2402 pH StratosÂ® - Knick Elektronische MeÃgerÃ¤te GmbH & Co.

More documents

Recommendations

Info

Explosion protection 114 Stratos e 2402 pH
Warnings and notes to ensure safe operation Warning: Warning: Warning: Do not disconnect equipment unless power has been switched off. Clean only with antistatic moistened cloth. Substitution of components may impair suitability for hazardous locations. • The equipment shall be installed and protected from mechanical impact and ultraviolet (UV) sources. • Clean only with a moistened antistatic cloth as potential electrostatic hazard may exist. Service equipment only with conductive clothing, footwear and personal grounding devices to prevent electrostatic accumulation. • Internal grounding provisions shall be provided for field wiring. Bonding between conduit shall be provided during installation, and all exposed non-current carrying metallic parts shall be bonded and grounded. • Installation in a Class I, Division 2 or Class I, Zone 2 hazardous location shall be in accordance with the Canadian Electrical Code (CEC Part 1) Section 18 Division 2 wiring methods. • The equipment shall have a switch or circuit breaker in the building installation (that is in close proximity to the equipment) that is marked as the disconnect switch. • The enclosure Type 2 is only for indoor use. • The mains supply voltage fluctuations should not exceed -15/+10 percent of the nominal supply voltage. • Do not use the equipment in a manner not specified in this documentation. • Caution: Use supply wires suitable for 30 °C above ambient and rated at least 250 V. • Caution: Use signal wires suitable for at least 250 V. SPECIAL INSTRUCTIONS FOR FIELD REPRESENTATIVES None 115
Page 1 and 2:
Stratos ® 2402 pH Instruction manu
Page 3 and 4:
Contents Safety information . . . .
Page 5 and 6:
Safety information Be sure to read
Page 8 and 9:
70084 Bedienungsanleitung Safety pr
Page 10 and 11:
Assembly Package contents Check the
Page 12 and 13:
Pipe mounting, panel mounting 40 60
Page 14 and 15:
Installation and connection Informa
Page 16 and 17:
Connecting the VP cable Connecting
Page 18 and 19:
Typical wirings pH Example 1: pH me
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Typical wirings Example 9: pH measu
Page 28:
Typical wirings Example 11: pH meas
Page 31 and 32:
Example 13: ORP measurement with mo
Page 33 and 34:
Typical protective wiring measures
Page 35 and 36:
Display 1 2 3 4 5 6 7 8 9 10 20 19
Page 37 and 38:
Safety functions Sensocheck, Sensof
Page 39 and 40:
To activate the Hold mode from outs
Page 41 and 42:
Menu structure of configuration The
Page 43 and 44:
Code Menu Selection / Default ALrt
Page 45 and 46:
Code Display Action Choices o1. Sel
Page 47 and 48:
Code Display Action Choices o1. Set
Page 49 and 50:
Code Display Action Choices o1. Tim
Page 51 and 52:
Code Display Action Choices o1. 22
Page 53 and 54:
Code Display Action Choices o2. Spe
Page 55 and 56:
Code Display Action Choices o2. Tim
Page 57 and 58:
Code Display Action Choices o2. 22
Page 59 and 60:
Code Display Action Choices tc. Sel
Page 61 and 62:
Code Display Action Choices CA. For
Page 63 and 64: Code Display Action Choices AL. Sel
Page 65 and 66: Code Display Action Choices rL. Use
Page 67 and 68: Code Display Action Choices L2. Sel
Page 69 and 70: Code Display Action Choices Ct. Set
Page 71 and 72: Code Display Action (calibration pr
Page 73 and 74: Default settings of parameter sets
Page 75 and 76: Code. Parameter Setting rL. Relay f
Page 77 and 78: pH calibration Calibration is used
Page 79 and 80: Display Action Remark At the end of
Page 81 and 82: Display Action Remark Stability che
Page 83 and 84: Display Action Remark Stability che
Page 85 and 86: Convert slope [%] to slope [mV/pH]
Page 87 and 88: Display Action Remark Measuring mod
Page 89 and 90: Display Action Remark Activate cali
Page 91 and 92: Diagnostics functions Display Remar
Page 93 and 94: Display Action / Remarks Controller
Page 95 and 96: Controller equations Controller out
Page 97 and 98: Connecting a rinsing system The “
Page 99 and 100: Error ERR 03 Symbol (flashing) Prob
Page 101 and 102: Symbol flashes: Problem Possible ca
Page 103 and 104: Operating state Out 1 Out 2 Rel.1/2
Page 105 and 106: Display Problem Asymmetry potential
Page 107 and 108: Appendix Product line and accessori
Page 109 and 110: Zero adjustment Max. calibration ra
Page 111 and 112: Limit values Contact ratings Contac
Page 113: Protection against Protective separ
Page 117 and 118: 117
Page 119 and 120: 119
Page 121 and 122: 121 -02- Merck Titrisols, Riedel Fi
Page 123 and 124: 123 -04- Technical buffers to NIST
Page 125 and 126: -06- HACH buffers Nominal value: 4.
Page 127 and 128: -08- Hamilton Duracal buffers °C p
Page 129 and 130: Durafet Durafet adapter Electrode s
Page 131 and 132: Slope Two-point calibration See Ele
Page 133 and 134: Configuration: Output 1 44 Measurem
Page 135 and 136: L Limit function (LiMIT) 65 M Measu
Page 137 and 138: W Warranty 2 Wiring 15 Examples 18
Page 139 and 140: 139
show all

2402 pH StratosÂ® - Knick Elektronische MeÃgerÃ¤te GmbH & Co.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?

2402 pH StratosÂ® - Knick Elektronische MeÃgerÃ¤te GmbH & Co.