS MAKE THE 700 

ALITHICON THE IDEAL FLUID FOR USE IN HEAT TRANSFER SYSTEMS OPERATING IN TEMPERATURE 

RANGES ABOVE THOSE AT WHICH PETROLEUM OIL WILL NOT PERFORM SATISFACTORILY (ABOVE 400° F.). 

THE ALITHICON SYNTHETIC HEAT TRANSFER IS HIGHLY RESISTANT TO THERMAL CRACKING, WHICH 

RESULTS IN THE FORMATION OF COKE. IT IS ALSO HIGHLY RESISTANT TO OXIDATION THICKENING. THE 

DISTILLATION POINT OF THE 700 ALITHICON ALLOWS SYSTEM TEMPERATURES TO OPERATE AT MAXIMUM 

PERFORMANCE WHEN HEAT TRANSFER SYSTEMS REACH TEMPERATURES OF, AS MUCH AS, 700° F., WITH 

MINIMAL VAPOR PRESSURE. 

THE 700 ALITHICON SYNTHETIC HEAT TRANSFER FLUID IS FORMULATED FROM A TECHNICAL GRADE. 

SYNTHETIC WHITE OIL, WHICH MEETS FDA/USDA SPECIFICATIONS FOR USE TO LUBRICATE MACHINERY IN 

FEDERALLY INSPECTED MEAT AND POULTRY PLANTS. IT IS ALSO NON-TOXIC AND DUE TO A LONGER USE 

LIFE, BETWEEN FLUID CHANGES, IS CLASSIFIED AS, ENVIRONMENTALLY FRIENDLY. 

WHEN USING THE 700 ALITHICON SYNTHETIC HEAT TRANSFER FLUID, THE USER CAN EXPECT THE 

ELIMINATION OF “COKING” OR “SOOTY CARBON” BUILDUP WITHIN THE SYSTEM, AS I NORMALLY FOUND 

WHEN USING A NORMAL PETROLEUM OIL. DRAIN OR FLUID CHANGE INTERVALS CAN BE EXTENDED AS 

MUCH AS 600%. PERIODIC FLUID ANALYSIS IS RECOMMENDED WHEN EXTENDING DRAIN INTERVALS. 


FORMULATED FOR USE IN APPLICATIONS WHICH OPERATE IN SYSTEMS OF UP TO 700° F. 

ELIMINATES “COKING” AND “SOOTY CARBON” BUILD-UP WITHIN THE SYSTEM 

FORMULATED WITH FDA/USDA APPROVED TYPE FLUID 

EXCELLENT FOR USE IN FEDERALLY INSPECTED MEAT AND POULTRY PLANTS 

NON-CORROSIVE 

FULLY COMPATIBLE WITH COMMONLY USED SEAL MATERIALS 

LOW VOLATILITY - REDUCED VAPOR PRESSURE 

SUPERIOR THERMAL CONDUCTIVITY 

EXTENDED CHANGE / DRAIN INTERVALS OF UP TO 600% LONGER 

CLASSIFIED AS AN ENVIRONMENTALLY FRIENDLY FLUID, DUE TO EXTENDED DRAIN INTERVALS 

APPLICATIONS: 

FLUID FOR HEAT TRANSFER SYSTEMS 

FOR PACKAGING AND TECHNICAL SPECIFICATIONS, SEE REVERSE SIDE 


PHONE: 229-883-9515 / FAX: 229-883-9516 


700 ALITHICON SYNTHETIC HEAT TRANSFER FLUID 


PRODUCT CODE 700 

BASE FEED STOCK 

APPEARANCE 

ODOR 

TASTE 

NF/USP GRADE WHITE MINERAL 

BRIGHT, CLEAR, COLORLESS 

NONE 

NONE 

POUR POINT, ° F. (ASTM D-97) -90 

FLASH POINT, COC, ° F. (ASTM D-92) 470 

DENSITY @ 60° F., gr / ml (ASTM D-972) 0.83 

AUTOIGNITION TEMPERATURE (ASTM -2155) 

710° F 

EVAPORATION LOSS, N² ATMOSPHERE 

760 mm, 6.5 hrs @ 400° F, wt % (ASTM D-972) 4.0 

THERMAL CONDUCTIVITY @ 300° F., 

BTU / hr ft² - ° F / in .085 

SPECIFIED HEAT, BTU / lb - ° F. 

200° F. 

300° F. 

400° F. 

500° F. 

600° F. 

COEFFICIENT THERMAL EXPANSION @ 55° F. 0.0045 

VAPOR P² @ 300° F (ASTM D-2897) 

KINEMATIC VISCOSITY cst @ 40° C. (ASTM D-445) 

KINEMATIC VISCOSITY cst @ 100° C. (ASTM D-445) 

KINEMATIC VISCOSITY sus @ 100° F. (ASTM D-445) 

KINEMATIC VISCOSITY sus @ 210° F. (ASTM D-445) 

.48 

.54 

.59 

.64 

.70 

0.7 mm / hg 

29 

4.8 

149 

42 


SURFACE TENSION, dy / cm @ 68° F. (ASTMD-1331) 30 


* 6 / 1 gals CASE * 6 gal PAIL * 55 gal DRUM 

* 330 gal DISPOSABLE TOTE TANKS * BULK 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON FM-H27 PARA/SYNTHETIC 

CRACKER LUBRICANT 

THE ALITHICON FM-H27 PARA/SYNTHETIC CACKER LUBRICANT IS DESIGNED 

SEPCIFICALLY FOR NUT CRACKING MACHINERY, SUCH AS PECAN, WALNUT, BRAZIL 

NUTS, ETC., WHERE THERE IS A POSSIBILITY OF THE LUBRICANT AND EDIBLE NUT 

MEAT COMING IN CONTACT. 

THE ALITHICON FM-H27 LUBRICANT MEETS AND EXCEEDS THE REQUIREMENTS OF U.S. 

REGULATION 21 CFR 178.3570 FOR LUBRICANTS HAVING INCIDENTAL CONTACT WITH 

FOOD , AND HAVE ALSO BEEN APPROVED AS H-1, FR USE IN FOOD PLANTS UNDER THE 

JURISDICTION OF THE USDA. 

THE ALITHICON FM-H27 LUBRICANT IS FORMULATED FOR APPLICATION WHERE 

SUPERIOR PERFORMANCE IS REQUIRED, BUT WHERE PURITY IS OF THE UTMOST 

IMPORTANCE. 


* MEETS WITH THE USDA CLASSIFICATION OF H-1 

(LUBRICANTS HAVING INCIDENTAL CONTACT WITH FOOD) 

* EXHIBITS EXCELLENT ANTI-WEAR CAPABILITIES ON THE MOVING PARTS 

FOUND IN NUT-CRACKING MACHINERY 

* ELIMINATES RUST * NON-FOAMING IN SERVICE 

* EXTENDS MACHINERY LIFE OF UP TO 300% OVER THE MORE COMMONLY 

USED LUBRICANTS 

PACKAGING: 


* 6 / 1 GALLON CASE * 55 GALLON DRUM 

SEE REVERSE SIDE FOR TYPICAL SPECIFICATIONS 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON FM-H27 PARA/SYNTHETIC 

CRACKER LUBRICANT 

TYPICAL SPECIFICATIONS 

SAE VISCOSITY 

20 HEAVY 

GRAVITY, ° F., API 31.2 

FLASHPOINT, COC, ° F. 418 

POURPOINT, ° F. 17 

VISCOSITY, est @ 40° C. 68 

EMULSION CHARACTERISTICS 

(OIL - WATER - EMULSION) ml 

RUST TEST, 24 HOURS 

40 - 37 - 3 

(30 MINUTES) 

PASS - NO RUST 

OXIDATION STABILITY, HOURS 2,000 

FOUR BALL WEAR, mm SCAR 

» 20 kg LOAD 

» 40 kg LOAD 

0.26 

0.35 

VICKERS PUMP WEAR TEST 

WEIGHT LOSS (mg) 10 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON AL-32 PARA/SYNTHETIC 

AIR CYLINDER LUBRICANT 

THE ALITHICON AL-32 PARA/SYNTHETIC AIR CYLINDER LUBRICANT IS A SPECIAL BLEND 

OF PREMIUM QUALITY PETROLEUM AND SYNTHETIC FLUIDS, FORMULATED TO ENTRAP 

THE MOISTURE WHICH IS NORMALLY FOUND IN AIR SUPPLY LINES AND PROVIDE 

SUPERIOR LUBRICATION TO AIR CYLINDERS AND AIR OPERATED TOOLS. 

THE SLUDGE OR BUILD-UP NORMALLY FOUND IN AIR CYLINDERS AND AIR TOOLS, 

AFTER FAILURE, IS COMPLETELY ELIMINATED WHEN USING THE “ALITHICON AL-32”. 

GALLING, SCUFFING, AND EXCESSIVE WEAR ARE GREATLY REDUCED, TOO. 

THE USER OF THE “ALITHICON AL-32” PARA/SYNTHETIC AIR CYLINDER LUBRICANT CAN 

EXPECT 600% LONGER AIR CYLINDER AND AIR TOOL LIFE WHEN USED IN PLACE OF 

THE MORE COMMONLY USED OILS. 


* THE ELIMINATION OF SLUDGE OR BUILD-UP 

* EXCELLENT PROTECTION EVEN WHEN MOISTURE IS PRESENT 

* GREATLY REDUCES GALLING AND SCUFFING 

* GREATLY REDUCES AIR TOOL AND AIR CYLINDER WEAR 

* EXTENDS AIR TOOL AND AIR CYLINDER LIFE BY 600% 

PACKAGING: 


* 6 / 1 GALLON CASE * 55 GALLON DRUM 

SEE REVERSE SIDE FOR TYPICAL SPECIFICATIONS 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON “AL-32” PARA/SYNTHETIC 

AIR CYLINDER LUBRICANT 


ISO GRADE 32 

SAE GRADE 10 

VISCOSITY @ 40° C., c.S.t. 29.6 

VISCOSITY @ 100° C., c.S.t. 5.2 

VISCOSITY @ 100° F., c.S.t. 155.0 

VISCOSITY @ 210° F., c.S.t. 44.4 

VISCOSITY INDEX 125 

FLASH POINT, ° F. 445 

POUR POINT, ° F. -5 

GRAVITY, API 33.7 

SPECIFIC GRAVITY @ 60° F. 0.87 

POUNDS PER GALLON 7.11 

COLOR 

RED 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON FM-AL-26 SYNTHETIC 

FOOD MACHINERY AIR CYLINDER LUBRICANT 

THE ALITHICON FM-AL-26 SYNTHETIC FOOD MACHINERY AIR CYLINDER 

LUBRICANT IS FORMULATED WITH USDA/FDA APPROVED SYNTHETIC FULIDS 

AND FOOD GRADE ADDITIVES, MEETING WITH USDA/FDA APPROVED SYNTHETIC 

FLUIDS AND FOOD GRADE ADDITIVES, MEETING REQUIREMENTS FOR THE H-1 

RATING UNDER TITLE 21 CFR. 178.3570, FOR USE IN FOOD AND POULTRY 

PLANTS WHERE INCIDENTAL CONTACT OF THE LUBRICANT WITH THE EDIBLE 

PRODUCTS BEING MANUFACTURED IS POSSIBLE. 

THE ALITHICON FM-AL-26 SYNTHETIC FOOD MACHINERY AIR CYLINDER 

LUBRICANT IS ODORLESS, TASTELESS, AND COLORLESS, WATER CLEAR, YET IT 

WILL GREATLY EXTEND AIR TOOL LIFE, PLUS OPTIMIZE PNUEMATIC SYSTEM 

PERFORMANCE. 

BECAUSE MOISTURE IS EVER-PRESENT IN AIR LINES, DUE TO THE EXPANSION 

AND COOLING OF COMPRESSED AIR, THE ALITHICON FM-AL-26 SYNTHETIC 

FOOD MACHINERY AIR CYLINDER LUBRICANT VIRTUALLY ELIMINATES TOOL 

VALVE STICKING, PREVENTS LUBRICATOR CLOGGING, AND INHIBITS POWER- 

THIEVINGDEPOSITS BY ABSORBING SIGNIFIGANT AMOUNTS OF MOISTURE, 

WHICH CAUSES GUMMING. IN ADDITION, IT GREATLY EXTENDS THE LIFE OF 

INTERNAL PARTS BY REDUCING FRICTION AND WEAR. 

