Explorerfix Child Car Seat - Kiddicare

More documents

Recommendations

Info

GENERAL INSTRUCTIONS GROUP 1 (9 - 18 KG.) Installation of the Explorerfix seat facing forwards with Isofix fastening system (see illustrations 01 - 07) • Fasten the two centering points of the Isofix fastening system hooks, whose normal position is the intersection between the rear part of the seat and the lower part of the backrest (fig. 01). • Place the safety seat on the rear vehicle seat facing forwards opposite the fasteners (fig. 02). • Pull the front knob (fig. 03) outwards and turn it to the right (fig. 04) to obtain the maximum length of the connectors. • Use both hands to press the seat towards the fasteners until it clicks indicating that both sides are fastened (fig. 05). • If the installation is correct, a green line will appear on the outer part of both connector release devices (fig. 06). • Lastly, adjust the space between the safety seat and the backrest of the vehicle by pulling the knob outwards and turning it to the left (fig. 07). WARNING: The seat can never be installed on the front seat of the vehicle with the Isofix fastening system plus the Top Tether. CONSULT THE LIST OF VEHICLES FOR THE INSTALLATION WITH THE SUPPORT LEG. Fitting the Top Tether (see illustrations 08 - 10) • The Top Tether strap is in the pocket on the back of the frame (fig. 08). • Hook the Top Tether karabiner (adjuster side) into the ring on the free end of the strap that is fastened onto the frame and the other end to the corresponding fastening point of the vehicle (fig. 09). • Tighten the strap until the adjuster clicks, indicating that it is at the correct tension (fig. 10). WARNING: CONSULT THE VEHICLE HANDBOOK TO LOCATE THE POSITION OF THE TOP TETHER RING. Removing the Explorerfix seat with Top Tether (see illustrations 11 - 13) • Pull the front knob outwards (fig. 03) and turn it to the right to obtain a space between the seat and the backrest of the vehicle (fig. 04). • Disconnect the Isofix system, pulling the buttons on both sides of the connector release devices. A red line will appear on one of them if it is correct (fig. 11). • Dismantle the Top Tether loosening the adjuster (fig. 12) and unhooking the karabiner from the upper part of the strap (fig. 13).
Fitting the Support Leg (see illustrations 14 - 16) • Once the safety seat has been fastened onto the vehicle seat using the Isofix system and its correct installation has been checked (see green line on the outer side of both of the connector release devices). • Remove the two stoppers from the front part of the base (fig. 14). • Simultaneously press the two pivot pins on the upper tubes of the support leg. • Insert both of them into the front slots making sure they go in simultaneously to stop them from blocking (fig. 15). When they click they are fastened correctly. • Pull the red release catch outwards with one hand, while, with the other hand, press the telescopic support of the leg against the floor of the vehicle. Release this part and check that the leg is not in-between two locking positions (fig. 16). • If the leg is in-between two positions, pull the red release catch outwards again and lengthen or shorten the leg to the upper or lower locking position to obtain the maximum support possible. Removing the Explorerfix seat with Support Leg (see illustrations 17 - 18) • Pull the red release catch outwards with one hand, while the other hand folds up the telescopic support (fig. 17). • Simultaneously press the two buttons on the upper part of the base and at the same time pull the upper tubes of the support leg (fig. 18). • Next, loosen the Explorerfix seat by pulling the front knob outwards and turning it to the right to create a space between the seat and the backrest of the vehicle. • Disconnect the Isofix system by pulling the buttons on both sides of the connector release devices. A red line will appear on them if it is correct. • Remove the seat from the vehicle seat. IMPORTANT WARNING: *DO NOT USE ON PASSENGER SEATS FITTED WITH A FRONT AIRBAG UNLESS YOUR VEHICLE MANUFACTURER CONFIRMS IT IS SAFE GROUP 1 (9 - 18 KG.) Installation of the Explorerfix seat facing forwards with three-point seat belt (car seat belt) (see illustrations 19 - 22) • Place the seat on the front* or rear seat of the car. • Pass the lap section of the seat belt through the guides on both sides (fig. 19), fasten the buckle and tighten the belt. • Next, pull the chest part of the seat belt passing it through the clip (fig. 20 - 21). • Fasten the safety catch (fig. 22). Adjusting the crotch strap (see illustration 23) • Press the adjuster and at the same time place it in the desired position (fig. 23), making sure that the lap section of the harness is positioned as low as possible so the pelvis is firmly secured.
Page 1 and 2: Explorerfix Child Car Seat Group 1
Page 3 and 4: 13 14 15 16 17 18 19 20 21 22 23 24
Page 5 and 6: CONGRATULATIONS PARENTS Silver Cros
Page 7: WARNINGS AND SAFETY NOTES IMPORTANT
Page 11 and 12: Installation of the Explorerfix sea

Explorerfix Child Car Seat - Kiddicare

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?