WHEN USING THE ALITHICON FM-AL-26, GALLING, SCUFFING, AND GUMMING IN 

AIR CYLINDERS IS ELIMINATED. 


* EFFECTIVE AIR CYLINDER LUBRICANT MEETING USDA/FDA H-1 REQUIREMENTS 

* ELIMINATES AIR CYLINDER / AIR TOOL GALLING, SCUFFING, AND GUMMING 

* EXTENDS AIR CYLINDER / AIR TOOL LIFE AS MUCH AS 800% 

PLEASE SEE REVERSE SIDE FOR TYPICAL SPECIFICATIONS 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON FM-AL-26 SYNTHETIC 

FOOD MACHINERY AIR CYLINDER LUBRICANT 


VISCOSITY, CALCULATED 

SUS @ 100° F. 

SUS @ 210° F. 

VISCOSITY, ASTM D-445 

Cst. @ 40° C 

Cst. @ 100° c 

TEST 

RESULTS 


LOAD CARRYLING ABILITY 

FALEX TEST (ASTM D-2670) 

NON-SIEZURE LOAD, lbs. 1095 

POUR POINT (ASTM D-97) 

° F. 

° C. 

RUST TEST (ASTM D-665 A) 

96 

40 

26 

4.9 

-5 

-23 

PASS 


* 24 / 1 QUART CASE 


* 6 GALLON PAIL 


* BULK 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON SYNTHETIC TURBINE OIL 

THE ALITHICON SYNTHETIC TURBINE OIL HAS BEEN FORMULATED, AND IS DESIGNED TO 

LUBRICATE INDUSTRIAL MACHINERY WHERE RESISTANCE TO EXTERNAL, RADIANT HIGH 

TEMPERATURES, EXTENDED DRAIN INTERVALS, COMPATIBILITY TO CERTAIN MATERIALS 

BEING MANUFACTURED AND PROCESSED, AND CLEANLINESS ARE NECESSARY. 

THE ALITHICON SYNTHETIC TURBINE OIL IS FORTIFIED WITH ANTI-WEAR (AW) AND RUST AND 

OXIDATION (R & O) ADDITIVES, AND WILL NOT MIX WITH WATER. 

THE ALITHICON SYNTHETIC TURBINE OIL WILL GREATLY REDUCE LEAKS AND BLOWN HOSES 

IN HYDRAULIC AND CIRCULATING SYSTEMS AND WILL ALSO GREATLY EXTEND OIL PUMP AND 

MOTOR LIFE. 

THE ALITHICON SYNTHETIC TURBINE OIL HAS AN EXTREMELY LOW POUR POINT AND A HIGH 

VOLITIZATION TEMPERATURE. EVEN IF THE HIGH VOLATIZATION TEMPERATURE IS REACHED, 

DURING MACHINERY OPERATION, THERE WILL BE NO RESIDUE GENERATED INSIDE THE 

EQUIPMENT. 


* WILL NOT MIX WITH WATER * EXTENDED DRAIN INTERVALS 

* REDUCES LEAKS AND BLOWN HOSES BY 80% 

* WILL NOT SHELLAC, VARNISH, OR LEAVE ANY RESIDUE 

IF SUBJECTED TO EXTREMELY HIGH TEMPERATURES 

* EXTENDS LUBRICANT PUMP AND MOTOR LIFE BY 500% 

* COMPATIBLE WITH CERTAIN MATERIALS BEING MANUFACTURED 

* COLORLESS 

APPLICATIONS: 

HYDRAULIC SYSTEMS, FLUID BEARING LUBRICANT, CHAINS, CENTRIFUGES, AND MANY MORE. 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON SYNTHETIC TURBINE OIL 

PRODUCT CODE 6610 6615 6620 6630 6640 6650 6660 

ISO GRADE 32 32 68 100 150 220 320 

SAE VISCOSITY GRADE 10 10 20 30 40 50 60 

VISCOSITY INDEX (ASTM D-2270) 150 150 150 165 165 165 165 

POUR POINT, ° F. (ASTM D-97) -90 -90 -90 -85 -85 -70 -70 

FLASH POINT, ° F. (COC) (ASTM D-92) 495 495 495 505 505 510 515 

AUTOIGNITION TEMPERATURE, ° F. (ASTM D-2155) 710 710 710 715 715 722 722 

EVAPORATION LOSS, N² ATMOSPHERE 760 mm, 3 3 3 3 2 2 2 

% RESIDUE BUILD-UP @ 1,000° F. UNTIL COMPLETE 0 0 0 0 0 0 0 

ROTARY BOMB OXIDATION 300° F., 1235 1235 1235 1250 1370 1390 1450 

4-BALL, SCAR DM. (mm), (ASTM D-189) 

>> 10 kg @ 1,800 R.P.M. @ 150° F. FOR 30 MINUTES 

>> 40 kg @ 1,200 R.P.M. @ 167° F. FOR 60 MINUTES 

1.50 1.50 

1.55 

1.50 1.50 1.50 1.50 1.50 

VICKERS PUMP TEST @ 150° F. 

TOTAL WEIGHT LOSS (ASTM D-2892) 9.9 

ISO CLEANLINESS CODE RATING (DIS-4406) 10/8 10/8 10/8 10/8 10/8 10/8 10/8 

COLOR CLEAR/ CLEAR/ CLEAR/ CLEAR/ CLEAR/ CLEAR/ CLEAR/ 


* 6 / 1 GALLON CASE * 6 GALLON PAIL * 55 GALLON DRUM 

* 330 GALLON NON-RETURNABLE (DISPOSABLE) TOTE * BULK 

___________________________________________________________________________________ 


PHONE: 229-883-9515 / FAX: 229-883-9516 


1101 ALITHICON PARA/SYNTHETIC 

STOKER TRAVELING GRATE 

BEARING LUBRICANT 

THE 1101 ALITHICON PARA/SYNTHETIC STOKER TRAVELING GRATE BEARING 

LUBRICANT WAS FORMULATED AND FIRST USED IN A PAPER MILL POWER HOUSE 

STOKER IN 1982 WITH EXCELLENT RESULTS. 

THE ORIGINAL PAPER MILL USER EXPERIENCED A 300% INCREASE IN STOKER AND 

TRAVELING GRATE BEARINGS AND SHAFTS, OVER THE BEST LUBRICANT PREVIOUSLY 

USED. 

PLANNED STOKER REBUILD WAS EXTENDED FROM AN ANNUAL TASK TO A REBUILD 

EVERY 3 YEARS. 


WITHSTANDS HIGH TEMPERATURES, UP TO 500° F 

WILL NOT HARDEN IN SERVICE 

WILL NOT PLUG BEARING LUBRICANT FEED LINES 

EASILY DISPENSED BY HANDGUNS, AIR GUNS, OR CENTRALIZED 

LUBRICATING SYSTEMS 

TIMKEN O.K. LOAD RATING, 60 lbs, MIN. 

EXTENDS STOKER TRAVELING GRATE BEARINGS AND SHAFT LIFE OF UP TO 

300% OVER THE MORE COMMONLY USED GREASE 


50 - 14.5 oz TUBE CASE 120 lb KEG 

6 - 7.5 lbs CAN CASE 420 lb DRUM 

45 lb PAIL BULK 

PLEASE SEE REVERSE SIDE FOR TYPICAL SPECIFICATIONS 


PHONE: 229-883-9515 / FAX: 229-883-9516 



1101 ALITHICON PARA/SYNTHETIC 

STOKER TRAVELING GRATE BEARING LUBRICANT 

BASE OIL INFORMATION 

TEST RESULTS 

NLGI GRADE 1 

WORKED PENETRATION (ASTM D-217) 315 

PROLONGED WORKED PENETRATION (ASTM D-217), % CHANGE 0.78 

DROPPING POINT, MIN. (ASTM D-566), ° F 500 

TIMKEN O.K. LOAD, lbs MIN. (ASTM - 2782) 60 

ACID RESISTANCE 

EXCELLENT 

ROLL STABILITY (ASTM D-1831), % CHANGE 0.6 

LEAKAGE TENDENCIES, % MAX. (ASTM D-1264) 0.3 

WATER WASHOUT, % MAX. (ASTM - 1264) 

30° C (100° F) 

79° C (175° F) 

OXIDATION STABILITY, MAX. (ASTM D-942), 

PRESSURE DROP @ 100 HRS., KPS (PSI) 2 

FOUR BALL METHOD, MAX. LOAD 

WHICH WELDING OCCURS, kg (lbs) (ASTM D-2598) 2.64 

WEAR PREVENTATIVE CHARACTERISTICS (ASTM D-2266) 

MAX. SCAR DIAMETER 40 kg LOAD, 1200 RPM 

DENSITY, lbs PER GALLON 7.7 

COPPER STRIP CORROSION (ASTM D-130) 

0 

0 

3 mm 

1A (PASS) 

VISCOSITY, SUS @ 100° F 


VISCOSITY INDEX 

BASE OIL PARTICLE COUNT RATINGS 

ISO CLEANLINESS CODE RATING (DIS 4406) 

NAS 1638 CLEANLINESS CODE RATING 

SAE - J1165 CLEANLINESS CODE RATING 

1225 

75 

110 

16 / 13 

7 

4 

1101 & 1102 LUBRICANT COMPATIBILITY 

COMPATIBLE INCOMPATIBLE BORDERLINE 

CALCIUM 12-HYDROXY BARIUM COMPLEX CALCIUM SULFONATE COMPLEX 

LITHIUM COMPLEX 

CALCIUM STEARATE 

SILICA 

CALCIUM COMPLEX 

ALUMINUM COMPLEX 

BENTONE / CLAY 

LITHIUM STEARATE 

LITHIUM 12-HYDROXY 

POLYUREA 

SODIUM 


PHONE: 229-883-9515 / FAX: 229-883-9516 



PHONE: 229-883-9515 / FAX: 229-883-9516 


2212 ALITHICON BEARING LUBRICANT 

A TRULY VERSATILE, LONG-LASTING, GENERAL PURPOSE BEARING LUBRICANT, THIS PRODUCT IS 

FORMULATED FOR USE TO LUBRICATE BOTH FRICTION AND ANTI-FRICTION BEARINGS FOUND ON 

CONSTRUCTION, FARM, TRUCKING, GENERAL INDUSTRIAL BEARING MACHINERY. 

THE 2212 ALITHICON BEARING LUBRICANT RESISTS WATER WASH-OUT, GREATLY REDUCES LUBRICANT 

CONSUMPTION (AS MUCH AS 70%), WITHSTANDS TEMPERATURES OF UP TO 560° F, AND RATES AN O.K. 

TIMKEN LOAD OF 85 lbs, MIN. 

SINCE THE 2212 ALITHICON LUBRICANT REDUCES GREASE CONSUMPTION AS MUCH AS 70%, USERS 

FIND THAT LESS MONEY WAS SPENT PER ANNUM THAN WHEN USING THE CHEAPER GREASES THEY 

NORMALLY USED. THEY ALSO STATED THAT IT EXTENDED THEIR BEARING LIFE 300%, TOO. 

2212 C/B (NLGI-2) IS RECOMMENDED FOR USE TO LUBRICATE ANTI-FRICTION BEARINGS WHICH OF UP TO 3,000 

R.P.M.'S, MAXIMUM. 

2212 C/A (NLGI-2) IS RECOMMENDED FOR USE TO LUBRICATE ANTI-FRICTION BEARINGS WHICH OPERATE ABOVE 

3,000 R.P.M.'S. 

MEETS AND EXCEEDS MILITARY SPECIFICATIONS OF: MIL-G-18709, MIL-G-23827-B, 

MIL-G-25760-A, MIL-G-21164-D, MIL-G-81322-D 


** REDUCE YOUR GREASE COSTS BY 35%** 

GUARANTEED 

* WILL NOT MELT AND RUN FROM BEARINGS * TACKY, WILL NOT SLING FROM BEARINGS 

* WATER RESISTANT * FORMS ITS OWN SEAL, SEALING OUT CONTAMINATION 

* TIMKEN O.K. LOAD RATING OF 85 lbs, MIN. * EXTENDS BEARING LIFE OF UP TO 300% 

* REDUCES GREASE CONSUMPTION AS MUCH AS 70% * CONTAINS NO SILICONES 

2212 LUBRICANT COMPATIBILITY 

COMPATIBLE_ - - - - - - - - - - - - - INCOMPATIBLE__ - - - - - - - - - - - - -> 

CALCIUM STEARATE ALUMINUM COMPLEX BARIUM COMPLEX SODIUM 

CALCIUM HYDROXY CALCIUM COMPLEX CALCIUM SULFONATE COMPLEX LITHIUM COMPLEX 

SILICA BENTONE / CLAY LITHIUM STEARATE LITHIUM 12-HYDROXY POLYUREA 


* 50 - 14.5 oz TUBE CASE * 120 lb KEG 

* 6 - 7.5 lb CANS (45 lbs) CASE * 420 lb DRUM 

* 45 lb PAIL * BULK 

SEE REVERSE SIDE FOR TYPICAL SPECIFICATIONS, TEST RESULTS, APPLICATIONS 


PHONE: 229-883-9515 / FAX: 229-883-9516 



CONSTRUCTION APPLICATIONS: BACKHOE AND LOADER BUCKET PINS AND BUSHINGS, UNIVERSAL JOINTS, 

ASPHALT PLANT INJECTION SCREW BEARINGS, ASPHALT SPREADER AUGER AND CONVEYOR BEARINGS, 

TRENCHER BEARINGS, CONCRETE READY MIX TRUCK DRUM ROLLER BEARINGS, ROCK QUARRY TAIL ROLLER 

LOAD-OUT CONVEYOR BEARINGS, ETC. 

FARM APPLICATIONS: TREE SHAKER BEARING LUBRICATION, TRACTOR BEARINGS PEANUT COMBINE BEARINGS, 

GRAIN COMBINE BEARINGS, HARROW BEARINGS, BEARING LUBRICATION FOR ALL FARM MACHINERY 

TRUCK APPLICATIONS: UNIVERSAL JOINTS, KING PIN AND BUSHINGS, CONCRETE READY MIX TRUCK DRUM 

ROLLER BEARINGS, ALL GREASE LUBRICATION FOR TRUCKS (EXCEPT AS A FIFTH WHEEL LUBRICANT; FOR THIS 

APPLICATION, WE RECOMMEND THE USE OF THE 9902 ALITHICON SYNTHETIC EX-TEMP LUBRICANT) 

GENERAL INDUSTRIAL APPLICATIONS: GENERAL PLANT PILLOW BLOCK BEARINGS, ACENTRIC BEARINGS, 

CONVEYOR BEARINGS, FORKLIFTS, PELLET MILL BEARINGS, EXPELLER BEARINGS, ETC. 

LOGGING EQUIPMENT: SKIDDER PINS & BUSHINGS, UNIVERSAL JOINTS, PIVOT PINS - FELLER BUNCHERS, BOTH 

SAW HEAD AND SHEAR HEAD BEARINGS - ALL GREASE / LUBE POINTS ON KNUCKLE BOOM LOADERS - LOG 

TRUCK CHASSIS, ETC. 



NLGI GRADE 2 

WORKED PENETRATION 271 

PROLONGED WORKED PENETRATIONS (ASTM D-217), % CHANGE + 0.002 

DROPPING POINT, MIN. (ASTM D-566) 

RECOMMENDED OPERATING RANGE 

NON-MELT 

0° F - 600° F 

TIMKEN O.K. LOAD, lbs, MIN. (ASTM 2782) 85 


EXCELLENT 

ROLL STABILITY (ASTM D-1831), % CHANGE > 1.1 


WATER WASHOUT, % MAX. (ASTM D-12640) 

39° C (100° F) 

79° C (175° F) 

OXIDATION STABILITY, MAX. (ASTM D-942) 

PRESSURE DROP @ 100 hrs, KPS (PSI) 3 

0.7 

0.85 

FOUR BALL METHOD, MAX. LOAD WHICH WELDING 2.76 

WEAR PREVENTATIVE CHARACTERISTICS (ATSM D-2666) 

MAX., SCAR DIAMETER 40 kg LOAD, 1200 R.P.M. 

.425 mm 

COLOR 

BASE OIL: 

VISCOSITY SUS @ 100° F 

VISCOSITY CTS @ 100° C 


VISCOSITY CTS @ 40° C 


LOW TEMP TORQUE-WHEEL BEARING, 

LOWEST OPERATIONAL TEMPERATURE (ASTM TEST METHOD D- 

4693) 

LOW DISPENSABLE / PUMPABLE 

RED 

693 

15.1 

77 

150 

110 

+2° F 

0° F

ALITHICON 3456 SYNTHETIC FLASH-FREEZE 

ALITHICON 3456 SYNTHETIC FLASH-FREEZE 

BEARING LUBRICANT (NLGI - 2) 

THE ALITHICON 3456 SYNTHETIC FLASH-FREEZE BEARING LUBRICANT IS FORMULATED AND DESIGNED TO 

PROLONG AND SUCESSFULLY PROTECT BEARINGS, WHICH MUST OPERATE IN EXTREMELY COLD TEMPERATURES 

AS LOW AS -50° F, BUT WILL ALSO PERFORM SUCESSFULLY IN TEMPERATURES AS HIGH AS +500° F. 

THE ALITHCON 3456 SYNTHETIC FLASH-FREEZE BEARING LUBRICANT CARRIES AN FDA / USDA RATING OF H-1, 

WHICH IS ACCEPTABLE FOR INCIDENTAL FOOD CONTACT. 

THE ALITHICON 3456 SYNTHETIC FLASH-FREEZE BEARING LUBRICANT IS VIRTUALLY WATERPROOF, RATES AN O.K. 

LOAD OF 70 lbs, MIN., AND IS DESIGNED TO LUBRICATE BOTH FRICTION AND ANTI-FRICTION BEARINGS. 

THE ALITHICON 3456 BEARING LUBRICANT IS DESIGNED TO LUBRICATE BEARINGS WITH SPEEDS OF, FROM 1 TO 

7,000 R.P.M.’S. 

A USDA APPROVED, BROAD-SPECTRUM BIOCIDE IS FORMULATED INTO THE ALITHICON 3456 SYNTHETIC FLASH- 

FREEZE BEARING LUBRICANT, WHICH ELIMINATES ANY CONCERN OF PROMOTING THE GROWTH OF, OR 

EXTENDING THE CONTAMINATION OF THE FOOD PRODUCTS BEING MANUFACTURED OR PROCESSED. 

THE USDA APPROVED, BROAD-SPECTRUM BIOCIDE ELIMINATES ANY CONCERN OF TRANSFERRING, ESPECIALLY 

SALMONELLA IN POULTRY-PROCESSING PLANTS, UNDESIRABLE BACTERIA WHEN IT IS INTRODUCED TO THE 

BEARING LUBRICANT. 

WHEN BACTERIA IS INTRODUCED TO THE ALITHICON 3456 SYNTHETIC FLASH-FREEZE BEARING LUBRICANT, AFTER 

A MAXIMUM OF 30 MINUTES, THE BACTERIA IS NEUTRALIZED. 

IT IS NOT NECESSARY TO ACCEPT SHORT BEARING LIFE, INCREASED MAINTENANCE, AND DECREASED 

PRODUCTION TO COMPLY WITH THE FDA / USDA REGULATIONS WHEN THE ALITHICON 3456 SYNTHETIC FLASH- 

FREEZE BEARING LUBRICANT IS AVAILABLE. 


A LONG-LIFE BEARING LUBRICANT * MEETS WITH FDA / USDA H-1 REQUIREMENTS 

HAS A TEMPERATURE OPERATING RANGE OF FROM -50° F TO +550° F 

VIRTUALLY WATERPROOF * RATES AN O.K. TIMKEN LOAD OF 70 lbs, MIN. 

REDUCES LUBRICANT CONSUMPTION OF UP TO 300% 

EXTENDS BEARING LIFE OF UP TO 500% 

APPLICATIONS: 

POULTRY, PORK, BEEF, AND VEGETABLE PROCESSING PLANTS WHICH HAVE QUICK-FREEZE DEPARTMENTS, 

SATILITE DISH SYSTEMS WHICH OPERATE IN EXTREMELY NORTHERN OR EXTREMELY SOUTHERN HEMISHPHERES, 

AND TRUCKS OR CONSTRUCTION EQUIPMENT WHICH OPERATE IN EXTREMELY COLD ENVIRONMENTS. 

CHECK THIS ALITHICON LUBRICANT FOR USDA APPROVAL, FOR USE IN FOOD PROCESSING 

PLANTS IN THE 2002 NSF WHITE BOOK (NSF INTERNATIONAL / NON-FOOD COMPOUNDS) AT 

www.nsf.org/usda 


PHONE: 229-883-9515 / FAX: 229-883-9516 




ASTM TEST 

RESULTS 

NLGI GRADE * * * * * 2 

COLOR * * * * * CREAM WHITE 

TEXTURE * * * * * SMOOTH 

UN-WORKED PENETRATION D-217 280 

WORKED MECHANICAL STABILITY 

10,000 STROKES 

100,000 STROKES 

D-217 

D-217 

274 

271 

ROLL STABILITY, % CHANGE D-1831 < 1.4 

DROPPING POINT, ° F D-2265 590 

OIL SEPARATION D-1742 0.07 

WHEEL BEARING LEAKAGE, gr D-4290 0.15 

TIMKEN O.K. LOAD, lbs, MIN. D-2782 70 

4 BALL E.P. TEST 

LOAD WEAR INDEX, kg 

WELD POINT, mm 

CORROSION RESISTANCE 

RUST TEST RATING 

SALT FOG, hrs TO FAILURE 

OXIDATION RESISTANCE 

BEARING LIFE, hrs 

BOMB OXIDATION, PSI DROP AFTER 1,000 hrs 

D-2266 

D-1743 

B-117 

D-3527 

D-942 

0.36 

497 

PASS 

> 450 

340 

4.1 

WATER WASH-OUT, 79° C, % LOSS D-1264 1.2 

LOW TEMP TORQUE WHEEL BEARINGS 

TEST @ -40° C, Nm D-4693 1.4 

DESIRABLE OPERATING TEMPERATURE RANGE 

-50° F TO 550° F 

BASE FLUID INFORMATION 


SPECIFICATION RESULT COMPATIBLE INCOMPATIBLE BORDERLINE 

VISCOSITY @ 100° C, cst 9 BARIUM COMPLEX CALCIUM COMPLEX ALUMINUM COMPLEX 

VISCOSITY @ 40° C, cst 96 CALCIUM STEARATE BENTONE / CLAY CALCIUM 12 HYDROXY 

VISCOSITY @ 210° C, SUS 38 LITHIUM COMPLEX POLYUREA LITHIUM STEARATE 

VISCOSITY @ 100° C, SUS 482 SILICA SODIUM LITHIUM-12 HYDROXY 

FLASH POINT, ° F 570 CALCIUM SULFONATE 

COMPLEX 

POUR POINT, ° F - 70 


* 30 / 14.5 oz TUBE CASE * 50 / 14.5 oz TUBE CASE * 35 lb PLASTIC PAILS 

* 45 lb PLASTIC PAILS * 120 lb KEGS * 420 lb DRUMS 

* BULK 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON 4522-FM SYNTHETIC FOOD MACHINERY 

BEARING LUBRICANT (NLGI-2) 

THE ALITHICON 4522-FM SYNTHETIC FOOD MACHINERY BEARING LUBRICANT IS DESIGNED TO MEET TODAY'S 

DEMANDING REQUIREMENTS OF THE MODERN FOOD PROCESSING EQUIPMENT, WHICH OPERATES UNDER 

EXTREMELY HIGH TEMPERATURES, HEAVY LOADS, HIGH SPEEDS, AND WET CONDITIONS. 

THE ALITHICON 4522-FM SYNTHETIC FOOD MACHINERY BEARING LUBRICANT IS FORMULATED TO PERFORM IN A 

SUPERIOR MANNER WITH THE FOLLOWING OUTSTANDING FEATURES: A BROAD OPERATING RANGE (-5° F TO 750° 

F), WATERPROOF, MECHANICALLY STABILE (RESISTANCE TO HARDENING OR SOFTENING IN SERVICE), AND RUST 

AND OXIDATION RESISTANCE. 

A USDA APPROVED, BROAD-SPECTRUM BIOCIDE IS FORMULATED INTO THE ALITHICON 4522-FM SYNTHETIC FOOD 

MACHINERY BEARING LUBRICANT, WHICH ELIMINATES ANY CONCERN OF PROMOTING THE GROWTH OF, OR 

EXTENDING THE CONTAMINATION OF THE FOOD PRODUCTS BEING MANUFACTURED OR PROCESSED. 

THE USDA APPROVED, BROAD-SPECTRUM BIOCIDE ELIMINATES ANY CONCERN OF TRANSFERRING, ESPECIALLY 

SALMONELLA IN POULTRY-PROCESSING PLANTS, UNDESIRABLE BACTERIA WHEN IT IS INTRODUCED TO THE 


WHEN BACTERIA IS INTRODUCED TO THE ALITHICON 4522-FM SYNTHETIC FOOD MACHINERY BEARING LUBRICANT, 

AFTER A MAXIMUM OF 30 MINUTES, THE BACTERIA IS NEUTRALIZED. 

EVEN THOUGH THE ALITHICON 4522-FM SYNTHETIC FOOD MACHINERY BEARING LUBRICANT MEETS WITH THE 

FDA/USDA PURITY REQUIREMENTS, WITH AN H-1 RATING FOR INCIDENTAL CONTACT WITH THE FOOD PRODUCTS 

BEING PROCESSED, IT IS RECOMMENDED TO BE USED AS ONE LUBRICANT, TO LUBRICATE ALL BEARINGS WHICH 

HAS TO BE LUBRICATED WITH AN NLGI-1 OR AN NLGI-2 GREASE, EVEN ELECTRIC MOTOR BEARINGS. 

THE ALITHICON 4522-FM SYNTHETIC FOOD MACHINERY BEARING LUBRICANT CONTAINS NO TEFLON OR PTFE, AND 

IS THE PREFERRED BEARING LUBRICANT FOR USE TO LUBRICATE BEARINGS WHICH PROCESS TOBACCO. 

SINCE THE ALITHICON 4522-FM SYNTHETIC FOOD MACHINERY BEARING LUBRICANT IS COMPATIBLE WITH, AND 

WILL MIX FAVORABLY WITH ALL OTHER GREASES, CONCERN IN MIXING GREASES, OR CHANGE OVER FLUSHING 

PROCEDURES, ARE NOT NECESSARY. 

WITH THE AVAILABILITY OF THE ALITHICON 4522-FM SYNTHETIC FOOD MACHINERY BEARING LUBRICANT, IT IS NOT 

NECESSARY TO SETTLE FOR SHORT BEARING LIFE, DECREASED PRODUCTION, AND EXCESSIVE EQUIPMENT 

REPAIRS, JUST TO MEET WITH THESE USDA/FDA PURITY REQUIREMENTS. 

ALSO AVAILABLE AS ALITHICON #4521-FM FOOD MACHINERY LUBRICANT (NLGI-1). 

THE ALITHICON #4521-FM SYNTHETIC FOOD MACHINERY BEARING LUBRICANT 

(NLGI-1) IS AN EXCELLENT CHOICE TO PUMP THROUGH CENTRALIZED LUBE SYSTEMS, WHICH ARE 

DESIGNED FOR PUMPING A LIGHT-WEIGHT GREASE OR A HEAVY-WEIGHT OIL. 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON 4522-FM SYNTHETIC FOOD MACHINERY BEARING LUBRICANT 

(NLGI-2) 


* TOTALLY WATERPROOF * DOES NOT CONTAIN TEFLON,PTFE, OR SILICONES. 

* ANTI-MICROBIAL ** ANTI-FUNGAL ** ANTI-BACTERIAL 

* WITHSTANDS HIGH TEMPERATURES OF UP TO 750° F * PREVENTS RUSTING IN BEARINGS 

* RATES AN O.K. TIMKEN LOAD OF 80 lbs., MIN. * MEETS THE FDA / USDA OF H-1 FOR PURITY 

* TACKY - REDUCES LUBRICANT CONSUMPTION AS MUCH AS 500% 

* EXTENDS BEARING LIFE AS MUCH AS 400% 

APPLICATIONS: 

POULTRY PROCESSING MACHINERY, PICKER BEARINGS, PORK PROCESSING MACHINERY, BEEF PROCESSING 

MACHINERY, BAKERY MACHINERY, BOTTLING PLANT MACHINERY, FILLING MACHINES, CROWNERS, BOTTLE 

WASHERS, TOBACCO PROCESSING MACHINERY, ELECTRICAL POWER GENERATING TRAVELING SCREENS, DAIRY 

EQUIPMENT, ETC. THE ALITHICON 4521-FM AND ALITHICON 4522-FM ARE EXCELLENT CHOICES FOR LUBRICATING 

COUPLINGS, WHICH OPERATE FROM 1 - 5,000 R.P.M.’S. 

CHECK THE ALITHICON LUBRICANT FOR USDA APPROVAL, FOR USE IN FOOD PROCESSING 




PRODUCT CODE 4521-FM 4522-FM 

NLGI GRADE 1 2 

WORKED PENETRATION, 60 STROKES (ASTM D-217) 339 290 

DROPPING POINT, MINIMUM (ASTM D-566) NONE NONE 

LUBRICATING OPERATING RANGE -8 TO 750° F. -5° TO 750° F. 

TIMKEN O.K. LOAD, lbs, MINIMUM (ASTM D-2782) 80 80 

ACID RESISTANCE EXCELLENT EXCELLENT 

WATER WASHOUT, % MAX. 

38° C. (100° F) 

70° C. (175° F.) 

D-1264 

0.02 

0.02 

FOUR BALL METHOD, MAX. LOAD WHICH WELDING OCCURS D-2596 3.94 

COLOR CLEAR CLEAR 

TEXTURE SLIGHT TACK SLIGHT TACK 

EVAPORATION LOSS @ 350° F, WT. % (ASTM D-2595) 0.2 0.2 

USP SYNTHETIC HYDROCARBON BASE OIL VISCOSITY @ 40° C 150 150 

BASE FLUID VISCOSITY INDEX 120 120 

• 30 - 14.5 oz TUBES / CASE 

• 50 - 14.5 oz TUBES / CASE 

• 35 lb PAIL 


• 120 lb KEG 

• 420 lb DRUM 

• BULK 

ALITHICON 4522-FM LUBRICANT COMPATIBILITY 

COMPATIBLE 

CALCIUM 12-HYDROXY BARIUM COMPLEX CALCIUM SULFONATE COMPLEX 

LITHIUM COMPLEX CALCIUM STEARATE LITHIUM STEARATE 

SILICA CALCIUM COMPLEX LITHIUM 12-HYDROXY 

ALUMINUM COMPLEX BENTONE / CLAY POLYUREA 

SODIUM 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON 9992-TL PARA/SYNTHETIC 

BEARING LUBRICANT 

THE 9992-TL ALITHICON PARA/SYNTHETIC BEARING LUBRICANT WAS INITIALLY FORMULATED TO 

WITHSTAND THE HARSH, WET, AND HIGH TEMPERATURE ENVIRONMENTS COMMONLY FOUND IN THE 

TEXTILE INDUSTRY. 

AFTER THE INTRODUCTION OF THE 9992-TL ALITHICON, IT WAS TESTED AND FOUND TO BE FAR- 

SUPERIOR TO LUBRICANTS NORMALLY BEING USED IN THE PAPER INDUSTRY, SEWAGE TREATMENT 

PLANTS, AND OTHER INDUSTRIES WHERE THESE HARSH, WET ENVIRONMENTS ARE FOUND. 

THE ALITHICON 9992-TL ALSO THE PERFERRED LUBRICANT TO LUBRICATE BEARINGS FOUND ON SKI 

RESORT AND GOLF COURSE EQUIPMENT. THE ALITHICON 9992 LUBRICANT WILL NOT KILL GRASS, 

UNDER NORMAL USE. 

MEETS AND EXCEEDS MILITARY SPECIFICATIONS FOR MIL-G-18709 AND 

MIL-G-18709 (AMEND 3) 


* WATERPROOF * CONTAINS NO SILICONES 

* RESISTS DECOMPOSITION WHEN INTRODUCED TO MOST ACIDS 

* ACCEPTABLE OPERATING TEMPERATURE RANGE: - 40° F. TO 595° F. 

* RATES AN O.K. TIMKEN LOAD OF 85 lbs., MIN. 

* REDUCES LUBRICANT CONSUMPTION OF UP TO 300% 

* EXTENDS BEARING LIFE OF UP TO 500% 

* WILL NOT SLING FROM BEARINGS 

* MEETS WITH USDA REQUIREMENTS OF H-2 FOR LUBRICATING EQUIPMENT BEARINGS FOUND IN 

FOOD-PROCESSING PLANTS 

APPLICATIONS: 

(TEXTILE PLANTS) WASH BOX BEARINGS, DYE VAT BEARINGS, DYE RANGE BEARINGS 

( PAPER MILL) WET END BEARINGS, PUMP BEARINGS, FLOCKULATOR BEARINGS, 

** SEWAGE TREATMENT PLANT BEARINGS ** BOAT TRAILER WHEEL BEARINGS, ELECTRIC MOTOR BEARINGS, 

ROBBINS WEBB SCREEN BEARINGS, BLUNGER BEARINGS, GENERAL STEEL MILL BEARINGS, GENERAL POWER 

PLANT BEARING LUBRICANT, TRAVELING SCREENS, DREDGING EQUIPMENT, SKI RESORT AND GOLF COURSE 

EQUIPMENT BEARINGS, ETC. 

EXCELLENT CHOICE TO LUBRICATE PRECISION-TYPE BEARINGS, 

WHICH OPERATE UP TO 10,000 R.P.M.’S. 



PHONE: 229-883-9515 / FAX: 229-883-9516 


9992-TL TECHNICAL SPECIFICATIONS 

NLGI GRADE 2 

TEXTURE 

SMOOTH 

COLOR 

CREAM-WHITE 

TEST ASTM METHOD TYPICAL RESULTS 

PENETRATION @ 77° F 

D-217 

UNWORKED 

276 

ROLL STABILITY (% CHANGE) D-1831 293 (4.0) 

RUST PROTECTION D-1743 PASS 

DROPPING POINT, ° F. D-D-2265 595 

4 BALL E.P. PERFORMANCE 

D-2596 

LOAD WEAR INDEX 

72 

TIMKEN O.K. LOAD, lbs., MIN. D-2509 85 

WHEEL BEARING LIFE TEST, hrs D-3527 120 

WATER WASHOUT @ 175° F., % D-1264 0.004 

OIL SEPARATION, % LOSS D-1742 0.01 

BASE OIL CHARACTERISTICS 

VISCOSITY @ 210° F., S.U.S. D-2161 70 

LOW TEMP TORQUE-WHEEL 

BEARING, 

LOWEST OPERATIONAL 

D-4693 

- 40° F. 

LOW DISPENSABLE / PUMPABLE 

GREASE MOBILITY TEST 

U.S. STEEL METHOD - 40° F. 

9992-TL LUBRICANT COMPATIBILITY 


BARIUM COMPLEX CALCIUM COMPLEX ALUMINUM COMPLEX 

CALCIUM STEARATE BENTONE / CLAY CALCIUM 12-HYDROXY 

LITHIUM COMPLEX POLYUREA LITHIUM STEARATE 

SILICA SODIUM LITHIUM 12-HYDROXY 

CALCIUM SULFONATE COMPLEX

B-51 ALITHICON 

HIGH TEMPERATURE BEARING LUBRICANT 

THE B-51 ALITHICON SYNTHETIC HIGH TEMPERATURE BEARING LUBRICANT IS SPECIFICALLY 

FORMULATED TO BE APPLIED WHERE CONVENTIONAL SOAP-THICKENED, OR SO CALLED NON-MELT 

GREASES, WILL NOT PROVIDE ADEQUATE PERFORMANCE. 

THE B-51 ALITHICON LUBRICANT IS A SYNTHETICALLY THICKENED GREASE WHICH EMPLOYS A HIGH 

THERMAL STABLE SYNTHETIC BASE FLUID, ALLOWING IT TO PROVIDE SUPERIOR LUBRICATION AND 

PROTECTION TO BEARINGS WHICH MUST OPERATE IN TEMPERATURES OF UP TO 700° F WITHOUT 

MELTING OR HARDENING IN SERVICE. 

TWO ADDITIONAL IMPORTANT FEATURES OF THE B-51 ALITHICON LUBRICANT IS: BEING WATERPROOF, 

RESISTING WATER WASH-OUT, AND HAVING A LONG SERVICE LIFE, REDUCING GREASE CONSUMPTION 

AS MUCH AS 800% WHEN COMPARED TO OTHER GREASES NORMALLY USED IN THESE APPLICATIONS. 

THE B-51 ALITHICON LUBRICANT HAS AN O.K. TIMKEN LOAD RATING OF 100 lbs, MINIMUM, AND WILL 

PRODUCE AND EXTENDED BEARING LIFE OF UP TO 400%. 

IT IS NOT NECESSARY TO LIMIT THE USE OF THE B-51 ALITHICON SYNTHETIC BEARING LUBRICANT 

ONLY TO BEARINGS OPERATING UNDER EXTREME TEMPERATURES OR WET CONDITIONS TO JUSTIFY 

THE ADDITIONAL COST. MANY LONG-TIME USERS OF THE B-51 ALITHICON LUBRICANT STATE THAT IT 

WAS PRIMARILY PURCHASED FOR USE IN THESE EXTREME, HIGH MAINTENANCE AREAS, BUT IT WAS 

LATER TRIED IN BEARINGS ON MACHINERY OPERATING IN AMBIENT TEMPERATURES AND UNDER 

AVERAGE CONDITIONS. BY REDUCING LUBRICANT CONSUMPTION, THE COST DIFFERENCE WAS 

JUSTIFIED. EXTRA PROFITS FROM THE USE OF THE B-51 ALITHICON LUBRICANT WAS GENERATED BY 

REDUCING LUBRICANT REPLACEMENT, LABOR COSTS, LESS MACHINERY DOWNTIME, AND INCREASED 

PRODUCTION. 


* WITHSTANDS HIGH TEMPERATURES OF UP TO 700° F 

* WATERPROOF * EXTENDS BEARING LIFE OF UP TO 400% 

* WILL NOT MELT OR SLING FROM BEARINGS 


* EXCELLENT PUMPABILITY THROUGH CENTRALIZED LUBRICATION SYSTEMS 

* AN O.K. TIMKEN LOAD RATING OF 100 lbs, MINIMUM 

FOR TYPICAL SPECIFICATIONS, TEST RESULTS, APPLICATIONS, 

AND COMPATIBILITY INFORMATION, SEE REVERSE SIDE 


PHONE: 229-883-9515 / FAX: 229-883-9516 


B-51 ALITHICON SYNTHETIC LUBRICANT INFORMATION 

APPLICATIONS: DRY KILN FAN BEARINGS, SEALED FOR LIFE BEARINGS, STACK LOUVERS, COOKER 

BEARINGS, FLOTATION DRYER BEARINGS, TEXTILE MACHINERY, DOCTOR BEARINGS ON YANKEE DRYERS, 

ELECTRICAL GENERATING TURBINE LINKAGE BEARINGS, STOKER TRAVELING GRATE BEARINGS, AND MANY, 

MANY MORE. 

TYPICAL TEST DATA ASTM TEST B-51 

NLGI GRADE 1 


PROLONGED WORKED 

D-217 0.8 

PENETRATION, 

% CHANGE 

DROPPING POINT, MIN. D-566 NON-MELT 

TEMPERATURE OPERATING 

RANGE 

BASE FLUID 

VISCOSITY CENTISTOKES, 40° C 150 

+28° F TO +700° F 

TIMKEN O.K. LOAD, lbs, MIN. 2782 100 


EXCELLENT 

ROLL STABILITY, % CHANGE 1831 0.6 

LEAKAGE TENDENCIES, % MAX. D-1264 0.1 


38° C (100° F) 

70° C (175° F) 

OXIDATION STABILITY, MAX. 

PRESSURE DROP @ 100 hrs., KPS 

(PSI) 


WHICH WELDING OCCURS kg (lbs) 

WEAR PREVENTATIVE 

CHARACTERISTICS, MAX. SCAR 

DIAMETER 40 kg LOAD, 120 R.P.M. 

D-1264 


AVAILABLE PACKAGING 

* 30 - 14.5 oz TUBE CASE * 6 - 7.5 CAN CASE * 45 lb PAIL 

LUBRICANT COMPATIBILITY 

ALUMINUM COMPLEX BARIUM COMPLEX CALCIUM STEARATE 

0.02 

0.02 

D-942 1 

D-2596 3.94 

D-2266 .2 mm 


VISCOSITY SUS @ 100° F 743 


* 120 lb KEG * 420 lb DRUM * BULK 

CALCIUM 12-HYDROXY CALCIUM COMPLEX CALCIUM SULFONATE COMPLEX 

BENTONE / CLAY LITHIUM COMPLEX LITHIUM STEARATE 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON C-155 

SYNTHETIC BEARING LUBRICANT 

THE ALITHICON C-155 SYNTHETIC BEARING LUBRICANT IS SPECIFICALLY FORMULATED TO BE APPLIED 

WHERE CONVENTIONAL SOAP-THICKENED, OR SO CALLED NON-MELT GREASES, WILL NOT PROVIDE 

ADEQUATE PERFORMANCE. 

THE ALITHICON C-155 SYNTHETIC LUBRICANT IS A SYNTHETICALLY THICKENED GREASE WHICH 

EMPLOYS A HIGH THERMAL STABLE SYNTHETIC BASE FLUID, ALLOWING IT TO PROVIDE SUPERIOR 

LUBRICATION AND PROTECTION TO BEARINGS WHICH MUST OPERATE IN TEMPERATURES OF UP TO 

700° F WITHOUT MELTING OR HARDENING IN SERVICE. 

TWO ADDITIONAL IMPORTANT FEATURES OF THE ALITHICON C-155 SYNTHETIC LUBRICANT IS: BEING 

WATERPROOF, RESISTING WATER WASH-OUT, AND HAVING A LONG SERVICE LIFE, REDUCING GREASE 

CONSUMPTION AS MUCH AS 800% WHEN COMPARED TO OTHER GREASES NORMALLY USED IN THESE 

APPLICATIONS. 

THE ALITHICON C-155 SYNTHETIC LUBRICANT HAS AN O.K. TIMKEN LOAD RATING OF 100 lbs, MINIMUM, 

AND WILL PRODUCE AND EXTENDED BEARING LIFE OF UP TO 400%. 

IT IS NOT NECESSARY TO LIMIT THE USE OF THE ALITHICON C-155 SYNTHETIC LUBRICANT ONLY TO 

BEARINGS OPERATING UNDER EXTREME TEMPERATURES OR WET CONDITIONS TO JUSTIFY THE 

ADDITIONAL COST. MANY LONG-TIME USERS OF THE ALITHICON C-155 SYNTHETIC LUBRICANT STATE 

THAT IT WAS PRIMARILY PURCHASED FOR USE IN THESE EXTREME, HIGH MAINTENANCE AREAS, BUT IT 

WAS LATER TRIED IN BEARINGS ON MACHINERY OPERATING IN AMBIENT TEMPERATURES AND UNDER 


JUSTIFIED. EXTRA PROFITS FROM THE USE OF THE ALITHICON C-155 SYNTHETIC LUBRICANT WAS 

GENERATED BY REDUCING LUBRICANT REPLACEMENT, LABOR COSTS, LESS MACHINERY DOWNTIME, 

AND INCREASED PRODUCTION. 









AND COMPATIBILITY INFORMATION, SEE FOLLOWING PAGE 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON C-155 SYNTHETIC LUBRICANT INFORMATION 

APPLICATIONS: DRY KILN FAN BEARINGS, SEALED FOR LIFE BEARINGS, STACK LOUVERS, COOKER BEARINGS, 

FLOTATION DRYER BEARINGS, TEXTILE MACHINERY, DOCTOR BEARINGS ON YANKEE DRYERS, ELECTRICAL 

GENERATING TURBINE LINKAGE BEARINGS, STOKER TRAVELING GRATE BEARINGS, AND MANY, MANY MORE. 

TYPICAL TEST DATA ASTM TEST C-155 

NLGI GRADE 1.5 

COLOR 

BASE FLUID 

VISCOSITY CENTISTOKES, 40° C 1,400 

VISCOSITY SUS @ 100° F 6,485 







CLEAR 



D-217 0.8 

PENETRATION, 

% CHANGE 



RANGE 

+28° F TO +700° F 



EXCELLENT 




38° C (100° F) 

70° C (175° F) 



(PSI) 



D-1264 




0.02 

0.02 

D-942 1 

D-2596 3.94 


D-2266 .2 mm 




LITHIUM 12-HYDROXY SILICA SODIUM POLYUREA

ALITHICON C-155 

SYNTHETIC BEARING LUBRICANT 

THE ALITHICON C-155 SYNTHETIC BEARING LUBRICANT IS SPECIFICALLY FORMULATED TO BE APPLIED 

WHERE CONVENTIONAL SOAP-THICKENED, OR SO CALLED NON-MELT GREASES, WILL NOT PROVIDE 

ADEQUATE PERFORMANCE. 

THE ALITHICON C-155 SYNTHETIC LUBRICANT IS A SYNTHETICALLY THICKENED GREASE WHICH 

EMPLOYS A HIGH THERMAL STABLE SYNTHETIC BASE FLUID, ALLOWING IT TO PROVIDE SUPERIOR 

LUBRICATION AND PROTECTION TO BEARINGS WHICH MUST OPERATE IN TEMPERATURES OF UP TO 

700° F WITHOUT MELTING OR HARDENING IN SERVICE. 

TWO ADDITIONAL IMPORTANT FEATURES OF THE ALITHICON C-155 SYNTHETIC LUBRICANT IS: BEING 

WATERPROOF, RESISTING WATER WASH-OUT, AND HAVING A LONG SERVICE LIFE, REDUCING GREASE 

CONSUMPTION AS MUCH AS 800% WHEN COMPARED TO OTHER GREASES NORMALLY USED IN THESE 

APPLICATIONS. 

THE ALITHICON C-155 SYNTHETIC LUBRICANT HAS AN O.K. TIMKEN LOAD RATING OF 100 lbs, MINIMUM, 

AND WILL PRODUCE AND EXTENDED BEARING LIFE OF UP TO 400%. 

IT IS NOT NECESSARY TO LIMIT THE USE OF THE ALITHICON C-155 SYNTHETIC LUBRICANT ONLY TO 

BEARINGS OPERATING UNDER EXTREME TEMPERATURES OR WET CONDITIONS TO JUSTIFY THE 

ADDITIONAL COST. MANY LONG-TIME USERS OF THE ALITHICON C-155 SYNTHETIC LUBRICANT STATE 

THAT IT WAS PRIMARILY PURCHASED FOR USE IN THESE EXTREME, HIGH MAINTENANCE AREAS, BUT IT 

WAS LATER TRIED IN BEARINGS ON MACHINERY OPERATING IN AMBIENT TEMPERATURES AND UNDER 


JUSTIFIED. EXTRA PROFITS FROM THE USE OF THE ALITHICON C-155 SYNTHETIC LUBRICANT WAS 

GENERATED BY REDUCING LUBRICANT REPLACEMENT, LABOR COSTS, LESS MACHINERY DOWNTIME, 

AND INCREASED PRODUCTION. 











PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON C-155 SYNTHETIC LUBRICANT INFORMATION 

APPLICATIONS: DRY KILN FAN BEARINGS, SEALED FOR LIFE BEARINGS, STACK LOUVERS, COOKER BEARINGS, 

FLOTATION DRYER BEARINGS, TEXTILE MACHINERY, DOCTOR BEARINGS ON YANKEE DRYERS, ELECTRICAL 

GENERATING TURBINE LINKAGE BEARINGS, STOKER TRAVELING GRATE BEARINGS, AND MANY, MANY MORE. 

TYPICAL TEST DATA ASTM TEST C-155 

NLGI GRADE 1.5 

COLOR 

BASE FLUID 

VISCOSITY CENTISTOKES, 40° C 1,400 

VISCOSITY SUS @ 100° F 6,485 







CLEAR 



D-217 0.8 

PENETRATION, 

% CHANGE 



RANGE 

+28° F TO +700° F 



EXCELLENT 




38° C (100° F) 

70° C (175° F) 



(PSI) 



D-1264 




0.02 

0.02 

D-942 1 

D-2596 3.94 


D-2266 .2 mm 




LITHIUM 12-HYDROXY SILICA SODIUM POLYUREA

OG-7000 SEMI-SYNTHETIC 

OPEN GEAR LUBRICANT (NLGI-2) 

ALITHICON "OG-7000" SEMI-SYNTHETIC OPEN GEAR LUBRICANT WAS FORMULATED, TESTED, AND HAS 

BEEN PROVEN TO BE THE PREFERRED LUBRICANT FOR USE TO LUBRICATE OPEN GEARS FOUND ON 

MINING AND CONSTRUCTION EQUIPMENT. PLUS ALL TYPES OF INDUSTRIAL MACHINERY. 

THE ALITHICON "OG-7000" IS LEAD-FREE, TOTALLY WATERPROOF, AND WITHSTANDS HIGH 

TEMPERATURES. IT GREATLY REDUCES LUBRICANT CONSUMPTION AND RE-LUBRICATION INTERVALS, 

FOR THE ALITHICON "OG-7000" WILL NOT MELT, RUN, OR SLING OFF OPEN GEARS. 

THE ALITHICON "OG-7000 HAS UNIFORMLY DISPERSED, LOW-FRICTION INGREDIENTS, GIVING IT A HIGH 

FILM STRENGTH WITH HEAVY LOAD CARRYING CHARACTERISTICS, GREATLY REDUCED STARTING 

TORQUE, AND IS EXCELLENT FOR USE AT LOWER OPERATING TEMPERATURES. IT CAN BE APPLIED BY 

HAND OR PRESSURE GUN. 

THE ALITHICON "OG-7000" RECOMMENDED TEMPERATURE RANGE IS -5° F TO 565° F. 


* TOTALLY WATERPROOF 

* WITHSTANDS HIGH TEMPERATURES (565° F) 

* EXCELLENT FOR USE IN LOW TEMPERATURES (-5° F) 

* WILL NOT CHIP OR FLAKE AT LOW TEMPERATURES 

* CUSHIONS AND REDUCES OPEN GEAR NOISES 

* REDUCES LUBRICANT CONSUMPTION AS MUCH AS 200% 

* GREATLY EXTENDS OPEN GEAR LIFE 

* O.K. TIMKEN LOAD, 80 lbs, MINIMUM 

APPLICATIONS: EXPOSED GEARS OF ALL TYPES: STEAM AND POWER WINCHES, HOST, 

POWER SHOVELS, DREDGES, ROLLER GEARS, SHOVEL GEARS, WALKING MECHANISMS, 

DIPPERSTICKS, TREE SHAKERS, DRAWING MACHINERY, KILN GEARING, TRUCK-TRACTOR FIFTH 

WHEELS, SLOW-MOVING BEARINGS, WIRE ROPE AND CABLES, ELEVATOR TRACKS, ETC. 



ALITHICON LUBRICANTS CO., INC // P O BOX 5225 // ALBANY, GEORGIA 31706 

PHONE: 229-883-9515 // FAX: 229-883-9516 


OG-7000 SEMI-SYNTHETIC OPEN GEAR LUBRICANT (NLGI-2) 

NLGI GRADE 2 

COLOR 

BLACK 

TEXTURE 

TACKY 

WORKED PENETRATION, ASTM 273 

TIMKEN O.K. LOAD 80 

OXIDATION STABILITY, AFTER 500 hrs DROP 6 

OIL SEPARATION I.P. LEAKAGE, 7 DAYS @ 104° F 1.2 

SOLUBILITY - BOILING WATER 

INSOLUBLE 

BASE FLUID INFORMATION 

VISCOSITY S.S.U. @ 100° F 2,465 

VISCOSITY S.S.U. @ 210° F 167 


FLASH POINT, ° F 590 

FIRE POINT, ° F 680 

GRAVITY, A.P.I. 26 

OXIDATION INHIBITOR 

YES 

E.P. ADDITIVE 

YES 

RUST INHIBITOR 

YES 

POUR POINT, ° F -10 


* 50 / 11.5 oz CAULKING TUBE CASE * 120 lb KEG 

* 45 lb PAILS * 420 lb DRUM 

COMPATIBLE 


CALCIUM 12-HYDROXY 

SILICA 



INCOMPATIBLE 


BARIUM COMPLEX 

CALCIUM COMPLEX CALCIUM SULFONATE COMPLEX 



LITHIUM COMPLEX POLYUREA SODIUM 


PHONE: 229-883-9515 / FAX: 229-883-9516

7702 ALITHICON SYNTHETIC HI-TEMP 


7702 ALITHICON SYNTHETIC HI-TEMP BEARING LUBRICANT IS SPECIFICALLY FORMULATED TO 

BE APPLIED WHERE CONVENTIONAL SOAP THICKENED, OR CO-CALLED NON-MELT, CLAY 

THICKENED GREASES WILL NOT PROVIDE ADEQUATE PERFORMANCE. 

7702 ALITHICON SYNTHETIC HI-TEMP BEARING LUBRICANT IS FORMULATED WITH AN 

INORGANIC COPOLYMER BASE, A SYNTHETIC BASE OIL, SOUTHEAST OIL'S EXCLUSIVE WEAR 

REDUCING ADDITIVE "ALITHICON", ALONG WITH A SOLIDIFIED SECONDARY LUBRICANT. 

7702 WILL STAY IN THE BEARING OR LUBRICATED SURFACES, PROVIDING CONSTANT 

PROTECTION WHERE ORDINARY GREASES WILL MELT, RUN, OR HARDEN. EVEN AFTER 

TEMPERATURES ARE REACHED THAT WOULD CAUSE THE SYNTHETIC BASE OIL TO VOLATILE, 

A SECONDARY "DRY FILM" LUBRICANT REMAINS, PROVIDING ADEQUATE PROTECTION OF UP 

TO 1,600° F. 


* NON-MELTING * LESS LUBRICANT CONSUMED 

* PROTECTION UP TO 1,600° F * EXTENDS BEARING LIFE UP TO 300% 

* WITHSTANDS AND PROTECTS UNDER EXTREMELY HIGH TEMPERATURES 

APPLICATIONS: 

7702 HAS BEEN DESIGNED TO BE USED IN APPLICATIONS SUCH AS: SOAKING PIT COVERS, 

SOAKING PIT CRANES, ANNEALING PIT FURNACES, KILN CAR WHEELS, LADLE BEARINGS, OVEN 

CONVEYOR BEARINGS, HOMOGENIZER BEARINGS, ETC. 

CHANGE OVER INFORMATION: 

NOTICE: DIFFERENT GREASES MAY NOT MIX. TO BE SAFE, ALWAYS FLUSH BEARINGS AND 

BEARING FEED LINES UNTIL COMPLETELY FILLED WITH 7702 ALITHICON SYNTHETIC HI-TEMP 


FOR TYPICAL SPECIFICATIONS AND TEST RESULTS, SEE REVERSE SIDE. 


PHONE: 229-883-9515 // FAX: 229-883-9516 

E-MAIL: ALITHICON@ALITHICON.COM // WEBSITE: WWW.ALITHICON.COM


NLGI GRADE 2 

PENETRATION (ASTM D-217), WORKED 260 - 265 

TEXTURE 

MELTING POINT, ° F 

TACKY 

NON-MELTING 

TIMKEN O.K. LOAD, lbs., MIN. 80 

COLOR 

BASE OIL 


FLASH POINT 

FIRE POINT 


SILVER 

124 

596 

669 

160 


* 50 - 14.5 oz TUBES CASE * 120 lb KEG 

* 45 lb PAIL * 420 lb DRUM 

* BULK 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON 452000-FM FOOD MACHINERY 

BEARING LUBRICANT (NLGI-00) 

THE ALITHICON 452000-FM FOOD MACHINERY BEARING LUBRICANT IS DESIGNED TO MEET 

TODAY’S DEMANDING REQUIREMENTS OF THE MODERN FOOD PROCESSING EQUIPMENT, 

WHICH OPERATES UNDER EXTREMELY HIGH TEMPERATURES, HEAVY LOADS, HIGH SPEED, 

AND WET CONDITIONS. 

IT ALSO MEETS WITH THE FDA / USDA PURITY REQUIREMENTS WITH AN H-1 RATING FOR 

INCIDENTAL CONTACT WITH THE FOOD PRODUCTS BEING PROCESSED. 

THE ALITHICON 452000-FM FOOD MACHINERY BEARING LUBRICANT IS FORMULATED TO 

PERFORM IN A SUPERIOR MANNER WITH THE FOLLOWING OUTSTANDING FEATURES: A BROAD 

OPERATING RANGE (-10° F TO 550° F), WATERPROOF, MECHANICAL STABILITY (RESISTANCE TO 

HARDENING OR SOFTENING IN SERVICE), RUST AND OXIDATION RESISTANCE, AND HEAT 

REVERSION CHARACTERISITICS OR REVERSABILITY (THE ABILITY TO MAINTAIN ITS ORIGINAL 

CONSISTENCY AFTER BEING HEATED AND COOLED REPEATEDLY). 

WITH THE AVAILABILITY OF THE ALITHCON 452000-FM FOOD MACHINERY BEARING LUBRICANT, 

IT IS NOT NECESSARY TO SETTLE FOR SHORT BEARING LIFE, DECREASED PRODUCTION, AND 

EXCESSIVE EQUIPMENT REPAIRS JUST TO MEET WITH THESE USDA / FDA PURITY 

REQUIREMENTS. 


♦ TOTALLY WATERPROOF 

♦ WITHSTANDS HIGH TEMPERATURES OF UP TO 550° F 

♦ PREVENTS RUSTING IN BEARINGS 

♦ RATES AN O.K. TIMKEN LOAD OF 80 lbs, MIN. 

♦ MEETS THE FDA / USDA REQUIREMENTS OF H-1 FOR PURITY 

♦ TACKY - REDUCES LUBRICANT CONSUMPTION AS MUCH AS 300% 

♦ EXTENDS BEARING LIFE AS MUCH AS 400% 

CHECK THIS ALITHICON LUBRICANT FOR USDA APPROVAL, FOR USE IN FOOD PROCESSING 




PHONE: 229-883-9515 / FAX: 229-883-9516 


APPLICATIONS: 

ALL FOOD MACHINERY APPLICATIONS REQUIRING AND NLGI-00 LUBRICANT. 

EXCELLENT LUBRICANT TO LUBRICATE COUPLINGS, WHICH OPERATE BETWEEN 1 - 5,000 R.P.M.’S. 

ALITHICON 452000-FM FOOD MACHINERY LUBRICANT 

TYPICAL SPEFICATIONS: 

SPECIFICATION 

TEST RESULT 

NLGI GRADE 00 

WORKED PENETRATION, 60 STROKES (ASTM D-217) 410 

DROPPING POINT, MINIMUM (ASTM D-566) 550 

LUBRICATING OPERATING RANGE 

-10° TO 550° F 

TIMKEN O.K. LOAD, lbs, MINIMUM 80 


COLOR 

TEXTURE 

EXCELLENT 

SNOW WHITE 

SLIGHTLY TACKY 

EVAPORATION LOSS @ 350° F, WT. % (ASTM D-2595) 0.9 

USP SYNTHETIC HYDROCARBON BASE OIL VISCOSITY @ 40° C 100 

BASE FLUID VISCOSITY INDEX 120 


♦ 35 lb PAILS ♦ 45 lb PAILS ♦ 120 lb KEG 

♦ 420 lb DRUM 

♦ BULK 

452000-FM LUBRICANT COMPATIBILITY 


CALCIUM 12-HYDROXY 

LITHIUM COMPLEX 

SILICA 


BARIUM COMPLEX 


CALCIUM COMPLEX 




POLYUREA 

CALCIUM SULFONATE 

COMPLEX

ALITHICON OG-3000 E.P. PARA/SYNTHETIC 

OPEN GEAR LUBRICANT (AGMA 11 E.P.) 

THE ALITHICON OG-3000 E.P. PARA/SYNTHETIC OPEN GEAR OIL HAS BEEN DESIGNED, AND 

FORMULATED, TO LUBRICATE OPEN GEARS, WHICH OPERATE IN TEMPERATURES OF FROM 

+25° F TO UP TO 200° F. 

WITH THE ALITHICON OG-3000 E.P. PARA/SYNTHETIC OPEN GEAR LUBRICANT, BEING ABSENT 

FROM ANY TYPE OF SOLIDS, CONCERNS DUE TO LUBRICANT APPLICATION EQUIPMENT 

PLUGGING ARE ELIMINATED. 

THE ALITHICON OG-3000 E.P., BEING A PARA/SYNTHETIC FLUID CAN BE USED, AND IS 

RECOMMENDED FOR USE TO DISPERSE THROUGH LUBRICANT DELIVERY SYSTEMS DESIGNED 

TO PUMP 9 E.P., 11 E.P., AND 13 E.P. OPEN GEAR LUBRICANTS. THE CO-ADHESIVENESS OF THIS 

LUBRICANT WILL, NOT ONLY REDUCE LUBRICANT CONSUMPTION BY 50%, IT IS FORMULATED 

TO REDUCE WEAR, EXTENDING OPEN GEAR LIFE OF UP TO 500%. 


• WITHSTANDS TEMPERATURES OF UP TO 200° F. 

• EXCELLENT PERFORMANCE AT LOW TEMPERATURES 

• TIMKEN O.K. LOAD, 80 lbs., MIN. 

• ELIMINATES LUBRICANT DELIVERY SYSTEM PLUGGING 

• CLEANER AND A MORE SATISFACTORY OPEN GEAR LUBRICANT TO WORK WITH 

• REDUCES LUBRICANT CONSUMPTION BY 50% 

• EXTENDS OPEN GEAR LIFE OF UP TO 500% LONGER 

APPLICATIONS: 

OPEN GEARS FOUND ON PAPER MILL WOODYARD MACHINERY, CHEMICAL MANUFACTURING 

MACHINERY AND ALL OPEN GEARS REQUIRING LUBRICATION WITH A HEAVY FLUID. 

SEE REVERSE SIDE FOR TECHNICAL SPECIFICATIONS, 

TEST RESULTS AND AVAILABLE PACKAGING 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON OG-3000 E.P. PARA/SYNTHETIC 

OPEN GEAR LUBRICANT (AGMA 11 E.P.) 

TEST 

RESULTS 

ISO GRADE 3,000 

AGMA GRADE 

11 E.P. 

VISCOSITY, Cst @ 40° C (ASTM D-0445) 3,000 

VISCOSITY, Cst @ 100° C (ASTM D-0445) 129 


FLASH POINT, coc, ° F. (ASTM D-0092) 620 

POUR POINT, ° F. (ASTM D-0097) +15 

API GRAVITY (ASTM D-4052) 20.1 

TIMKEN O.K. LOAD, lbs., MIN. (ASTM 2782) 80 

COLOR (ASTM D-1500) 

8 (DARK AMBER) 


* 35 lbs PAIL * 45 lbs PAIL 

* 120 lbs KEG * 420 lbs DRUM 

* 2,500 lb DISPOSABLE TOTE TANK * BULK 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON 4500 SPECIAL LUBRICANT 

THE ALITHICON 4500 SPECIAL LUBRICANT IS FORMULATED TO ENSURE THE FLEXIBILITY OF ROLLER 

CHAINS, ENSURING SMOOTH OPERATION, KEEPING CHAINS FROM JUMPING SPROCKETS AND GREATLY 

REDUCING BREAKAGE. 

ROUGH CHAIN OPERATION INCREASES POWER CONSUMPTION. PREMATURE WEAR SHORTENS CHAIN 

AND SPROCKET LIFE, WHICH CAUSES RAPID CHAIN "STRETCHING", A CRITICAL FAILURE IN MACHINES 

WHERE MACHINERY SYNCHRONIZATION IS A CHAIN FUNCTION. 

WHEN APPLIED TO ROLLER CHAINS, THE ALITHICON 4500 SPECIAL LUBRICANT READILY PENETRATES 

INTO THE PINS AND BUSHINGS, REDUCING WEAR AND EXTENDING CHAIN AND SPROCKET LIFE UP TO 

400% LONGER THAN THE MORE COMMONLY USED LUBRICANTS. 

BEING WATERPROOF, WATER AND STEAM DO NOT TEND TO WASH IT OFF, AND RUST AND CORROSION 

ARE ELIMINATED. 

THE ALITHICON 4500 IS A TACKY, WATERPROOF, DRIPLESS, HIGH TEMPERATURE (WITHSTANDING 580° F) 

LUBRICANT, MAKING IT UNMATCHED IN PERFORMANCE AS A CHAIN LUBRICANT. 

THE ALITHICON 4500 SPECIAL LUBRICANT IS THE PREFERRED LUBRICANT, TO LUBRICATE WHEEL 

BEARINGS, WHICH ARE NORMALLY LUBRICATED WITH AN 85w/140 GEAR OIL. THE ALITHICON 4500 

SPECIAL LUBRICANT WILL EXTEND WHEEL BEARING LIFE OF UP TO 400% LONGER, WHILE ELIMINATING 

SEAL SEAPAGE. 


* WATERPROOF * EASY TO APPLY 

* WITHSTANDS HIGH TEMPERATURES AS MUCH AS 580° F * WILL NOT SLING OR DRIP 

* ENSURES A SAFER, QUIETER OPERATION 

* ELIMINATES RUST AND CORROSION 

* VIRTUALLY ELIMINATES CHAIN STRETCHING 

* EXTENDS CHAIN, SPROCKET, AND CABLE LIFE UP TO 400% 

* EXTENDS WHEEL BEARING LIFE OF UP TO 400% 

* ELIMINATES WHEEL BEARING SEAL LEAKS 

APPLICATIONS: READY-MIX CONCRETE TRUCK MIXING DRUM GEAR REDUCERS, ALL ROLLER CHAINS, 

CABLES, SLOW SPEED ENCLOSED GEAR REDUCERS, OIL FILLED WHEEL BEARINGS, SEMI-TRUCK 

TRAILER DOLLY GEARINGS, ROTARY MOWER GEAR REDUCERS, CONSTRUCTION EQUIPMENT SEALED 

TRACK ROLLERS, LUMBER MILL FETCHER SHAFTS, HOUR GLASS CONVEYOR CHAINS, PLANETARY 

GEARS, PLUS MANY MORE. 

METHOD OF APPLICATIONS: SQUIRT CAN, PAINT BRUSH, FREE POURING, GREASE GUN, GEAR OIL 

PUMP, OR A CENTRALIZED LUBRICATING SYSTEM. 

SEE REVERSE SIDE FOR TYPICAL SPECIFICATIONS. 


PHONE: 229-883-9515 // FAX: 229-883-9516 

E-MAIL: ALITHICON@ALITHICON.COM // WEBSITE: WWW.ALITHICON.COM

ALITHICON 4500 SPECIAL LUBRICANT 


NLGI GRADE 00 


PROLONGED WORKED PENETRATION 

(ASTM D-217), % CHANGE 0 

DROPPINT POINT, MIN. (ASTM D-566), ° F. 580 



EXCELLENT 


LEAKAGE TENDENCIES, % MAX. (ASTM D-1264) 0 


30° C. (100° F.) 

79° C. (175° F.) 



0.01 

0.012 

FOUR BALL METHOD, MAX. OAD WHICH 

WELDING OCCURS, kg (lbs) (ASTM D-2266) 2.96 

WEAR PREVENTATIVE CHARACTERISTICS (ASTM D-2266), 

MAX SCAR DIAMETER 40 kg LOAD, 1200 R.P.M. 


COPPER STRIP CORROSION (ASTM D-130) 

COLOR 

1 mm 

1 A (PASS) 

BRONZE 

ALITHICON 4500 SPECIAL LUBRICANT WHEEL BEARING 

BENCH TEST RESULTS: 

PHASE 1: WHEEL HUBS WERE FILLED WITH THE ALITHICON 4500 SPECIAL LUBRICANT. THE BEARINGS WERE LOADED TO 1,000 

lbs OF TEST WEIGHT AND ROTATED FOR 150 MINUTES (2.5 HOURS), OR APPROXIMATELY 100 ROAD MILES. TEST END OPERATING 

TEMPERATURES WERE RECORDED: 84° F. 

PHASE 2: AT THE END OF THE WHEEL BEARING TEST: PHASE #1, THE WHEEL BEARING RESERVOIR WAS DRAINED OF THE 

ALITHICON 4500 SPECIAL LUBRICANT, LEAVING THE LUBRICANT WHICH COATED THE BEARINGS. THE BEARINGS WERE LOADED 

TO 1,000 lbs WEIGHT AND ROTATED FOR 450 MINUTES (7.5 HOURS) OR APPROXIMATELY 300 MILES. TEST END OPERATING 

TEMPERATURES WERE RECORDED, 85° F. AFTER DISASSEMBLY, BEARINGS SHOW NO MEASURABLE SIGNS OF WEAR. 


COMPATIBLE 

INCOMPATIBLE 

CALCIUM STEARATE ALUMINUM COMPLEX BARIUM COMPLEX 

BENTONE / CLAY CALCIUM COMPLEX CALCIUM SULFONATE COMPLEX 

CALCIUM 12-HYDROXY LITHIUM STEARATE LITHIUM 12-HYDROXY 

SILICA LITHIUM COMPLEX POLYUREA SODIUM 


* 45 lb (6 GALLON) PAIL 

* 120 lb (16 GALLON) KEG 

* 420 lb (55 GALLON DRUM 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON GASOLINE & DIESEL FUEL IMPROVER 

THE PREFERRED FUEL TREATMENT FOR BOTH GASOLINE AND DIESEL FUEL 

A MODERN DIESEL FUEL TREATMENT, MEETING THE NEW E.P.A. LOW SULFUR 

REQUIREMENTS, WITHOUT SACRIFICING EQUIPMENT PERFORMANCE. 

REGULATION BY THE E.P.A. MANDATE THAT ALL DIESEL FUELS INTENDED FOR ON-HIGHWAY USE MUST 

HAVE A LOW SULFUR CONTENT. CURRENT FUELS HAVE A SULFUR LEVEL OF ABOUT 0.25%, WHILE NEW 

FUELS ARE REQUIRED TO HAVE A 0.05% MAXIMUM. 

IN ORDER TO REDUCE THE SULFUR LEVEL TO VALUES OF 0.05% AND LESS, A REFINING PROCESS 

CALLED “HYDROTREATING” IS UTILIZED. THIS PROCESS ALTERS THE MATERIAL BY CHANGING SOME OF 

THE AROMATIC COMPOUNDS TO SATURATES, WHICH CAUSES THE PROBLEMS. IT IS THE REMOVAL OF 

THE POLYAROMATICS, NITROGEN, AND SULFUR COMPOUNDS THAT IS REDUCING TH PROPER 

BOUNDARY LUBRICATION, BETWEEN THE LOADED MOVING PARTS. INSPECTIONS OF THE FAILED 

SYSTEMS (PREDOMINATELY, ROTARY FUEL PUMPS) HAS DEMONSTRATED THE INCREASE IN SCUFFING 

WEAR. 

UNFORTUNATELY, REDUCING THE SULFUR CONTENT IN DIESEL FUEL COULD CAUSE AN IMPACT ON THE 

FUEL ECONOMY BECAUSE THERE SEEMS TO BE A REDUCTION IN THE BTU/GALLON OF ABOUT 10%. 

THEREFORE, THE REDUCED LEVEL COULD CAUSE AN INCREASE IN FUEL CONSUMPTION. 

THE ALITHICON GASOLINE & DIESEL FUEL IMPROVER IS FORMULATED TO ENSURE MAXIMUM 

PERFORMANCE AND LESS ENGINE WEAR, PROVIDING LONGER ENGINE LIFE WITH LESS MAINTENANCE 

AND DOWNTIME. 

THE ALITHICON GASOLINE & DIESEL FUEL IMPROVER BREAKS A DROP OF WATER INTO, 

APPROXIMATELY 1 MILLION PARTS, ABSORBING IT THROUGH-OUT THE DIESEL FUEL , WHICH ALLOWS 

THE WATER TO PASS THROUGH THE COMBUSTION PROCESS, IN PARTICLES SO SMALL, THE 

PERFORMANCE OF THE ENGINE IS NOT AFFECTED. 


* EASIER ENGINE STARTING * GREATLY EXTENDS ROTARY FUEL PUMP LIFE 

* INCREASED POWER PERFORMANCE * MORE SATISFACTORY ENGINE IDLING 

* REDUCES ALGAE GROWTH * REDUCES DIESEL FUEL POUR POINT 

* ELIMINATES FUEL INJECTOR NOZZLE PLUGGING 

* PROVIDES WATER PROTECTION - ABSORBS MOISTURE 

* INCREASES CETANE RATING AS MUCH AS 15% 

* INCREASES MILES PER GALLON AS MUCH AS 10% 

* REDUCES BLACK EXHAUST SMOKE TO A LIGHT GRAY HAZE 

SEE REVERSE SIDE FOR TYPICAL SPECIFICATIONS. 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON GASOLINE & DIESEL FUEL IMPROVER 


FLASH POINT, ° F. (ASTM D-92) 119 

CORROSION TEST (ASTM D-665) 

PASS 

VARNISH & GUM TEST (ASTM D-189) 

PASS 

POUR POINT, ° F. - 70 

SPECIFIC GRAVITY, DEGREES, API 27.5 

VISCOSITY SUS @ 100° F. 54.1 

VISCOSITY SUS @ 32° F. 296 

VISCOSITY SUS @ 0° F. 1205 

ACID NEUTRALIZER TEST 

EXCELLENT 

MOISTURE ABSORBTION TEST 

EXCELLENT 

COLOR 

LIGHT AMBER 


* 24 / 1 QUART CASE 


* 6 GALLON PLASTIC PAIL 


TREATMENT RATIO: 

ONE GALLON OF ALITHICON DIESEL FUEL IMPROVER TREATS 500 GALLONS OF GASOLINE OR DIESEL 

FUEL. ON THE INITIAL TREATMENT, IT IS SUGGESTED TO MIX ONE GALLON OF ALITHICON GASOLINE & 

DIESEL FUEL IMPROVER TO 100 GALLONS OF GASOLINE OR DIESEL FUEL TO ENSURE A CLEAN FUEL 

SYSTEM. 

(1) OUNCE OF ALITHICON GASOLINE AND DIESEL FUEL IMPROVER TREATS (3) GALLONS OF GASOLINE 

OR DIESEL FUEL. 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON 767 

CHAIN, CABLE, OPEN-GEAR, 

& BEARING AEROSOL LUBRICANT 

THE ALITHICON 767 AEROSOL LUBRICANT IS AN EXCELLENT LUBRICANT DESIGNED FOR USE 

TO LUBRICATE ROLLER CHAINS, CABLES, OPEN-GEARS, WORKING MECHANISMS, AND 

BEARINGS. IT IS A TACKY LUBRICANT, WHICH IS EASY TO APPLY, RESISTS WATER WASH-OFF, 

AND WITHSTANDS TEMPERATURES OF UP TO 540° F WITHOUT MELTING OR DRIPPING. 

THE ALITHICON 767 AEROSOL LUBRICANT IS OUR 2212 BEARING LUBRICANT, WHICH HAS BEEN 

THINNED WITH HEPTANE AND PRESSURIZED IN AN AEROSOL CAN FOR EASY APPLICATION. 

WHEN THE ALITHICON 767 LUBRICANT IS APPLIED TO ROLLER CHAINS, THE EXTREMELY THIN 

LUBRICANT WILL PENETRATE INSTANTLY INTO THE PINS AND BUSHINGS, THEN IN 

APPROXIMATELY 180 SECONDS, THE SOLVENTS WILL EVAPORATE, LEAVING EACH CHAIN LINK 

LUBRICATED FROM THE INSIDE OUT. 

THE ALITHICON 767 LUBRICANT WILL ELIMINATE CHAIN LINK FREEZING AND CHAIN SPROCKET 

JUMPING. ROLLER CHAINS AND CHAIN SPROCKET LIFE ARE EXTENDED OF UP TO 500% WHEN 

PROPERLY USING THE 767. 

THE ALITHICON 767 AEROSOL LUBRICANT PENETRATES INSIDE CABLES, THEN DRIES TO AN 

NLGI-2 GREASE, LUBRICATING EACH STRAND, AND CABLE LIFE IS GREATLY EXTENDED. 

WHEN THE ALITHICON 767 AEROSOL LUBRICANT IS USED TO LUBRICATE OPEN GEARS AND 

HARD-TO-REACH WORKING MECHANISMS, IT REACTS IN THE SAME MANNER. IT COATS THE 

SURFACES, THEN DRIES TO A LIGHT-WEIGHT GREASE, OFFERING A PROTECTIVE CUSHION, 

THUS GREATLY REDUCING WEAR. 


* EASY TO APPLY * RESISTS WATER WASH-OFF 

* RATES AN O.K. TIMKEN LOAD OF 70 lbs., MIN. 

* RESISTS THE ATTRACTION OF LINT, DIRT, OR DUST 

* GREATLY REDUCES WEAR AND EXTENDS EQUIPMENT LIFE 

* FREE OF HEXANE 

APPLICATIONS: ROLLER CHAINS, CABLES, OPEN GEARS, WORKING MECHANISMS, SLIDING 

SURFACES, MOTOR GRADER CIRCLES, PIVOT POINTS, BEARINGS, ETC. 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON 767 

CHAIN, CABLE, OPEN-GEAR, 

& BEARING AEROSOL LUBRICANT 


ABSENCE OF VOLATILE INGREDIENTS 


NLGI GRADE 2 


PROLONGED WORKED PENETRATIONS 

(ASTM D-217), % CHANGE < 1.5 

DROPPING POINT, MIN. (ASTM D-566) 

NONE 



EXCELLENT 




39° C (100° F) 

79° C (175° F) 



FOUR BALL METHOD, MAX. LOAD WHICH WELDING OCCURS 2.76 

WEAR PREVENTATIVE CHARACTERISTICS (ASTM D-2666) 

MAX., SCAR DIAMETER 40 kg LOAD, 1200 R.P.M. 

COLOR 

BASE OIL: 


VISCOSITY CTS @ 100° F 


VISCOSITY CTS @ 210° F 


1.9 

4.3 

0.425 mm 

RED 

693 

149 

77 

17.1 

110 

AVAILABLE PACKAGING: 12 / 16.22 fl oz CAN CASE 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON P-88 

ROLLER CHAIN & PENETRATING LUBRICANT 

THE ALITHICON P-88 IS FORMULATED FOR USE TO LUBRICATE ROLLER CHAINS FOUND 

ON FARM AND INDUSTRIAL MACHINERY WHERE NORMALLY USED ROLLER CHAIN 

LUBRICANTS ATTRACT DIRT AND OTHER ABRASIVES, CREATING AN ABRASIVE 

COMPOUND WHICH EXCELERATES WEAR AND SHORTENS CHAIN LIFE. 

THE ALITHICON P-88 ROLLER CHAIN LUBRICANT WILL NOT ATTRACT DIRT AND 

ABRASIVES AND WILL EXTEND ROLLER CHAIN LIFE OF UP TO 400%. 

THE ALITHICON P-88 DISSOLVES AND PENETRATES RUST. IT IS THE PREFERRED 

CHOICE TO USE TO LOOSEN RUSTY BOLTS AND NUTS. 

THE ALITHICON P-88 DISPLACES MOISTURE. JUST SPRAY PARTS OR SURFACES, WAIT 

A FEW MINUTES, AND WIPE OFF WITH A CLOTH. RESPRAY FOR LONG-TERM 

PROTECTION. 

THE ALITHICON P-88 IS AN EXCELLENT QUICK-START SPRAY, REPLACING ETHER, TO 

AID IN CRANKING DIFFICULT-TO-START DIESEL ENGINES. 

THE ALITHICON P-88 WILL NOT VAPOR LOCK DIESEL ENGINES, AS DOES ETHER. 

* EXTENDS ROLLER CHAIN LIFE OF UP TO 400% 

* WILL NOT ATTRACT DIRT AND ABRASIVES 

* DISSOLVES AND PREVENTS RUST 

* DISPLACES MOISTURE * CONTAINS TEFLON 

* PENETRATES RUST TO LOOSEN RUSTY BOLTS & NUTS 

* A DIESEL ENGINE QUICK START SPRAY - REPLACING ETHER 

* MEETS WITH USDA / FDA H-2 REQUIREMENTS 

WHEN USING THE ALITHICON P-88 TO LUBRICATE ROLLER CHAINS, CHAIN FREEZING 

AND CRIMPING, AND CHAIN SPROCKET JUMPING IS ELIMINATED. AS A RESULT, 

ROLLER CHAIN AND SPROCKET LIFE IS GREATLY EXTENDED. 

MANUFACTURED 

UNDER ISO 9001 

CERTIFIED 

STANDARD 


PHONE: 229-883-9515 / FAX: 229-883-9516 



PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON FM-555 AEROSOL FOOD MACHINERY 

CHAIN AND PENETRATING FLUID 

THE ALITHICON FM-555 AEROSOL FOOD MACHINERY CHAIN AND PENETRATING LUBRICANT IS 

NON-TOXIC, PENETRATES, LUBRICATES, REDUCES WEAR, AND ELIMINATES RUSTING. 

IT IS SPECIFICALLY FORMULATED TO EFFECTIVELY REDUCE THE WEAR OF ROLLER CHAINS, 

PIVOT POINTS, AND BEARINGS FOUND ON FOOD PACKAGING AND PROCESSING EQUIPMENT, 

WHICH OPERATE UNDER TEMPERATURES OF FROM -100° F TO 500° F. IT TOTALLY REJECTS 

WATER AND THE EFFECTS OF STEAM. 

THE ALITHICON FM-555 AEROSOL FOOD MACHINERY CHAIN AND PENETRATING LUBRICANT IS 

COLORLESS AND ODORLESS, IS AUTHORIZED BY USDA, WITH AN H-1 RATING, FOR USE IN 

FEDERALLY INSPECTED MEAT AND POULTRY PLANTS, AND IT ALSO COMPLIES WITH FDA 

TITLE 21, PART 178, SECTION 178.3570 AND PART 172, SECTION 172.878. IT IS APPROVED FOR 

USE WHERE THE INCIDENTAL CONTACT WITH FOOD, EDIBLE PRODUCTS IS POSSIBLE. 

THE ALITHICON FM-555 AEROSOL FOOD MACHINERY CHAIN AND PENETRATING LUBRICANT 

DOES NOT CONTAIN ANY OZONE-DEPLETING CHLORINATED SOLVENTS. 


* EASY TO APPLY * OUTSTANDINGLY REDUCES WEAR 

* ELIMINATES RUSTING * REJECTS WATER AND STEAM 

* OPERATING TEMPERATURE RANGE OF -100° F TO 500° F 

* PENETRATES AND DISSOLVES CORROSION 

* GREATLY EXTENDS ROLLER CHAIN AND BEARING LIFE 

THE ALITHICON FM-555 AEROSOL FOOD MACHINERY CHAIN AND CABLE LUBRICANT HAS 

PROVEN TO BE THE PREFERRED CHOICE LUBRICANT FOR THE FOLLOWING APPLICATIONS: 

ROLLER CHAINS * BEARINGS * CABLES * CASTERS * CONVEYORS * SHACKLES, SLIDES, 

MIXERS, GRINDERS, STRETCH WRAPPERS, DEBONERS, BREAST PROCESSORS, TROLLEY AND 

TROLLEY BRACKETS, FROZEN MEAT BREAKERS, HATCHING TRAYS, POULTRY PICKERS, PUSH 

CARTS, SPICE MIXERS, AND MANY, MANY MORE APPLICATIONS FOUND IN THE FOOD 

INDUSTRY. 

FOR TYPICAL SPECIFICATIONS AND TEST RESULTS, SEE REVERSE SIDE 


PHONE: 229-883-9515 / FAX: 229-883-9516 


ALITHICON FM-555 AEROSOL 

FOOD MACHINERY CHAIN AND PENETRATING FLUID 


SPECIFICATIONS 

ASTM 

TEST 

RESULTS 

U.S.D.A., AUTHORIZED H-1 

VISCOSITY 

@ 100° F 

@ 210° F 

D-88 

D-88 

VISCOSITY INDEX D-567 150 

POUR POINT, ° F D-2500 -100 

FLASH POINT, ° F D-92 565 

FIRE POINT, ° F D-92 605 

TURBINE RUST TEST D-665 PASS 

OXIDATION STABILITY, hrs D-943 9000+ 

TIMKEN, O.K. LOAD, lbs, MIN. D-2782 80 

FOUR BALL E.P. TEST 

LOAD WEAR INDEX 

SEIZURE 

WELD 

D-2596 

60 

110 

180 

155 

45 


12 / 12 oz CANS / AEROSOL CASE 


PHONE: 229-883-9515 / FAX: 229-883-9516

alithicon “fleet” synthetic enclosed gear and transmission lubricants

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?